# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
2nd order from etrailer, great customer service & fast delivery! My 2" ball fit the ball mount perfectly and I installed it in a few minutes. Make sure that you use a ball with a 1" shank. It stores easily underneath my Hyundai Santa Fe cargo mat until I need it.
My order arrived in two days. I am impressed both by the layout and functionality of etrailer website and by the quick, free shipment. The hitch for my 20007 Hyundai Santa Fe is well made, well finished and fit perfectly. The estimated installation time of 30 minutes would probably have been accurate had I not had to clean 3 years worth of rust from the mounting nuts installed by the factory. Once clean (no simple task since reaching them with a 10m/1.25 tap was difficult) mounting the tow bar was simple and made easier with a pair of jackstands. Owing to the design and location of the mounts, reaching them required the use of different ratchet extensions and flexible joints and I'm not certain of the accuracy of any torque reading. In summary, I am pleased with the product and impressed by the follow-up from etrailer. I will recommend them without hesitation.
# 2
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
Works as advertised. Great fit and now my boat is level traveling down the road. Fast turn-a-round. For [xx] shipping and the heavy weight, expected delivery in a week or two. Two days later it was at my doorstep, arriving late evening. Great service. Thank you.
was easy enough to install with the factory tow kit on my 17 Hyundai santa fe. Instruction pictures and installation video show ground (White) wire is connected to one of the electrical connectors. This was not the case as mine came with the white wire hanging loose, easy enough to install a ground connection to the frame as I did not know how to open the electrical connectors to attach the ground to the actual plug.
# 3
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 4
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
# 5
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
Works as advertised. Great fit and now my boat is level traveling down the road. Fast turn-a-round. For [xx] shipping and the heavy weight, expected delivery in a week or two. Two days later it was at my doorstep, arriving late evening. Great service. Thank you.
was easy enough to install with the factory tow kit on my 17 Hyundai santa fe. Instruction pictures and installation video show ground (White) wire is connected to one of the electrical connectors. This was not the case as mine came with the white wire hanging loose, easy enough to install a ground connection to the frame as I did not know how to open the electrical connectors to attach the ground to the actual plug.
# 6
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
This was the longest hitch ball mount I could find anywhere. I used it with a short extension for my 2021 T G so that I could open the back doors without hitting the trailer wheel crank. With my new trailer, Intact Flyer Discover, I don't need the extension and can still open the doors. Works well.
# 7
Brophy Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 13-1/4" Long - 10K
I’m pleased with the product and how prompt the delivery was. However the packaging was insufficient and the packaging was torn open all over. Scuffing of the finish is a result and of little consequence due to the intended use. It’s a stinger w/ball for motorhome. May I suggest better packaging in the future
Slightly longer, so you can open your tailgate with a cargo trailer attached. Trailers with a tongue jack that is forward are problematic for tailgates...
# 8
Draw-Tite Ball Mount - 3/4" Rise, 2" Drop - 10-1/2" Long - 6,000 lbs
2nd order from etrailer, great customer service & fast delivery! My 2" ball fit the ball mount perfectly and I installed it in a few minutes. Make sure that you use a ball with a 1" shank. It stores easily underneath my Hyundai Santa Fe cargo mat until I need it.
My order arrived in two days. I am impressed both by the layout and functionality of etrailer website and by the quick, free shipment. The hitch for my 20007 Hyundai Santa Fe is well made, well finished and fit perfectly. The estimated installation time of 30 minutes would probably have been accurate had I not had to clean 3 years worth of rust from the mounting nuts installed by the factory. Once clean (no simple task since reaching them with a 10m/1.25 tap was difficult) mounting the tow bar was simple and made easier with a pair of jackstands. Owing to the design and location of the mounts, reaching them required the use of different ratchet extensions and flexible joints and I'm not certain of the accuracy of any torque reading. In summary, I am pleased with the product and impressed by the follow-up from etrailer. I will recommend them without hesitation.
# 9
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Drawbar looks great and will be using in next two days. Thanks!
# 10
Brophy Ball Mount - 1" Rise, 2" Drop - 9-3/4" Long - Aluminum - 8,000 lbs
This stinger fits perfectly with my boat trailer and pickup. Having a bad back, the reduced weight is very helpful when removing and installing my Rock Tamer mud flaps. Shawnee was a huge help in determining what would work best for my application!!!
Very nice ball mount. Smooth, one piece design. Unlike my previous ball mount, it's long enough (enough straight length between the pin hole and the beginning of the bend) to accommodate a Blue Ox Hitch Receiver Immobilizer II, yielding a nice, tight connection. Attractive polished finish. Made in Taiwan (according to the box it came in). Photos show it attached to a Hidden Hitch Class III Hitch Receiver, secured with a Blue Ox Hitch Receiver Immobilizer II, and a Curt 40053 2-inch stainless steel ball.
# 11
Curt Dual Length Ball Mount for 2" Hitches - 2-3/8" Rise, 3-5/8" Drop - 7,500 lbs
Fits my Forester dealer-installed 2 inch receiver perfectly with the pin (purchased separately) in the first hole. The gas tank is in the way so I can't push it in further to the second hole. It is impressively strong, so there is no problem with it extending rearward a bit, but ideally I would get a shorter hitch if I could have a do-over, just for ease of storage.
Purchased to extend the trailer away from the back of the vehicle, and increase the drop. Initially could not fit in to my receiver, eventually figured out that the end of the 2" square was mushroomed, had to remove excess metal with a rotary tool. now it fits as far as the first 5/8" pin hole. No issues with use - seems sturdy, metal finish seems durable. Didn't drop the trailer tongue as much as I had hoped, but that's on me - I was probably running a 3" drop before, but I thought it was 2".
What our customers are saying:
"Product arrived very quickly. Everything was there and fit properly. I'm very satisfied."