Most Popular 10000 lbs GTW for Jeep Wrangler Unlimited

Hello The hitch works great as viewed in the enclosed pictures. If inverted it hits the bumper, of my Dodge 2500. The section that goes into the receiver is about 1/2" too short and hits the bumper. I have not tried it on my other vehicle to see if this is a problem. Kind Regards Leon D

Click to Enlarge

A VERY nice piece that will set your mind at ease. Easy to adjust height. The ONLY thing I wish is there was an option to have different sized ball combinations. I mainly use 2" and NEVER use a 2 5/16"(or whatever the larger size is) and would prefer to have a 1 7/8" on the other side.

Click to Enlarge

Picked up my teardrop in ABQ on 2/17/23, and the Curt ball mount lined up perfectly with no drop/rise, and the extra length gave clearance for my rear door mounted spare tire. This mount is a beast, and the "overbuilt" nature of it gave me confidence that my Bronco would tow the teardrop easily. I also got the Curt Echo wireless brake controller, which synced easily to my phone and was easy to install, set up, and use. Overall a great towing experience, thanks to etrailer and Curt!

Click to Enlarge

Very versatile - can use it on both my vehicles that have very different hitch height. Clean welds, super solid. Weighs a LOT!

Gone are the days I need to carry three different hitches with different sized balls on them. Gone are the days when I, or others, walked around the back of my truck and cracked their shin on a protruding trailer hitch. I keep this folded up in front of the drop where it's not going to catch anyone by surprise. When I'm ready to use it, I simply pull two pins out which allows it to drop free and rotate out. I choose the height I need and install the two pins/clips. To rotate the balls, again simply pull the third pin and rotate to desired size. It was more than I wanted to spend at the time but since I'm glad I spent the money.

Click to Enlarge

Click to Enlarge

Super convenient and well worth the money. All 3 of my trailers have a different ball size, and this is a breeze compared to constantly swapping tow hitches. Keep the pins well lubricated, and they slide well maintain their appearance.

Slightly longer, so you can open your tailgate with a cargo trailer attached. Trailers with a tongue jack that is forward are problematic for tailgates...

I’m pleased with the product and how prompt the delivery was. However the packaging was insufficient and the packaging was torn open all over. Scuffing of the finish is a result and of little consequence due to the intended use. It’s a stinger w/ball for motorhome. May I suggest better packaging in the future

Click to Enlarge

The 3” drop is perfect for a stock 4x4 Silverado 1500. I can tow my small trailer as well as my full size tandem axle trailer without changing hitches/balls. Just what I wanted.

Click to Enlarge

Click to Enlarge

Love being able to have access to both 2" & 2-5/16" balls without having to haul around 2 hitche's and then the height may not be right. When I'm not using I can leave it or stow it with very little effort.

Nice high quality product. I got the 9” trip for a 2017 Tahoe. Worked great for a 16’ enclosed

Click to Enlarge

Very impressed! I trailer everyday and and have trailer with both ball sizes and one is a low-rider. Could not be easier!

Very strong, easy to install and very secure. Yes a bit pricey, but well worth the money. I did notice there was what I thought was an unusual amount of play in the receiver. I called etrailer and Marcia was so very helpful and very concerned that I may have received the wrong product. She even called the manufacturer and found out what the changes that were made by the manufacturer which made the pictures incorrect. My hat is off to Marcia and all the folks at etrailer

Click to Enlarge

ball mount fits loosely in the receiver so that the pins that extend out from the ball mount shaft through the holes in the receiver don't extend out far enough, for my liking. This is because since the ball mount shaft has so much play, it will shift to one side. Then, the pin on the other side does not extend all the way out of the hole so that it is not flush. True, i am being paranoid. However, i imagine a case like a crash where enough force could pull the shaft out from the not fully extended pin side to release the trailer to wreak more damage. I would just feel more secure if the pins went out further through the receiver or the shaft was not so loose. Otherwise, i really like the product a lot... enough to give it four stars... :o)