# 1
Wet Equalizer Bolt with Locknut and Grease Zerk for Double-Eye Springs - 3" Long
I bought a set of these bolts to replace the hardware in the triple axle suspension of my toyhauler. I had read about the benefits of a wet bolt kit, and after finding two broken shackle plates on my camper, decided I too needed to be able to properly lubricate the moving parts. These were a perfect fit and replacement for my original bolts. At the time I installed them I hadn't read about orienting the hole in the bolt to the 3 or 9 o'clock to ease pumping grease through them. I put them in at whatever orientation they were in my hand, but had no problem pushing 3 - 4 pumps of chassis grease through the zerk. I was able to observe grease flow out of the spring eyes around every bolt, and all of the zerk fittings stayed firmly in place when I wrestled the grease gun nozzle on and off. There were a few bad reviews about these press on fittings falling out, but I didn't see any evidence of that. I am very pleased with this purchase, and enjoy the peace of mind that comes with knowing I can properly service my suspension and hopefully extend the life of all the components in the system.
My manufactured trailer did not have this type with a grease fitting. They wore out the bushing in no time. I really like the design and ability to lubricate the bushing.
# 2
U-Bolt Kit for Mounting 5,200-lb to 7,000-lb, Round Trailer Axles - 7-1/16" Long U-Bolts
Ordered a lot of parts for a dump trailer rebuild in Sept. Didn't install some of the final parts until Christmas break. THEY SENT COARSE THREAD NUTS INSTEAD OF FINE. I ruined 2 u-bolts and need all 16 fine thread nuts. I'm outside 60 days so I was told I'm on my own. I've spent $5k+ on etrailer. I'll find some place else.......
Exact replacement for original parts, easy install
# 3
Single-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front, 7/8" Rear
The parts are of an excellent quality, Web site service was great, I could find everything I needed and all of the support to complete the replacement job. Delivery was exceptionally fast for my orders.
This is a great kit! It included everything we needed to replace the old, worn-out brackets on our 6'x10' trailer. The directions were helpful and the brackets and hardware are nice and solid. We've had zero issues with the leaf springs (purchased on etrailer.com, also) or the brackets. Would definitely recommend!
# 4
Replacement U-Bolt for 2" Wide, Square Axles - 7/16" Diameter - Zinc Plated
Exactly what I needed...delivery was spot on...thank you!
Seem like a good quality bolt, will see how they hold up.
# 5
Tandem-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4" Front/Rear, 5-7/16" Center
I spoke with Trevor, Thursday the 11th, I have 1set, 2 PCs, of shackle straps that are shorter than the other 6 shackle straps. I have been waiting for An email from Trevor, have not received it. Could I get the correct straps sent 2 PCs needed. Thanx
I have ordered from Etrailer a few times now, The service is always great and fast shipping. They have the best prices around. Where I live I have 24 miles of rough dirt road so am always replacing parts on my trailers. Their products hold up to the test of my road. Always a perfect fit too!
# 6
Replacement U-Bolt with Nuts for 2-3/8" Round Trailer Axles - 1/2" Diameter - Zinc Plated
We used the U-Bolts on a device built to allow multiple antennas on a single pole. I attached a couple of images, one after construction and one on a rooftop installation.
I tell all my friends to order from etrailer.com. great products from the u bolts to rims and tires. I have replaced all the rims and tires on my tandem axle boat trailer, you can not beat the price or the service. Pat C. is always spot on in guiding you to the right parts. shipping fast and on time. Thanks Pat C. and etrailer Barry
# 7
Replacement U-Bolt with Nuts for 1-3/4" Wide, Square Trailer Axles - 9/16" Diameter
Worked and fit perfect. Thanks
Quick delivery and excellent customer service (with follow-up emails to ensure that everything was ok with the order). This replaced a broken bolt on a 1956 camper trailer, and it's a very close match to the original.
# 8
2" Square Trailer U-Bolt (Qty 2)
Had a leaf spring break on my off-road trailer in Mexico. Left it at a boat yard until I received the parts from trailer & returned to replace. Only took 2 hrs to replace both leafsprinhs, shackles, bolts etc. And we were back on the road.
Great Experience! When I noticed that the leaf springs on my 44 year old boat trailer had cracked I thought I would never find replacements. I fully expected to have to have something custom built. I was amazed when I found the fantastic diagrams/descriptions dimensions for replacement springs on etrailer.com The phone support person was wonderfully helpful in confirming if items were in stock and ready to ship. The replacement springs arrived on time and everything bolted up perfectly! Thanks for such a great site!
# 9
Wet Equalizer Bolt with Castle Nut, Grease Zerk and Cotter Pin - 3-1/2" Long
This is an excellent product, but I gave it four stars because it was nearly impossible to install with ordinary tools. It was necessary to force the serrated portion into the center hanger and since I did not have access to power to run a compressor and force it into the hole using excess torque via an air wrench, I had to use a hammer to drive the serrated end into the hanger. I found an install video from etrailer that showed how the installation was to be done, but I could not accomplish it that way. Besides the amount of torque needed would probably have twisted the bolt off at the grease hole. As it was, I drove the part in with a 3# hammer after destroying ordinary white wood blocks of wood. I removed the grease zerk and used another piece of flat iron to protect the zerk's threads. I was able to bottom the head against the hanger by tightening the nut as much as I could by hand and then hitting the head with the hammer a few times, tighten again, etc., until it was completely in place. This method was used on both sides of the trailer. To torque these into position with an ordinary wrench would have exceeded 1000 lbft of torque which I am not sure that these bolts would take without damaging them more than the hammering did. To be fair, the information suggested that the hangers be replaced, but that was because many times the hangers are damaged if the other parts wore out. But it is fairly clear that the holes in the hangers are not pre-formed with matching serrations so I doubt that it would have changed the issue. In short, I don't believe that the serrated portion is necessary. And if it is, then a keying method would be more appropriate, such as a square hole.
Other than cotter pin is way too small and had to add a couple washers so castle nut reached keeper hole a great product at a good price.
# 10
Rear Hanger for 2" Wide Slipper Springs - 5-1/4" Tall - 5/16" Bolt Hole
Works like their supposed too. I've built several trailers and all were built with etrailer parts, good quality, good service and great prices.
The exact part I needed
# 11
U-Bolt Plate for 2-3/8" Round Axle - 1-3/4" Wide Springs - 1/2" Bolts - Galvanized
1 Year in and still working flawlessly. Put around 2500 miles on the boat trailer since they have been installed.
Easy install. Holding up well in salt water.
# 12
Front/Center/Rear Hanger for Double-Eye Springs - 4-1/4" Tall - 9/16" Bolt Hole
These were purchased to assist with raising a dual-axle travel trailer. They arrived well packaged, and looked to be well made.They took readily to welding, so there was no issue with inferior material. The attached images show them being welded side-by-side to the frame rail extensions, then the entire assembly attached to the main frame.
My order was supposed to arrive on Saturday by Monday evening I had not received it I called the lady was very apologetic and said she would research it. She took care of everything and it was here. They were very helpful .!! the part was exactly what I needed Would definitely recommend them for their personnel and their follow up
# 13
Replacement U-Bolt for 2" Wide, Square Axles - 1/2" Diameter - Zinc Plated
I ordered the ubolt kit for 2” square axle when i bought my new leaf springs. My old ubolts were 5 1/2”, the new ubolts were only 4 1/2”. Not long enough to use lock washer and thread bolt sufficiently. I had to order longer ubolts to make it work, only to find out 2 things. 1- the new longer ubolts do not include washers or nuts. 2- the 4 1/2” ubolts were fine thread while the new 5 1/4” are coarse thread, so i had to make the 6 mile trip to home depot to buy new coarse thread nuts. Why do you suggest a ubolt kit that doesn’t work with a 2” square axle and a 4 layer leaf spring
Product was adequate for my needs. Expected delivery was Thursday. ???? 2 1 1/2 mile trips on foot to the mailbox 2 days later and it arrived late today. Won’t be ordering items from you again. Your choice of transportation is horrible. UPS item will be delivered as scheduled. Saved a buck on the first shipment. Lost a customer! Pass this on to the idiot that decided to save a buck. Good bye!
What our customers are saying:
"very easy to shop"