# 1
Curt Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-1/4" Long - 3,500 lbs
I would give five stars but due to what looks like packaging problems the hitch came very marred and the coating chipping off.
Good and strong but not a great angle/height for my application so had to go to a straight line fit.
# 2
Draw-Tite Drawbar for 1-1/4" Hitches - 5/8" Rise, 1-1/4" Drop - 7" Long - 3.5K
Items packed well delivered on time. Doesn't get much better that that.
The service is great and so is the price. Box came damaged but if it installs as easy as the last one I bought from etrailer I will be very happy!
# 3
Curt Class II Euro Style Drawbar with 2" Ball - 3-1/8" Rise - 3,500 lbs
Incorrectly listed on etrailers as a 3-1/8” rise, when really this is a 5-1/8” rise (marked correctly on the item itself, but listed incorrectly on this website).
I am completely satisfied with the product. Great quality and excellent finish. Prompt shipping and excellent customer service. It is stylish and functional and will meet my needs for towing up to 3,500 pounds. I would definitely do business with this company again!!!
# 4
Curt Class II Drawbar - 3-1/8" Rise - 11-1/4" Long - 3,500 lbs
Used on my 1999 Dodge Intrepid's CURT 12006 Class II 1.25 in. Receiver Hitch: 350lbsTW/3500 lbs GTW. I use this Curt Class II Drawbar - 3-7/8" Rise - 11-1/4" Long - 3,500 lbs to tow a 3,500+ GTW dual axle trailer. I have used it with the trailer FULLY loaded and it performs EXCELLENT. You have to make sure the trailer is loaded correctly so as not to put too much down force on the tongue/drawbar. I was skeptical that the SOLID 1.25" bar would not take the load, but it is super strong. I chuck it in the trunk when not in use to protect passerby's shins, but it sticks out far enough clear the Intrepid's bumper, and is solid with a 2" ball (required a bushing). etrailer got it out fast at a good price! I would totally purchase this again from them.
Every part excellent quality. Perfect fit, all parts were exact for my vehicle. Watched the video on youtube for wiring and being a mechanic for over 50 years was able to connect signal lights all from driver side of harness. Instead of leaving plug inside trunk I wired through the rubber outlet to the back of the hitch ready for use. Very happy highly recommend etrailer.
# 5
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Drawbar looks great and will be using in next two days. Thanks!
# 6
Curt Class I Drawbar - 5/8" Rise, 1-1/4" Drop - 6-3/4" Long - 2,000 lbs
I wrote 2 days ago and haen't heardafom anyone so I guess you only want reviews-. Here is what I wrote Steve, the class 1 hitch doesn’t fit the trailer hitch either. I don’t understand the continuing problem with all of the Curt hitches we have tried including the last draw hitch you selected and shipped, which I now need to return after H. Idalia passes, I want to point out that I initiially ordered somewhere on line a Maxxhaul adapter so I could move my 2” trailer until I sell it and it fit perfectly. I NEVER expected to have so much trouble getting a ball hitch to fit the 1.25 hitch recommended by etrailer for my car. Aren’t you glad I am writing an email rather than make star comments? I know that someone writes these things for ‘you’ and you don’t necessarily do the hands on so please direct this problem to someone who is supposed to make these product directives and solve this $[XX] attractive trailer hitch problem so I can haul my lawnmower in for repairs when needed on my utility trailer designed for doing so. Doesn’t Drawtite have a ball hitch for level hauling a trailer rather than Curt which is too thick. The powers that be need to rethink OD (outside diameters) vs ID (inside diameters) in their trailer connectors, screw the rattling! PS don’t forget arrangements for the return of the recommended draw hitch.
Great price! Amazingly fast service! The drawbar was a very tight fit in the hitch until I scraped off some of the paint at the end; then it was perfect.
# 7
Curt Class I Drawbar - 5" Rise - 9-9/16" Long - 2,000 lbs
For Mazda CX-3 owners, this is the drawbar you need to achieve the correct final hitchball height for small U-Haul cargo or motorcycle trailers. You know the receiver sits quite low so this gets the height just where it needs to be, especially when the trailer is properly weighted/loaded.
Shipped in quicker than I thought it would. It fit it my old Hidden Hitch Class I receiver perfectly. I drive a '97 Geo Prizm, and the 5 inch rise is a definite plus in keeping my 5 x 8 utility trailer nice and level when I'm hauling lawn equipment. The only drawback is that the Curt drawbar does not come with the pin.
# 8
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.
Purchased for a Hyundai Elantra. After a 2" ball is mounted, there is about 7.5" from the top of the square shaft to the top of the ball. This is what was needed to get the center of the ball 18" off the ground for most U-hual trailers. This design has no plate edge protruding below the square shaft. This helps reduce scraping when going over bumps, which is an annoying issue with my other ball mount. I would have much preferred the euro ball mount, which has a nice 45' bend to avoid scraping, and a ball that will never vibrate loose, but one was not offered with this much rise. The ball mount is well made of solid steel, not a hollow tube. Finish quality is excellent. The mount does not come with the locking pin needed and so that must be ordered separately with the ball. Item was packed a little loose in the box and was clanking around with the other item I bought, but they did not get scratched up.
# 9
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 9-3/8" Long - 3,500 lbs
I needed to tow a trailer with a 2" ball. My original ball mount has a 1 7/8" ball installed. I had previously tried to change a ball on a hitch and destroyed the nut and damaged the underside of the ball mount. The lock washer had done a great job in keeping the nut from coming off. I dreaded trying to remove my 1 7/8" ball to install a new one that I would only use once. I decided to buy a new ball mount and mount the new 2" ball. This ball mount is so inexpensive that I realized I could have both ball sizes permanently mounted for use in either ball size.
I wasn't sure what type of ball mount I needed for my new Mazda CX-9, so I had to call a representative. The first time I called, the very knowledgeable gentlemen told me exactly how to measure my SUV to figure out the drop I needed. I called back the next day and talked to a lady who helped me figure out exactly what I needed. This is my second purchase from etrailer. The first was a hitch for my old Honda Odyssey, which was also a great experience. The employees are so helpful, the video tutorials on the web site are fantastic and the prices are great. etrailer.com is the first place I go to look for trailer and towing supplies!
# 10
Drawbar for 1-1/4" Hitch - 2-5/8" Rise, 3-1/4" Drop - 7-3/16" Long - 3.5K
The hitch works great. The service was excellent!!! I'm going back and having a hitch put on my other car soon. Thank you.
Everything was perfect.! Nice paint, package, and fast shipping.! Im satisfied.!
# 11
Curt Class II Euro Style Drawbar with 2" Ball - 2-5/8" Rise - 3,500 lbs
It isbthe right size and helps with the height difference to make the trailer more even with the back end of my Accord.
Look and quality of the mount is awesome. Beefy in size as well. If using on my particular application, removal of rear diffuser is necessary. If they had extended it another inch it woulda been perfect. 2015 Audi a3 tdi. Wouldn’t let me add a third pic but it’s a finger tip space between the ball and bumper with diffuser removed.
# 12
Curt Class II Drawbar - 5" Rise - 11-5/8" Long - 3,500 lbs
I was in need of a hitch higher than the standard 3 or 4 inch riser and spoke with Samatha B, after a couple of emails she found a 5 inch riser for my 1 1/4" receiver. Just what I needed and a happy customer. Received very quick and good sturdy quality. Thanks again!
3.5 stars. Product looks like it should perform as advertised, but it arrived with several chips in the paint. This is most likely due to improper surface preparation and cleaning before the powder coat was applied. As you can see in the photos, there is already some surface rust on some of the areas, including the hole for the hitch pin. Ultimately the paint will get scratched up from use, but it would be nice to see some extra attention to detail from the factory.
# 13
Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-3/4" Long - 3,500 lbs
Easy ordering, fair pricing, prompt delivery...product arrived in excellent condition, very heavy duty drawbar for use with by 4ft x 8ft medium duty trailer.
Solid quality and workmanship.
# 14
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 9-3/4" Long - 3,500 lbs
This draw bar in perfect for my John Deere X738 tractor. What I like about it is the ¾” rise it keep the draw bar height at about the same as the factory frame so the attachments height remain level. Thanks for the great product.
Not much you can say about a bar with a piece of flat metal welded to it; well made looks good. What is really important is that e-trailer is fast, friendly and knowledgeable. I've ordered from them anytime I needed a trailer/RV part.
# 15
Curt Class II Euro Style Drawbar with 1-7/8" Ball - 2-3/4" Rise - 3,500 lbs
Very nice product! Appears like the European models. That is what I was looking to obtain. Will be used for show on my 1957 Triumph TR3.
100's of miles on it and all is well.
# 16
Brophy Drawbar for 1-1/4" Hitches - 5-1/2" Rise, 6" Drop - 7-1/4" Long - 3.5K
I just purchased a new hideaway hitch system. But the hitch sits only 15 inches off the ground at best. And, my trailer coupling is 22-23 inches off ground. So l needed 7-8 inches of rise on the new 1.25 inch receiver system. Internet research took me to etrailer and the Brophy hitch. I got 5.5 inches with the Brophy hitch, the highest available for a 1.25 inch receiver I could find. The others are limited to 5 inches max. I added another 1.5 inches with your Curt shock absorbing hitch. Voila, with a combined 7 inches of rise and on level ground the trailer now rides perfectly level!!!! Both parts were very easy to connect. Delivery was speedy. Thank you for saving the day and my investment in an expensive new hideaway hitch!
Quality parts, but the extra rise with this and the Curt Rocker Ball still wasn’t enough to avoid scraping the top of my inclined road while towing my boat.
What our customers are saying:
"very easy to shop"