# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
No complaints about this draw bar. Powder coat was nice and shiny. Holes were in the right place, and welds were solid.
Etrailer shipped my order the same day and the receiver is very well made and fit perfect.
# 2
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
GLORIOUS!!! Bought this item with zero experience, but much research. It is the best vehicle-related purchase I have ever made! Item performs exactly as advertised, even in spite of much abuse I have given it. Just because I could, I load tested it right at the edge of the max distributed towing weight, multiple times. No problems ever! Easy to install properly and safely!!! Well made construction! In my opinion, the best on the market at any price, but fortunately not the highest price by a pleasant margin!!!
I bought this hitch to fit my 2017 Ford edge. I'm impressed with the quality and sturdy construction. I will be using it to haul a U-Haul trailer. I would certainly recommend this insert to anyone looking for a fairly priced solution.
# 3
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
GLORIOUS!!! Bought this item with zero experience, but much research. It is the best vehicle-related purchase I have ever made! Item performs exactly as advertised, even in spite of much abuse I have given it. Just because I could, I load tested it right at the edge of the max distributed towing weight, multiple times. No problems ever! Easy to install properly and safely!!! Well made construction! In my opinion, the best on the market at any price, but fortunately not the highest price by a pleasant margin!!!
I bought this hitch to fit my 2017 Ford edge. I'm impressed with the quality and sturdy construction. I will be using it to haul a U-Haul trailer. I would certainly recommend this insert to anyone looking for a fairly priced solution.
# 4
Curt Dual Length Ball Mount for 2" Hitches - 2-3/8" Rise, 3-5/8" Drop - 7,500 lbs
Fits my Forester dealer-installed 2 inch receiver perfectly with the pin (purchased separately) in the first hole. The gas tank is in the way so I can't push it in further to the second hole. It is impressively strong, so there is no problem with it extending rearward a bit, but ideally I would get a shorter hitch if I could have a do-over, just for ease of storage.
Purchased to extend the trailer away from the back of the vehicle, and increase the drop. Initially could not fit in to my receiver, eventually figured out that the end of the 2" square was mushroomed, had to remove excess metal with a rotary tool. now it fits as far as the first 5/8" pin hole. No issues with use - seems sturdy, metal finish seems durable. Didn't drop the trailer tongue as much as I had hoped, but that's on me - I was probably running a 3" drop before, but I thought it was 2".
# 5
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I have traveled across the US towing an overloaded Uhaul 12' trailer. The trailer was still behind me when I arrived, so the hitch functioned as promised. I did not, however, require the extra long hitch as suggested for my particular vehicle, but it will serve as an extra. Unnecessary purchase. My son has since purchased a hitch from etrailer for his new Ford Edge. We're both happy - very robust and well engineered product(s)
Very usable for my purpose, just I wanted..
# 6
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 7
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
Purchased this hitch as a companion for our Reese anti sway control. The small ball for the Reese sway control fits in the bracket and the 2” drop on the hitch is exactly what we needed to have our Jayco camper level when towing.
# 8
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
This was the longest hitch ball mount I could find anywhere. I used it with a short extension for my 2021 T G so that I could open the back doors without hitting the trailer wheel crank. With my new trailer, Intact Flyer Discover, I don't need the extension and can still open the doors. Works well.
# 9
MaxxTow Ball Mount w/ 2" Accessory Receiver - 2" Hitches - 2-1/4" Drop - 5,000 lbs
Heavy duty , very good quality.
# 10
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
GLORIOUS!!! Bought this item with zero experience, but much research. It is the best vehicle-related purchase I have ever made! Item performs exactly as advertised, even in spite of much abuse I have given it. Just because I could, I load tested it right at the edge of the max distributed towing weight, multiple times. No problems ever! Easy to install properly and safely!!! Well made construction! In my opinion, the best on the market at any price, but fortunately not the highest price by a pleasant margin!!!
# 11
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I installed one of your Draw Tite trailer hitchs on my 2014 Ford Edge. However my carrier would not fold up without hitting my car. I just ordered a Draw Tite hitch for my wife's MKX and stumbled on this accessory which solved the problem. Hell to get old!
What our customers are saying:
"ordering was fast, easy and very quick turn around"