# 1
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Just Alright - made in CHINA I ordered this per etrailer's suggestion to use with a Curt Class III Receiver Hitch on a 1999 Ford Windstar to pull a pop-up camper. The ball mount (which is made in CHINA) is built very solidly , but there seemed to be a lot of play once inserted into the Curt receiver. There was a lot of clunking around back there while either accelerating, braking, or simply pulling. I ended up wrapping the ball mount shaft with a layer or two of duct tape to tighten things up a bit and alleviate some of the obnoxious clunking. The Ford Winstar pulls great. The Curt receiver is as good as they get (and made in the U.S.A.). The Drawtight ball mount seems to be the weak link in my setup. Next time I'd go with a CURT ball mount. Plus CURT is made in the U.S.A
Works great, a little loose in the receiver just like any other hitch I have used.
# 2
Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-3/4" Long - 3,500 lbs
Easy ordering, fair pricing, prompt delivery...product arrived in excellent condition, very heavy duty drawbar for use with by 4ft x 8ft medium duty trailer.
This drawbar was clearly used. See the picture. I asked etrailer about it and sent this picture but the person that replied, Noah, thought it must have been bumped around in shipping. If shipping caused this much damage, it's a poor quality product. If it was, in fact, used, then etrailer lied to me. Either way...not good.
# 3
etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit - 7,500 lbs
I purchased the etrailer.com 2-3/4 " Rise or 4" Drop Ball Mount Kit, Curt Trailer Hitch Receiver and Twist-in 7-Pole RV-Style Trailer Connector for my 2011 Chevy Silverado. Quick Delivery! All the necessary parts arrived in perfect condition. Directions were spot on and the instructional videos were great.
The drop ball mount is the perfect size for my Jeep. The versatile hitch balls are convenient. Thank you for putting together a great kit, providing excellent communication, and delivering it quickly.
# 4
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Works great.
Just Alright - made in CHINA I ordered this per etrailer's suggestion to use with a Curt Class III Receiver Hitch on a 1999 Ford Windstar to pull a pop-up camper. The ball mount (which is made in CHINA) is built very solidly , but there seemed to be a lot of play once inserted into the Curt receiver. There was a lot of clunking around back there while either accelerating, braking, or simply pulling. I ended up wrapping the ball mount shaft with a layer or two of duct tape to tighten things up a bit and alleviate some of the obnoxious clunking. The Ford Winstar pulls great. The Curt receiver is as good as they get (and made in the U.S.A.). The Drawtight ball mount seems to be the weak link in my setup. Next time I'd go with a CURT ball mount. Plus CURT is made in the U.S.A
# 5
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
I have a custom made tow guard. The ball mount I have was too short to allow me to attach the tow guard to my new truck. I searched the web and found just what I needed at etrailer.com. It's the only site I found that carried the size I needed. The product fits my needs perfectly. I can now protect my boat from rocks and other road debris when towing. Thank you etrailer.com.
# 6
Draw-Tite Drawbar for 1-1/4" Hitches - 5" Rise - 10" Long - 3,500 lbs
This is the correct towbar for a Toyota Prius C. The towbars that are available from U-haul (3 1/8") and other hardware stores are too low to the ground for most trailers. I tow my Harley Dyna on a motorcycle trailer behind my Prius C with no problem. Save yourself the grief. I bought three readibly available tow bars until I found the right one. The 5" rise, 10" long works perfectly. This is an incredibly strong drawbar.
Worked perfectly Did have to grind off the paint and a nit of metal to fit in the reciever though.
# 7
Draw Tite Drawbar for 1-1/4" Hitch - 5/8" Rise, 1-1/4" Drop - 9-3/4" Long - 3.5K
Works perfectly for me. I use it to tow a motorcycle trailer behind my Mini Cooper with a concealed hitch so I need the extra length to clear the bumper. No complaints.
Excellent quality, solid steel bar and wields are excellent. The black coating is heavy and well applied. I’m Very happy with this product!
# 8
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.
Easy install, took around 30 minutes by my self to install. Hardest part of install was torquing the bolts ! Installed 13322 Class III Hitch - Gm 1500/2500 Pickup and Curt Class III Ballmount -2ball-2 Drop
# 9
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
# 10
etrailer Ball Mount Kit - Extra-Long - 2-3/4" Rise or 4" Drop - 6,000 lbs
Excellent Web site, easy to navigate, great prices, easy purchase experience, fast delivery. I had someone install the hitch - all good, looks great - no photo, but take my word - it looks great on my 2003 Buick Rendezvous. An easy, "Five Star" rating (Web sales experience and hitch).
The products ordered from eTrailer shipped and arrived quickly. Nothing was damaged and I was able to install everything easily. The extra long draw bar is perfect for my 2012 Town & Country mini van, providing good clearance of the rear bumper and ground. I would highly recommend these products.
# 11
Curt Class III Ball Mount with 2-5/16" Ball - 2" Drop - 7,500 lbs
Everything arrived on time and well packaged. I installed a Curt hitch receiver to go with this ball mount. Installation for the hitch went exactly as described and was fairly simple for even a novice like me. Very pleased with etrailer.com and with Curt brand products in general. Couldn't be happier with the process from beginning to end. And the hitch looks and works great!
etrailer is great! My hitch shipped quickly and was packaged well. Plus customer service has been great keeping me updated and staying in touch with my order.
# 12
MaxxTow Ball Mount w/ 2" Accessory Receiver - 2" Hitches - 2-1/4" Drop - 5,000 lbs
Heavy duty , very good quality.
# 13
Curt Tri-Ball Mount - 3 Chrome Balls - 10,000 lbs
definitely solid as a rock
Excellent product! With the three different ball sizes, this tri-ball mount gives you a lot of flexibility. Gone are the days of having several different ball mounts to fit different tongues. High quality construction makes this an excellent investment.
# 14
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Drawbar looks great and will be using in next two days. Thanks!
# 15
Curt Class II Euro Style Drawbar with 2" Ball - 2-5/8" Rise - 3,500 lbs
It isbthe right size and helps with the height difference to make the trailer more even with the back end of my Accord.
Look and quality of the mount is awesome. Beefy in size as well. If using on my particular application, removal of rear diffuser is necessary. If they had extended it another inch it woulda been perfect. 2015 Audi a3 tdi. Wouldn’t let me add a third pic but it’s a finger tip space between the ball and bumper with diffuser removed.
# 16
Curt Drawbar for 1-1/4" Hitches - 5-3/8" Rise, 6" Drop - 5-9/16" Long - 2K
I used this on a 2014 Ford Fusion with a Reese receiver hitch made for my vehicle. Either the neck of the drop hitch is not long enough to get the ball a few inches away from the vehicle or the Reese receiver hitch sits too far under the vehicle.
Website was easy to use and order. Tracking the package was simple to follow and package arrived on schedule. Part works great
# 17
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 2" Rise, 4" Drop - 7.5K
Nice combination to go with my front hitch for the F150.
dodge journey 2014 etrailer service excellent the hitch don't fit perfect with the spare tire other ways is pretty good if you tele out the spare tire you going to have a hard time to put them back etrailer sevicio es excelente la pieza no se acopla perfecto con la rueda de repuesto del resto se monta perfecto . si se retira la rueda de repuesto es muy dificil de poner de vuelta en el compartimento
# 18
Draw-Tite Ball Mount - 6-3/4" Rise, 8" Drop - 10" Long - 5,000 lbs
Just Alright - made in CHINA I ordered this per etrailer's suggestion to use with a Curt Class III Receiver Hitch on a 1999 Ford Windstar to pull a pop-up camper. The ball mount (which is made in CHINA) is built very solidly , but there seemed to be a lot of play once inserted into the Curt receiver. There was a lot of clunking around back there while either accelerating, braking, or simply pulling. I ended up wrapping the ball mount shaft with a layer or two of duct tape to tighten things up a bit and alleviate some of the obnoxious clunking. The Ford Winstar pulls great. The Curt receiver is as good as they get (and made in the U.S.A.). The Drawtight ball mount seems to be the weak link in my setup. Next time I'd go with a CURT ball mount. Plus CURT is made in the U.S.A
Works great, a little loose in the receiver just like any other hitch I have used.
# 19
Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
My order was missing installation parts, but the etrailer team were quick to correct the issue. Even without a lift, I was able to install the receiver and brake light cable quickly, thanks to their extensive video libray.
I cannot emphasize enough how kind and thorough etrailer's customer experience team is. I originally (incorrectly) place an order for trailer parts that did not fit together, and etrailer took the time to review my order, identify the issue, call and email me to let me know, and place the correct order while over the phone. I am not an expert on any of these items so it is so unbelievably appreciated that they cared enough to check to see if I meant to order what I did. The delivery then arrive a day earlier than expected. What more could you possibly want from a customer service team? Thank you so much, etrailer!
# 20
Curt Class III Drawbar - 2" Rise - 4" Drop - 13" Long - 7,500 lbs
Haven't used it yet. I bought it because of CURT's quality. It was beat up in shipping though.
Exactly what I needed to extend the reach of the ball beyond my rear tire carrier WITHOUT losing any tongue weight capacity! I used mine for the 2" rise.
What our customers are saying:
"In these days of customer "no service" I am usually disapointed when doing business with people I don't know. It was refreshing doing business with you. I'm impressed!"