Hey Ron, great question! The Coleman-Mach Underbunk RV AC #CM82RR vents the heat through the floor. Installation requires creating openings in the floor for air flow, heat rejection, and also for the drain pipes. See the attached photo. The #CM62RR…
Hi Angela; you will run air ducting (not included) off of the openings on the side of the Coleman-Mach Underbunk RV AC #CM62RR. I recommend getting the All-In-One kit #CM82RR which includes all of the accessories you need for installation. The unit…
Hello Geoff, thanks for reaching out. The closest thing we have to that would be the Better Bath RV Kitchen Sink #LC421572. This is 25" long x 15" wide overall. The interior of the sink is 22-7/8" x 12-7/8". Do you have any…
Hey Mike, congrats on the new trailer. The Tire Linc Pro TPMS for RVs and Trailers item #LC77VC is the Lippert TPMS Prep. This is just the aftermarket version of what gets installed on newer trailers. It includes four sensors that mount to a trailer…
For a 25-3/4" x 14-3/4" cutout we have the following single bowl and double bowl options: Single Bowl: Better Bath RV Kitchen Sink #LC385313 Double Bowl: Better Bath RV Kitchen Sink #LC388412 Better Bath RV Kitchen Sink #LC385314 LaSalle…
Hey Jeff, Depending on how much clearance you need from that tailgate is going to determine what kind of hitch extender you will need. Assuming you just have a factory 2" hitch receiver on your Ram you could go with the hitch extender #e48YR…
Hey Michael! Since you were looking at the SoftStartRV Soft Start #SSR54FR are you wanting that built in as well? The Active Controls ActiveStart Plug-In Soft Start for RVs #AS94FR is a soft start and surge protector all in one. If you aren't…
Hey Ron, great question! The new PowerMax stand-alone converters like the 45A #PM34VR, 55A #PM94VR, 60A #PM44VR, and 100A #PM84VR give you three selectable charging modes so you’re not locked into one charging behavior. 3-stage mode factory default:…
Hey Chris, No, there isn't an upgrade kit for your Generation 1 MORryde StepAbove RV Steps to make them a Generation 2. There is a Replacement Leg for MORryde StepAbove RV Steps - 2nd Generation #MR36DR, but because the Generation 1 steps'…
Hey Tyler, yes, as long as your factory jounce bumper and bracket are still in the original location, the Firestone air bag kit #F64XV can absolutely fit your lifted Silverado. You’ll just need the right Firestone spacer to restore air-spring height.…
The Lippert Replacement 500:1 Motor for Electric In-Wall RV Slide-Out System, #LC287298 is the proper replacement part for Winnebago PN 181862-01-700 and is considered a high torque replacement motor. If your 2014 Itasca Solei 38R was built with the…
I received this order yesterday. Thanks for the outstanding service. I appreciate it! Thanks, Alex
Alex
Blowing Rock, NC
JR Products RV Sinks for easy upgrades
Built from molded plastic, JR Products RV sinks help keep weight down. Choose the white or parchment look that fits your space, then confirm compatibility by matching details like a 1-3/8" drain opening and a 4" center-to-center faucet layout where applicable. A simple way to refresh your bathroom without extra bulk.
JR Products RV bathroom sinks are made from molded plastic. This helps keep weight down and they're sized right for tight RV bathrooms. Check the color—options include white and parchment. If you want a metal look, confirm finish options first since stainless steel wasn't available in the smaller sizes called out.
They typically secure with corner studs, clips, and wing nuts, and seal with silicone. Dry-fit first; access can be tight once the sink is in. If no paper template is included, flip the sink upside down and trace the cutout. Run a bead of clear or white silicone around the rim to help prevent water from getting under the lip.
Select JR Products bathroom sinks use a 1-3/8" drain opening and include a rubber stopper that can sit slightly above the drain or press in to plug. Verify your existing drain size before reusing parts. If you prefer a lift-style stopper, plan to swap to a compatible drain assembly for that opening.
Yes, JR Products bathroom sinks use a 4" center-to-center inlet spacing on certain models. Measure your faucet and sink inlets to confirm the 4" spacing matches. If you're swapping faucets too, make sure the new faucet's inlets line up with the sink's holes before tightening everything down.
Filters
