Features:
Bring the convenience of your kitchen sink to the trail with this camping sink. Easily fits into cutout on countertop and collapses for storage. Easily folds into the storage compartment on your MORryde camp kitchen (MR83MR - sold separately).
More Information >Features:
Bring the convenience of your kitchen sink to the trail with this camping sink and faucet. Included pump provides water from an on-board source. Easily folds into the storage compartment on your MORryde camp kitchen (MR83MR - sold separately).
More Information >Videos
for Jeep Storage
Help Articles
for Jeep Storage
Expert Answers
for Jeep Storage
We recommend that all trailer tires be inflated to the max psi stated on the sidewall of the tire. If the tire is under inflated, the weight capacity is lowered to an unknown amount for that tire. Although running lower air pressures can improve…
view full answer...I do have an option for you but I cannot advise you combine two hitch adapters together like the Roadmaster Hitch Extender part #RM-071 and the Roadmaster Dual Hitch Receiver Adapter part #RM-077-4 as this would be very unsafe. However, if you need…
view full answer...The best way to improve the handling and stability of your 2011 E-450 motorhome is going to be with a rear sway bar upgrade like the Hellwig part #HE78RR. This will make the biggest difference and honestly should be the first thing anyone with a…
view full answer...The Yakima EXO Swing Away Enclosed Cargo Carrier for 2" Trailer Hitch #Y62VR may or may not cover your tail lights and license plate. If it does, you can add the License Plate and Tail Light Relocation Kit for Yakima…
view full answer...In regards to the Roadmaster Exact Center Steering Stabilizer part #RM47MR, the stabilizer installs on the front of the steering arm pointed down. I have attached a photo of this below. If this wasn't what you were…
view full answer...Both the LED Trailer Mini Clearance #MCL10AKB and Uni-Lite LED Clearance #MCL11RKB will require an 11/16" hole for mounting. These both use the same Grommet #A11GB.
view full answer...The Hellwig 7180 is our part number #HE78RR and the part 7718 is the part #HE26GR which I have confirmed fit your 2015 Tioga Ranger 31D on a E-450 chassis. I sent an update to have the instructions fixed.
view full answer...To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328…
view full answer...If you are just looking for a new converter, the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers part #PD4635V will be a direct upgrade for the Magnetek Converter Series 6300 Model 6332 that you have now.
view full answer...Although most Class V hitches use a 2-1/2 by 2-1/2 inch receiver tube, some like the Curt #C15410 use a 2 inch by 2 inch receiver tube. Before proceeding, you'll need to confirm which you have. Then,…
view full answer...We do carry the Blue Ox base plate kit BX1146 but we changed the part number on our site to #BLU47XR so this is available and what you are looking for to flat tow your 2021 Jeep Grand Cherokee L Summit. Then for a diode taillight kit like you are…
view full answer...The square tubing of the Replacement Back Plate #SPN550 that you referenced is 1-1/4 inch by 1-1/4 inch. (See picture). Chances are your cargo carrier is designed to fit IN a 1-1/4 inch hitch and not around a 1-1/4 inch shank like what this product…
view full answer...