Part Numbers: TLF2021,TLF3008
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there.
Features:
If you're looking for the best tie-downs for your camper, frame-mounted is the way to go. The frame is the most solid part of your entire vehicle, so it just makes sense to attach your camper to something that's not going to warp, bend, or twist. Even more importantly, the camper's center of gravity will sit lower and its weight will be spread across the entire bed. This avoids a top-heavy load perched on top of your bed rails that's liable to sway and get pushed around by crosswinds. The camper's not going to shift or slide around while you drive; it's going to stay put, and your truck is going to handle just like it does without a camper.
Quick Tip: If you have a plastic or spray-in bed liner, it's important that you use a rubber mat under the camper to eliminate any sliding or bouncing.
Frame-mounted tie-downs are also a great pick for preserving your truck's good looks. The brackets install on the frame, tucked nearly flush with the underside of the vehicle. Remove the arms from the brackets when you're not hauling your camper, and the brackets will be barely visible.
Completely custom to your vehicle, the tie-downs attach to exisiting holes in your frame so that there's little to no drilling and no need for any modifications. Because they're custom, you'll want to use our in-house application guide to make sure you get the exact right model. The tie-downs you need might be different depending on what type of hitch or other accessories you have.
Once the tie-downs are installed, use a set of turnbuckles (sold separately) to secure the camper to the tie-downs. The shank on each arm has 2 pin holes so you can choose how far out they extend, that way the turnbuckles can reach the anchors on your camper without making contact with your truck. Tighten the turnbuckles to the correct level of tension (not too tight!).
Make sure the anchor points are offset from the tie-downs instead of lined up with them so that they will hold your camper from multiple angles. This is important for keeping your camper from shifting. Two holes in the attachment plate of the tie-downs let you find the best angle for you camper anchors.
Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there.
Features:
If you're looking for the best tie-downs for your camper, frame-mounted is the way to go. The frame is the most solid part of your entire vehicle, so it just makes sense to attach your camper to something that's not going to warp, bend, or twist. Even more importantly, the camper's center of gravity will sit lower and its weight will be spread across the entire bed. This avoids a top-heavy load perched on top of your bed rails that's liable to sway and get pushed around by crosswinds. The camper's not going to shift or slide around while you drive; it's going to stay put, and your truck is going to handle just like it does without a camper.
Quick Tip: If you have a plastic or spray-in bed liner, it's important that you use a rubber mat under the camper to eliminate any sliding or bouncing.
Frame-mounted tie-downs are also a great pick for preserving your truck's good looks. The brackets install on the frame, tucked nearly flush with the underside of the vehicle. Remove the arms from the brackets when you're not hauling your camper, and the brackets will be barely visible.
Completely custom to your vehicle, the tie-downs attach to exisiting holes in your frame so that there's little to no drilling and no need for any modifications. Because they're custom, you'll want to use our in-house application guide to make sure you get the exact right model. The tie-downs you need might be different depending on what type of hitch or other accessories you have.
Once the tie-downs are installed, use a set of turnbuckles (sold separately) to secure the camper to the tie-downs. The shank on each arm has 2 pin holes so you can choose how far out they extend, that way the turnbuckles can reach the anchors on your camper without making contact with your truck. Tighten the turnbuckles to the correct level of tension (not too tight!).
Make sure the anchor points are offset from the tie-downs instead of lined up with them so that they will hold your camper from multiple angles. This is important for keeping your camper from shifting. Two holes in the attachment plate of the tie-downs let you find the best angle for you camper anchors.
Average Customer Rating: 4.7 out of 5 stars (3119 Customer Reviews)
Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there. Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there.The package arrived very quickly and intact. I have a 2020 Ford F250 SD Lariat short bed with a factory hitch. The tie-downs were really easy to install although the hitch adapter plate (see attached photo) which is supposed to attach to the end of the tie-down would not fit inside the tubing on my factory installed hitch so I installed without it and it is tight and snug
Received torklift tie downs for 2017 F350. Arthur at e trailer. Com was professional and walked me through the ordering and best install methods. Greatly appreciated. Will be ordering from these guys for my rv needs. Thanks guys at etrailer.com
Great product, installation took about 2 hours. Videos were helpful in explaining the sequence of install
This is my second set for the TorkLift tie-downs, and I would not use any other type. We use it daily; our camper never comes off as we are constantly on the move. In the event we have to remove it for vehicle service such as alignment, it is easy to remove and get back on.
The product was easy to install, a bit awkward with only one person on the front tie downs but if you had an extra set of hands then that problem would be solved.
The top bolt hole on the front passenger side was out by about 1/8" but I resolved that by being able to get a drill on the inside of the frame and drilling through that way to allow the bolt to go through both truck frame and tie down. If it had been on the driver's side then it may have been an issue with the gas tank in the way. All is now installed and ready to go,
There great, fronts bolted up perfectly, the rears I hah to do a lot of grinding on the bolt on square plates to make em slide in the factory hitch almost a 1/8 inch all around…
Torklift makes a top quality product. Installs easily once you understand the instructions. Very solid frame/hitch mount, never have a concern about them flexing or breaking. The second set I've purchased (the first set were sold with the truck they were installed on).
Delivered fast. Way easier to install than I expected. Video plus instructions made it easier to understand. They fit perfectly.
Sturdy and convenient to use, but the powder coat finish has proven to not be very durable or able to withstand typical on-road use. I think other owners may have experienced the same. I would have expected a better finish.
Installed on 2020 F250 Superduty. Easy to install rear tie downs only took about 45 minutes. I love the fact there is no drilling or moving existing things. Just straight bolt on and seem to be rock solid.
Great solid product and easy to install. Solution to your upgrade to a dually for the truck camper.
They have worked great. From Michigan to Alaska and back, no problems! They were easy to install and would recommend them to any truck camper owner.
They have worked great. From Michigan to Alaska and back, no problems! They were easy to install and would recommend them to any truck camper owner.
Very well built. All of the hardware needed was included. Good fit. Bolted right on. A little pricey but worth it for good quality.
Had these on two different vehicles. Good product.
Installed these on a 2022 F450. Installation was straight forward. The wire used to locate the bolts from the interior of the frame worked well (very clever).
The bolts needed to be installed loosely due to some distortion due to welding...The bolts were then torqued to value.
This is my second set for a second truck camper.
These really are such a great product! Easy install and excellent durability after a year. Have put several thousand miles on the truck with the camper and couldn’t be happier!
Super easy to install. I had a bed step mounted and had to remove it to install these, which is kind of a bummer, but not a deal breaker!
The torklift products are excellent as always and customer service from etrailer is some of the best on the web! They are my go to source for all things truck camper.
Fast shipping and had the Torque camper tie downs mounted within a week. I will use these guys again.
The frame mounted front tie downs are as good as expected. They bolted on fairly easily with some fishing of bolts through existing frame holes. I have a F250 supercab/long bed with wheel to wheel running boards. Both Torklift and eTrailer websites said the tiedowns would fit with my running boards but they didn't. eTrailer did offer to pay to return the tie-downs but I chose to keep them. I was hoping for a discount on new cab length running boards for my troubles but they would only offer 5% so I skipped that and modified my existing boards myself. I'm going with 4 stars because of the confusion on the web site and a few typo's in the instructions but the tiedowns are very nice.
These parts fit exactly as specified with no modifications necessary. It took me a couple hours to install by myself, another pair of hands would have sped up the process but it can be done alone. They hold up well and when not in use I store the extensions in the garage and the receivers are almost hidden.
Installation is about 5 minutes...they install in the sides of the receiver tube.
No problems.
The Package arrived on time and all was correct. It was easy to track the order through the shipping process, I found the staff easy to work with and they appeared to be genuinely interested in providing good service.
Rick B.
11/25/2022
Torklift tiedowns are working great, great fit, no problems with install.
It fits but you have to force it into place on a 22 f350 CCLB. The top mount that ties into the bed mount sits too low on the driver and passenger side. Not quite a "exact fit" like advertised. Pictures of both the driver and passenger side added.
Ask the Experts about this Camper Tie-Downs
Do you have a question about this Camper Tie-Downs?
TorkLift Accessories
Fit to this rack on your 2021 Ford F-350 Super Duty
Info for these parts were:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Ford F-350 Super Duty Accessories
Heather A.
10/12/2022
Thank you for your photo. Torklift does recommend to use the hitch adapter for the 2020 Ford F-250. The adapter does need to be turn horizontally to fit inside the hitch not vertically.