Most Popular 7500 lbs GTW for 2011 Ford Edge

Etrailer shipped my order the same day and the receiver is very well made and fit perfect.

Excellent

Etrailer shipped my order the same day and the receiver is very well made and fit perfect.

Excellent

GLORIOUS!!! Bought this item with zero experience, but much research. It is the best vehicle-related purchase I have ever made! Item performs exactly as advertised, even in spite of much abuse I have given it. Just because I could, I load tested it right at the edge of the max distributed towing weight, multiple times. No problems ever! Easy to install properly and safely!!! Well made construction! In my opinion, the best on the market at any price, but fortunately not the highest price by a pleasant margin!!!

I installed one of your Draw Tite trailer hitchs on my 2014 Ford Edge. However my carrier would not fold up without hitting my car. I just ordered a Draw Tite hitch for my wife's MKX and stumbled on this accessory which solved the problem. Hell to get old!

GLORIOUS!!! Bought this item with zero experience, but much research. It is the best vehicle-related purchase I have ever made! Item performs exactly as advertised, even in spite of much abuse I have given it. Just because I could, I load tested it right at the edge of the max distributed towing weight, multiple times. No problems ever! Easy to install properly and safely!!! Well made construction! In my opinion, the best on the market at any price, but fortunately not the highest price by a pleasant margin!!!

Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.

With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.

Click to Enlarge

Click to Enlarge

Purchased this hitch as a companion for our Reese anti sway control. The small ball for the Reese sway control fits in the bracket and the 2” drop on the hitch is exactly what we needed to have our Jayco camper level when towing.

Click to Enlarge

Click to Enlarge

Purchased to extend the trailer away from the back of the vehicle, and increase the drop. Initially could not fit in to my receiver, eventually figured out that the end of the 2" square was mushroomed, had to remove excess metal with a rotary tool. now it fits as far as the first 5/8" pin hole. No issues with use - seems sturdy, metal finish seems durable. Didn't drop the trailer tongue as much as I had hoped, but that's on me - I was probably running a 3" drop before, but I thought it was 2".

Each time we go camping we look for ways to improve the experience, the C45230 will allow us run with a short or long ball mount, the longer extension allows me to open my tail gate without disconnecting from the trailer. I looked at other manufacturers but was only able to find what I was looking from CURT, and etrailer offered the best price.

Click to Enlarge

Click to Enlarge