Most Popular Load Assist for 2022 Honda Civic

The product is of good construction but probably due to how it fits on my crossbars it needs additional support. The crossbars for my Honda Pilot are wide blade type and these racks seem more appropriate for narrower square type crossbars. Even with the rack fastened very tightly, the rack can twist back and forth. Last year on a trip across Montana the wind was pretty gusty and it caused the front one to pivot quite a bit and we had to pull off and apply a ratcheting strap over the kayak and under the factory rails to ensure it was held tight and wouldn't move again. This year on the same trip we had bad winds but had a roof rack mounted behind these racks giving it support on the tall side. We had to strap it real good to make sure it didn't move. If we hadn't had that additional support behind it and add'l straps we probably would have had more problems. I think if the top metal bracket had a wider channel to fit our crossbars it would be much more stable. The way it is now it just sandwiches 2 metal plates between my crossbar which allows it to pivot under stress.

Click to Enlarge

Loved the racks, seem very durable. Only downside was that the groove made for the crossbeam was quite a bit smaller than my crossbeams, but they still secured down great. You'd have to have a pretty funky set-up for these racks to not work on your vehicle. Having all the straps/tie-downs included was awesome too. Reccomend!

Click to Enlarge

I installed these as soon as I got them and I’ve got to say, there are some extra holes for screws that are a tad misleading and the pieces that secure it to the cross bars don’t seem super secure. For reference, I do have Rhino Rack’s vortex crossbars so this should fit snug. The rubber tops were tough to get into place and I am worried they’ll snap when I go to remove my rack but Rhino Rack has yet to fail me with their products so I bet it’ll work out great!

Click to Enlarge

This is a great product. As a novice kayaker I was nervous. The assembly was easy with clear instructions. My sales professional Crystal K. was a pleasure to work with. She knew the answers to all my questions. From placing the order to the delivery I am very satisfied. I will be using etrailer again. I can't wait to get my kayaks to the water.

Click to Enlarge

Click to Enlarge

It’s very sturdy and easy to use. However, I’m concerned as it could be stolen easily.

First experience with purchasing from etrailer. Absolutely felt that my order was personalized which is a nice touch. The Rhino Rack S512 folding JStyle Kayak holders arrived boxed impeccably with no damage whatsoever and the price was great! Fantastic first time experience. Looking forward to using them. Thank you.

Click to Enlarge

The product seems great but I have not figured out how to get it safely attached to my bars. I have an Agricover Adarac on the bed of my truck and the crossbars are 1-1/2 x 1-1/2 inches square. I thought this would work well since it's for up to 3-1/2 x 1-11/16" crossbars, but it isn't secure on these. I'm going to try and figure out an alternate method for attachment though. Thule Hull-a-port Pro's are the perfect (mounting) solution but don't seem to be made any longer.

Click to Enlarge

Great product and great customer service! Very easy to install, but I highly recommend to watch the installation video first. We used typical black office clips to clip the excess straps down since they came untangled when driving. Also, I recommend to purchase locks for the racks since we are concerned someone may steal them because they are so easy to take on and off.

This product is excellent. I have transported my kayak on these J Hooks several times going 70+ mph down the highway. It never moves. The bolts that come with it are short. If you have a thick roof rack, you will need longer stainless steel bolts. Make sure you you orient the blue straps with the buckle on top so you can pull down to tighten it up.

Click to Enlarge

I think the Thule Hulaport kayak racks are the best, most secure way to transport your kayaks. I had these on my Xterra and hauled two kayaks up to Cape Bretton park in Nova Scotia, Canada from Connecticut, USA no problem. We were even able to store gear in the kayaks for the trip. I’m so excited to have them for my Crosstrek. Highly recommend these!

Click to Enlarge

After attempting to mount the individual rack pieces using the “burglar proof” button head screws with the pin in the recess and the short hex wrench with the hollowed out end I discovered that no real burglar would want the rack but would rather have the kayak so the first thing I did after spending 10 minutes trying to insert the hex into the button head screws with the pin inside the recess and attempting to turn the bolts and continually being obstructed by the support pieces and the paint interference on the bolt heads with trying to get the wrench into the recess I knew it was going to be a long frustrating process so I threw them away and purchased new button head stainless steel bolts and a 4mm extended handle hex wrench to turn them. Smartest thing I ever did. You not only have to mount the rack initially but then you have to put the kayak on the roof and remount all pieces again to fit your boat. All kayaks are different to one degree or another. Having to move the individual support and retighten them with the boat on the rack is even more difficult to do than the initial mounting with these “burglar proof” bolts and hex wrench and you will be happy you threw them away before you started the entire process. Try it for yourself at first and then go get the alternate ones. Worth the little investment and stainless steel will not rust away when you want to remove the rack system in the future. Once the rack is on your vehicle and kayak in rack the tie downs supplied are very good quality. Make sure you use the recommended tie down locations and directions, two kayak body ties and ties at front and rear. Due to numerous kayak hull designs it would be nice to have each support pod have a horizontal swivel built into it so it readily conforms to the hull shape. The overall quality of the system should be the last rack you will have to purchase. I only had issues with the supplied bolts and hex wrench. I gave this rack system a three star because of the bolts and hex tool and the individual pods not swiveling and I haven't at this point transported the kayak anywhere so I am waiting to see how it handles long trips with wind loads and constant loading and unloading performances.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Works great. I’m 5’6” and the pivoting cradles make for easy loading and off loading. I do need a stepping stool to install the carrier on the roof rack.

We needed a better way to haul around 3 kayaks and after looking at a number of options, we settled on the Thule Stacker setup. Installation is simple and the stackers provide a sturdy option for hauling multiple kayaks. One of the best features is that they fold down when you don't need to use them. My shopping experience with etrailer was smooth and shipping was prompt.

Click to Enlarge

My wife uses these to carry two small kayaks in the roof of her Subaru. They work great and we very happy with the purchase. She also likes finding her car easier in the parking lots, even with the carriers folded down.

Click to Enlarge

Works perfectly. I didn't feel like spending a lot of money on a roof rack at this point in my life so this fits the bill. The roof on my Honda is a little weak so it buckles when I go over big bumps, just take it slow.

It's doing the job of securing my kayak to my rackless prius, at a fraction of the cost. However, the instructions included along with the straps did not work for me. I spent a considerable amount of time adjusting things: the red straps that are supposed to go over the boat and secure on the bars were not long enough. The blue straps are much longer, so I am using the red straps to secure the bars to the car, through the open doors and cinched inside the car. I am using the blue straps to reach over the boat, and I decided to feed those into the car too- feels more secure than to attach them to the bars on top. The black straps for front and back strapping don't work for my car in the way shown, I had to jerry-rig. Overall I have figured out how to make it work, and I'm glad I didn't spend $xxx.xx on a serious rack system.

Click to Enlarge

I did a bit of testing to figure out how long it would take for the vacuum to loose pressure. I left the racks installed over night following the installation instructions and when I checked on the sucking cups the next day, there was one that needed to be pumped twice, but outside of that all of them were holding on nice a tight. After strapping up a 12.6 Slingshot Nitro Standup Paddle board and driving an hour up the road. Everything held up perfectly. I did not exceed 55MPH on my way up just to make sure all was well. On my way back I went up to 65MPH and no issues. I would recommend having a none lint cloth with you to clean the surface and the suction cups prior to re-installing the SeaSucker back onto the car roof. Overall, very confident in it's ability to hold the board in place and not have extra hardware to install permanently on my Rover!

Click to Enlarge

I have only used the product twice but it works as advertised. Very easy to install and remove. Great service from ETRAILER. I finally have a solid surf rack on my 2014 beetle.

Click to Enlarge

Click to Enlarge

've previously used the Yakima Kayak Stacker (old style), which worked fine but I always worried the straps would slip off the hook at the top while I was loading boats. They also didn't fold down, so had to be removed after use unless you wanted to look odd and cause a whistle while you drove down the road. They didn't have a universal attachment option, requiring adapters depending on the style and make of your crossbars. More recently I got the Thule "The Stacker", which is a superior solution. You thread the strap through a closed loop at the top, so you don't worry about straps slipping off while you're loading boats. They fold down after use and have a universal style attachment that fits around most styles and makes of crossbars. Good stuff. I really like the straps that come with these, as there is a rubber cover that slips over the metal cam buckle to protect your car's paint while you're tossing the strap over your boats to strap everything in. In order to shuttle our boats for river trips, we needed stackers to fit on both our cars, so it was time for another set. I had never heard of Rhino Rack before, but the lower price than Thile caught my eye, so I read about them and decided to give them a try. The Rhino Rack Nautical Stack used a closed loop at the top, which I liked better than the Yakima or Malone options, and came with the hardware necessary to install them into the C-channel of my Malone aero crossbars, which I wanted to try. I remember that with the Malone stacker, you had to buy the C-channel mount hardware separately. I really like the Rhino Rack Nautical Stack. They are a single post design, unlike the loop style of the Thule "The Stacker". I don't know if this cuts down on vortex drag, but it definitely saves you a couple horizontal inches up where the boats stack. The Rhino Rack Nautical Stack has textured rubber strips on either side of the post, which I believe is intended to cut down on vortex drag, but is also quite helpful in that boats tend to slip much less when you're just leaning them up against the post as you load up before you strap them. That's smart. The Rhino Rack Nautical Stack feels really solid. The mechanism for folding them down and locking them upright is easy to use and feels solid. Installation instructions were good. I tried to install into the C-channels without removing the rubber tubing in my Malone aero crossbars, but couldn't get the little squares to slide into the slots with the rubber tubing in place, so had to cut the tubing, slide the Nautical Stacks into place, then cut down some of the tubing I had removed and replace it in the remaining unfilled crossbar slot. That's not a knock on the Nautical Stack; just a tip in case you're trying to do the same kind of install I did. The one area in which I was less impressed was the tie-down straps that come with this kit. The metal cam buckles have no covering at all, so I'll probably still use my old Yakima and Thule straps instead and use these as backups. But overall, I think these are going to work at least as well, if not better, than the Thule option, and for quite a bit less money.

Click to Enlarge

Click to Enlarge

So much better than the 'C-shape' kayak holders. These things allow you to fit inside a garage, and add up to four kayaks. Very easy to use.

Carry my SUP on my Honda Civic with this on a Thule carrier bars. Has held up well after a year in the sun in Southern California.

I love this rack! I don't think I'll ever take it off my car. Cool and functional. I've used it for my snowboard in the winter and my surfboard and camping gear in the summer.

Click to Enlarge

Very easy to install on roof rack. Just be careful not to lose one of the rubber pieces that help protect your board. They can easily fall off of the rope when tying your board to the rack.

With a little help from youtube, this was one of the easiest things I've ever assembled! LOVE my new SUP rack!!

Click to Enlarge

The Rhino Rack cradles, straps and hardware are all good quality and I have no complaints. The only issue I have, and the reason for only a 4 star rating, is the supplied M6 x 40mm Security Head screws are too long for the factory cross bars on my roof rack. When I first installed the cradles if I had tightened the screws all the way, the ends would have dug into the roof and paint, even before I added the weight of the kayak. In checking, I can purchase some M6 x 25mm Security Head screws from Amazon, but frankly part of me feels that for what I’ve already paid for this kit I shouldn’t have to spend another $15 for the correct length screws, plus the package has 20 screws and I only need 8. However, it appears that is exactly what I will have to do. At least they will be stainless steel, rather than the cheaper material the current screws are. Plus I will have extras for when/if the head strips out. I would suggest Rhino Rack consider included in their kit two sets of screws to meet this need. Keep the length they have, Judy add a set of 25mm. I’m still happy with the purchase but not 100%. I do like how the kayak slides easily on the rear felt lined cradles. Plus Rhino Rack includes every tie down strap that you will need, e.g. one each for the bow and stern in addition to two straps intended to secure the kayak directly to the roof rack cross bars. I would highly suggest you get in the habit of using all four straps, you really don’t need to have a gust of wind lifting the nose and tearing the roof rack off your vehicle. Can happen! My brother-in-law lost his roof rack exactly in this manner. So happy yakking and safe travels down the road. By the way I have paired these cradles with the Rhino Rack RTL002 T-Load Hitch Mounted Load Assist and Support Bar for 2” Hitches also purchased from eTrailer. I’ve attached some photos showing my first and second attempts to solve my dilemma. I need to order the replacement screws. First attempt after dark was a large flat washer, then the next day I added some nuts under the large washer. NOTE: Photos may post in reverse order.

Click to Enlarge

Click to Enlarge

This product was very easy to install. I had it installed in about 15 minutes and my kayak on the roof a few minutes later. The only issue I had was one of the tie-down straps was broken (stitching was not complete or something). Other than that, this product was great! The customer service (Carol and Neil) were great also, helping with the strap problem. Thank you again!

Click to Enlarge

Click to Enlarge

I acquired a second kayak and needed a system to fit the factory racks on my 2011 Toyota RAV4. Etrailer.com has always had information on what fits and has always had the item needed for the job. I attached the Yakima BigStack to the top with ease, and, with one other person to hold the kayaks while I secured, tied two of them down for a long road trip to Northern Minnesota. The system worked just fine. The only caveat was in the configuration of multiple boats in the instructions. The diagram has two boats on the same side of the posts, however, I found it more secure to put one on either side ( other reviews of this product on different Internet sites have found similar results.) The boats made it through the trip with no shifting.

Where do I start? I've been whitewater kayaking for 22 or so years now. I've always used used either Yakima or Thule products... Until I bought a 2015 Nissan Rogue with a naked roof. The curvature of the roof and large door jams mean that Yakima and Thule can't make racks for them. I went to a place that does custom installs and again because of the curvature of the roof, they couldn't give me a rack. This meant no kayaking which is really bad news. Enter the Rhino rack system. I purchased the feet, the fit kit, the cross bars and a Yakima "big stack" stacker. The first issue I had is the reccomended size for the Nissan Rogue is only 48 inches. Way too small too haul 4-5 (very light) whitewater kayaks. I called etrailer and they were SUPER helpful, told me I can buy the 65 in cross bars and they'll work fine. I held my breath and placed my order. I was nervous leaving my trusted name brands. The order arrived super fast (they told me it would arrive by Friday but it actually arrived on Thursday) and everything was packaged rock solid. I was impressed. I read the instructions and put the rack system on my car. It took about a hour (it was hot and I worked slowly) but the rack system is SUPER SOLID. I love it. Rhino might have a "forever" customer out of me. -The rack system is very stable. I can't move it with my hands by pushing or pulling. -The rubber stripping you put on the top and bottom of the bar is an awesome added feature AND it reduces wind noise. -Adding the fairing reduced wind noise even further. With four boats on the roof you couldn't hear any extra noise. The ONE thing I dislike is that you need to use the supplied Allen wrench to take the rack on and off the car. It's a small complaint, but other systems I've used in the past don't have them. I paid much less for this system than I would have if I purchased one of the aforementioned systems, but I'm really really satisfied with the product. We will see how well it holds up over long-term use, but it looks awesome!

These work great and I was able to install them on the OEM rack for my truck. The only downside is that the threads for the clamp hang down a little too close to the roof for comfort.

The Rhino-Rack 2 Kayak Carrier I ordered from etrailer was easily reviewed and ordered from their website and ALL communication relative to order confirmation and extreme detail included in their tracking was nothing short of phenomenal! The items were packaged with care and arrived intact. These fit our basic Lexus crossbars and is the perfect product for carrying our two (2) kayaks. My hat goes off to the great folks at etrailer -- It doesn't get any better than this!!!

Product was as advertised, however it was missing four bolts that I had to get at a hardware store, but other than that it was fine. Service from etrailer team was outstanding.

I've been using the product for two summers now and it is perfect for what I'm using it for. My canoe is an Old Town Discovery 133, it's very wide and I initially had trouble fitting it in the brackets with how relatively narrow my Rav4 is, but the instructions that came with them mentioned I could just flip them around. That worked perfectly. I only use the brackets and the tie down straps from the kit to tie the boat to the crossbars, and then use the painter lines I put on the bow and stern of the boat to tie those to the car. That rides on the highway very easily with no shifting. With two people, the load/unload time is around 10 minutes as long as one person knows what they are doing. This kit had exactly what I was looking for, seems built to last, and if I ever need another kit to help tie a canoe to a car then I know I can trust this product to get the job done safely and reliably.

Bought a pair of these to go on 59" rhino rack bars on our Outback Wilderness and am really pleased. I left the bars full width - they are not a head banger on the car - and mounted the Hullavators as far outboard as possible which means the kayaks clear the side of the car and wing mirrors without folding them in. I did have to modify one Hullavator to make the Hobie Lynx fit (36" wide Lynx = 36" max Hullavator width)

Click to Enlarge

Click to Enlarge

2018 Ram 2500, wanted a way to travel with 2 sit on top kayaks, With my wife and i in our late 60's it was taking a LONG tome to get the kayaks on the roof of the bed cover. With these i can do it with a short stool. Also carrying the kayaks upside down keeps the top cleaner and stops the water from getting trapped in the kayak (and raining down on me when I unload them).

Click to Enlarge

Click to Enlarge

Click to Enlarge

Excellent product, easy install, secure on the crossbars, a bit lower ride height and a simple rolling mechanism. A significant improvement over my older Yakima Handroll racks.

The Sweet Roll will not support my Old Town Topwater 10.6. The brackets spread out on the crossbar under the weight. This year I will try a Yakima Big Catch. The Sweet Roll works fine with our Old Town Loons.

These work great! They fit well with my Brightlines Aero Rack where others did not. Super Good quality and super easy to install, I was surprised on the quality. I gave it 4 Stars because they sort of shift to the side if I put alot of pressure, however once the weight of the kayaks get on it, I don’t think it will be any problem.

Click to Enlarge

quick and easy installation. shipping was faster than quoted. pleasure doing business with.

I've used my locking Watersport Carrier numerous times over the past year to carry my two SUP boards. It's been wonderful! The fact that it synches down securly offers an additional level security on long trips, and it's very easy to load on/off. Would definitely recommend!

I can only comment on what my daughter has said, since it was a Christmas gift, and she lives out of state. It works perfectly and has been very durable.