Restore the performance of your Fortress oil cap with this complete service kit. Includes rubber plugs, oil fill plugs, and O-ring seals to prevent leaks, maintain pressure, and keep your hub looking squeaky clean.
Replace a worn or leaking copper washer on your Dexter disc brake caliper. This 7/16" crush washer provides a tight, reliable seal between the banjo fitting and caliper to help prevent brake fluid leaks in your hydraulic braking system.
This replacement inner member slide easily fits into the existing housing of your Dexter XR84 or Legacy UFP surge brake actuator. For use with triple-axle trailers with hydraulic disc brakes.
Replaces the protective top cap on Dexter 12,000-lb hydraulic jack add-on with selector valve; keeps internal components shielded from debris and moisture.
This replacement inner member slide easily fits into the existing housing of your Dexter XR84 or Legacy UFP surge brake actuator. For use with single or tandem-axle trailers with hydraulic disc brakes.
Replaces the "D" washers, retainer nuts, and hex nuts needed to secure the brake hubs on your Dexter trailer axle manufactered after June of 2002. Includes 2 "D" washers, 2 retainer nuts, and 2 hex nuts.
Restore the performance of your Fortress oil cap with this complete service kit. Includes rubber plugs, oil fill plugs, and O-ring seals to prevent leaks, maintain pressure, and keep your hub looking squeaky clean.
This replacement inner member slide easily fits into the existing housing of your Dexter A-84 Series or Legacy UFP surge brake actuator. For use with single or double-axle trailers with hydraulic disc brakes.
Upgrade your boat trailer's braking power with this rust-resistant GalvX disc brake. Kit includes 1 pre-greased hub, inner (L68149) and outer (L44649) bearings, rotor, caliper, mounting brackets, and lug nuts.
Your Fortress bolt-on cap has been holding it together - now it's time to return the favor. This service kit gives your Fortress cap fresh gaskets, oil fill plugs, and hardware it needs to stay leak-free and pressure tight.
This replacement inner member slide fits into the existing outer member housing of your Dexter or Tie Down surge brake actuator. Fits actuator models LP80, LP85, and LP8500.
Replace worn or leaking copper washers on your Dexter disc brake caliper. These 7/16" crush washers provide a tight, reliable seal between the banjo fittings and calipers to help prevent brake fluid leaks in your hydraulic braking system.
Replaces the clear green lens on your Stage Series rock light. Can also be used as an alternative to a diffused green lens, or for other colors so go wild! Lens snaps in place for easy installation.
If you're showing up to show out, why not add more color and style to your rock lights with another pair? Set the scene in and around your truck with this RGBW plug-and-play add-on kit. Includes M8 splitters and cables for easy installation.
Make it easy to add more rock lights to your set up with this M8 splitter wire for single-color rock lights. Single female plug splits into 2 M8 male ports. Compatible with all Diode Dynamics Stage Series single color rock lights.
18" Line is most often used to connect your actuator to the rest of your hydraulic system. Brass fittings won't rust and are easier to work with than stainless steel. 90 degree bend on one side puts less strain on the rubber line.
This XL acorn lug nut offers the same secure, rust-resistant fit as the standard version, but with extended height for deeper thread engagement. The closed-end bulge fits tight, while the chrome finish fights off rust and grime for the long haul.
Need a tough, reliable connection from your caliper to the main brake lines? The non-stick polymer core locks in pressure, while braided stainless steel fends off road debris. No ballooning, no leaks, just reliable stopping power.
Need a tough, reliable connection from your actuator to the main brake lines? The non-stick polymer core locks in pressure, while braided stainless steel fends off road debris. No ballooning, no leaks, just reliable stopping power.
240" Line is most often used to connect your actuator to the rest of your hydraulic system. Brass fittings won't rust and are easier to work with than stainless steel.