Best 2002 Ford Windstar Trailer Hitch Ball Mounts

Works great, a little loose in the receiver just like any other hitch I have used.

Just Alright - made in CHINA I ordered this per etrailer's suggestion to use with a Curt Class III Receiver Hitch on a 1999 Ford Windstar to pull a pop-up camper. The ball mount (which is made in CHINA) is built very solidly , but there seemed to be a lot of play once inserted into the Curt receiver. There was a lot of clunking around back there while either accelerating, braking, or simply pulling. I ended up wrapping the ball mount shaft with a layer or two of duct tape to tighten things up a bit and alleviate some of the obnoxious clunking. The Ford Winstar pulls great. The Curt receiver is as good as they get (and made in the U.S.A.). The Drawtight ball mount seems to be the weak link in my setup. Next time I'd go with a CURT ball mount. Plus CURT is made in the U.S.A

The welding splatter found its way to the hitch pin hole and it took me some time with a Dremel to clean it out so the hitch pin would slide in.

Each edge of the hitch receiver shipping carton was pierced by mounting brackets, but no damage fortunately. Consider adding another layer of cardboard padding?

Works great.

Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.

I've got a lowered 1995 VW Jetta with a 1.25" receiver. I had to use a 6" extension along with a long, straight drawbar so any steep incline had me going at an angle and even then I would sometimes scrape. Some one had this drawbar on their Jetta and it looked good. With the measurements provided on this site I determined it would sit far enough away from my bumper and elevate the ball so my trailer wouldn't be angled down so much. Very glad I ordered this unit, it fits the car and works perfectly! Much better than my previous fix.

Great all around except for the fact that the retaining pin is a clip over, as opposed to a push through. That said, I simply safety wired the retaining clip and that took care of it. Very satisfied overall.

Every Item I have ordered from etrailer.com has been top of the line . Easy ordering , prompt service , and excellent installment instructions . I watch the video , more than once , and follow the expert's direction . I wouldnt order trailer parts anywhere else . Thank You

I believe my choice, with the help of etrailer, of this Draw-Tite trailer hitch receiver, along with a few other items to go with it, such as the drawbar, hitch ball and wiring harness, was a good one for my 2017 Subaru Forester. I also have to compliment etrailer for their excellent video on how to install it. All together, it really made the purchase very easy and smooth. Thanks etrailer.

The hitch and ball mount are excellent quality. My concerns are twofold. The hitch is so heavy that I had to take it to my mechanic to have it installed. Minor cost and inconvenience, but the hitch for my previous F-150 was just as sturdy, but easy to install myself (albeit with higher ground clearance). My concern about the ball mount is that the factory told me erroneously that it could not be reversed for a drop, so I returned it. This order is for the replacement after I was finally correctly told it could be reversed and how to do that. Ball mount would have been a 3 for that reason, and overall hitch and ball mount quality a 5. So I averaged them.

I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.

We sold our small motor home and purchased a small travel trailer. This hitch provided a perfect solution to how to use our bike rack while towing the trailer. It even allows room for the pickup tailgate to be lowered without removing the bikes from the rack. The hitch is very hefty with a high weight limit - plenty for the GVW of the trailer (7,000#) plus 125# of rack and bikes.

This has been an amazing multipurpose ball mount. We purchased this to use with our Hollywood Bike Rack and also to connect onto our boat. We weren't sure if this would work, but it was awesome. It is very well built and We had to make some minor adjustments to the position of our boat on the trailer so the turning radius of the bike rack that was attached would clear the truck. This is very well made and solid.

Everything arrived on time and well packaged. I installed a Curt hitch receiver to go with this ball mount. Installation for the hitch went exactly as described and was fairly simple for even a novice like me. Very pleased with etrailer.com and with Curt brand products in general. Couldn't be happier with the process from beginning to end. And the hitch looks and works great!

I would have given you guys 5 stars if it were not for the way the items were packaged. The ball mount and break controller were loose in a medium sized box with out any packing in between. The box for the break controller was smashed. I don't see any visual damage on the break controller its self but, I also haven't wired it in. It would be a good idea to separate these items with some kind of packing materiel so they don't slam around in the box. Other than that the products arrived as advertised.

Heavy duty , very good quality.

Excellent product! With the three different ball sizes, this tri-ball mount gives you a lot of flexibility. Gone are the days of having several different ball mounts to fit different tongues. High quality construction makes this an excellent investment.

This item should solve the problem I have had with a stainless 3-way ball when I tried to reverse the position on the ball mount. The threads galled between the hex nut and hitch ball.

Nice and heavy duty. Make sure you order the 1/2" pin when you order this.

We really like the hitch we ordered for our Camry. It was extremely easy to install. Fit perfectly!

My Mini Cooper is lowered and this unit really helped level out the trailer I am pulling. The product is heavy and solid. I would definitely recommend this item

Heavy duty! I was a little bummed when I found out how much more difficult it was to find a half inch pin for this, but no matter. It is a tad loose inside the hitch, so there's a little rattle, but I doubt it's as noticable as I make it seem. Super classy and a welcome change from the typical draw bar style. Goes great with my Volvo V70 T5. Thanks etrailer.com!

I used this on a 2014 Ford Fusion with a Reese receiver hitch made for my vehicle. Either the neck of the drop hitch is not long enough to get the ball a few inches away from the vehicle or the Reese receiver hitch sits too far under the vehicle.

Worked as advertised

Great purchase experience. eTrailer has this convenient package of ball and hitch already torqued together, AND includes a locking pin in addition to the normal cotter pin! Website is clear on details of package, contents, and dimensions of each component. Shipping was fast and packaged well. I’m not sure if I saved money compared to buying all this separately, but I’m going to believe I did. Thanks!

dodge journey 2014 etrailer service excellent the hitch don't fit perfect with the spare tire other ways is pretty good if you tele out the spare tire you going to have a hard time to put them back etrailer sevicio es excelente la pieza no se acopla perfecto con la rueda de repuesto del resto se monta perfecto . si se retira la rueda de repuesto es muy dificil de poner de vuelta en el compartimento

Just what I needed, most receivers would not allow me to open the tail gate on my 2022 dodge ram without hitting the trailers crank used to mount and dismount the car hauler trailer, this receiver give me the extra few inches I needed and it works perfectly, I tried many local sources but they all came up too short, etrailer is the place to go for all trailer parts, they seem to know and sell exactly what you may need

For a 7,500 lb hitch, I was surprised it didn’t have a wedge support welded on where the flat iron is welded to the square tube.