Most Popular Redline for 2003 Chevrolet Silverado

My manufactured trailer did not have this type with a grease fitting. They wore out the bushing in no time. I really like the design and ability to lubricate the bushing.

the web site has alot of good info that will answer any questions. I recieved my order in a week and shipping was free. all parts fit well except for the u bolts being too long. I cut them to fit my axles and springs.

Working great as I had expected. Always great to deal with etrailer

Nice and heavy duty.

Had a leaf spring break on my off-road trailer in Mexico. Left it at a boat yard until I received the parts from trailer & returned to replace. Only took 2 hrs to replace both leafsprinhs, shackles, bolts etc. And we were back on the road.

Excellent, had everything I needed and more for my trailer. Everything fit well!

Click to Enlarge

Click to Enlarge

This is a great kit! It included everything we needed to replace the old, worn-out brackets on our 6'x10' trailer. The directions were helpful and the brackets and hardware are nice and solid. We've had zero issues with the leaf springs (purchased on etrailer.com, also) or the brackets. Would definitely recommend!

great deal and fit to my order and fast shipping

These were purchased to assist with raising a dual-axle travel trailer. They arrived well packaged, and looked to be well made.They took readily to welding, so there was no issue with inferior material. The attached images show them being welded side-by-side to the frame rail extensions, then the entire assembly attached to the main frame.

Click to Enlarge

Click to Enlarge

Click to Enlarge

This is an excellent product, but I gave it four stars because it was nearly impossible to install with ordinary tools. It was necessary to force the serrated portion into the center hanger and since I did not have access to power to run a compressor and force it into the hole using excess torque via an air wrench, I had to use a hammer to drive the serrated end into the hanger. I found an install video from etrailer that showed how the installation was to be done, but I could not accomplish it that way. Besides the amount of torque needed would probably have twisted the bolt off at the grease hole. As it was, I drove the part in with a 3# hammer after destroying ordinary white wood blocks of wood. I removed the grease zerk and used another piece of flat iron to protect the zerk's threads. I was able to bottom the head against the hanger by tightening the nut as much as I could by hand and then hitting the head with the hammer a few times, tighten again, etc., until it was completely in place. This method was used on both sides of the trailer. To torque these into position with an ordinary wrench would have exceeded 1000 lbft of torque which I am not sure that these bolts would take without damaging them more than the hammering did. To be fair, the information suggested that the hangers be replaced, but that was because many times the hangers are damaged if the other parts wore out. But it is fairly clear that the holes in the hangers are not pre-formed with matching serrations so I doubt that it would have changed the issue. In short, I don't believe that the serrated portion is necessary. And if it is, then a keying method would be more appropriate, such as a square hole.

Other than cotter pin is way too small and had to add a couple washers so castle nut reached keeper hole a great product at a good price.

Good quality and heavy duty.

Had a leaf spring break on my off-road trailer in Mexico. Left it at a boat yard until I received the parts from trailer & returned to replace. Only took 2 hrs to replace both leafsprinhs, shackles, bolts etc. And we were back on the road.

I appreciate your informative response to my questions. The RV leaf spring is exactly what I needed. Thank you and I will continue doing business with you. Thanks to Dan for helping me place this order.

Exact duplicates of the stock Dexter equalizers. Removed nylon bushings and replaced with steel bushings with wet bolts.

Click to Enlarge

I purchased these u- bolts to go along with the new 3500lb axle I purchased from etrailer for a 12’ utility trailer. Once installed the trailer tolls better than even when new. I highly recommend etrailer for all trailer needs.

Disappointed that this could be sent out like this. The one package came with one ubolt and three nuts. In undamaged packaging.

Click to Enlarge

Worked for what I needed. No issues so far.

These are the lippert brackets, I bought for spares just in case I was to break one in travels. Alsome product.