# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
GOOD QUALITY
# 2
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
this hitch is great. i needed a longer ball mount to give me more room between my trailer jack and spare tire on the tail gate of my jeep wrangler. it is very hard to find a extra long ball mount. i found etrailer has them and a lot of other fine products.
# 3
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
Purchased the 2" ball and mount kit along with the wiring kit for my 2015 Wrangler. Everything arrived on-time (as usual!!) and installation was exactly as depicted on the website videos. I highly recommend etrailer for your towing needs. Next will be setting the jeep up to be towed behind the motorhome and again I will order from etrailer!!!
Hitch fit real smooth, wiring harness went fast, Deliver was quicker than expected thank you
# 4
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
Hitch was as expected... appreciate the extra communication by etrailer.
Excellent product - very strong and secure! Does not, however, fit my 2016 Jeep Wrangler Unlimited. It is about 3.5 inches too short to clear the spare, and about that much too tall to go under the spare.
# 5
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 6
Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
Purchased the 2" ball and mount kit along with the wiring kit for my 2015 Wrangler. Everything arrived on-time (as usual!!) and installation was exactly as depicted on the website videos. I highly recommend etrailer for your towing needs. Next will be setting the jeep up to be towed behind the motorhome and again I will order from etrailer!!!
Hitch fit real smooth, wiring harness went fast, Deliver was quicker than expected thank you
# 7
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
The ball mount was a complete failure even after a lengthy discussion on the phone. I wanted a ball mount that would accept the rocker ball and anti-sway bar. The bar sent to me can't be used this way. An email and phone message to the sales person I ordered with, got no response.
What our customers are saying:
"You folks are fast. Thank you very much."