Filter Questions and Answers:

reset filter

Expert Answers about RV and Camper Hitch


  • What Are the Specs for the Lippert 2 Inch Trailer Hitch Receiver LC730647
  • The Lippert 2" Trailer Hitch Receiver part # LC730647 is specific to Vanleigh 5th Wheel Trailers. If you take a look at the attached photo you will see that there are tabs on this trailer that sit below the frame and the trailer hitch attaches to these. These two tabs are spaced 72" apart so if this is what you have then the Lippert 2" Trailer Hitch Receiver will work but I don't have any sort of spec sheet on this as it is a custom fit trailer hitch. If you don't have a Vanleigh 5th...
    view full answer...

  • Bolt-On Trailer Hitch for a 2018 Vanleigh Vilano 5th Wheel Trailer
  • I spoke with Lippert about the Trailer Hitch Receiver for Vanleigh 5th Wheel Trailers part # LC730647 and they said this would work on your 2018 Vanleigh Vilano if the distance between your two frame rails inside to inside is 72". If this distance is not 72" then there would not be a bolt-on trailer hitch available which means your only option would be a universal fit trailer hitch. If that is the case I recommend the Adjustable Width Trailer Hitch Receiver for RVs part # 13703 because...
    view full answer...

  • Best Rear Hitch Options 2016 Montana High Country 362RD 5th Wheel
  • You could go with the Lippert 2" Trailer Hitch Receiver for Campers and Trailers # LC730647 you were looking at, but because this only hitch has a 300-lb tongue weight rating I believe there is a better solution. I recommend going with the Curt Adjustable Width Trailer Receiver # 13703 , because it has a slightly higher 350-lb tongue weight capacity. You'll want to measure the frame width on your Keystone Montana High Country 362RD to make sure that it isn't wider than 72", but as long...
    view full answer...

  • Trailer Hitch Recommendation for Fifth Wheel Trailer Frame that is 71 inches Apart
  • The best multi-fit hitch option we offer for your fifth wheel trailer frame that is 71 inches apart that will have the hitch opening the closest to the rear of the trailer is the Curt part # 13703. This fits frame rails that are up to 72 inches apart outside to outside and the hitch tube sticks out 8-3/16 inches forward of the crosstube of the hitch. See picture.
    view full answer...

  • Recommended Trailer Hitch Receiver For 5th Wheel Trailer Frame
  • For your 69 inch frame measurement you can use the Curt Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide # 13703 or # C13704 both of which have a tongue weight rating of 350 lbs but with different mounting styles. These both are bolt on options. There is also a weld on option in the Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames # UF35-946403. My recommendation is the Curt # C13704 based on the ease of installation with the bolt-on method from the bottom...
    view full answer...

  • Difference Between Curt Adjustable Trailer Hitches 13703 and 13704
  • The difference between the Curt Adjustable Width Trailer Hitch Receivers # 13703 and # C13704 are a couple things, starting with the # C13704 having a 5,000 lb towing capacity and 500 lb tongue weight capacity while the # 13703 has a a 3,500 lb towing capacity and 350 lb tongue weight capacity. Both fit box frames, C-channel frames, or I-beam frames, though the # C13704 is for frames 22" to 68-1/2" wide while the # 13703 is for 22" to 72" wide frames. The Stabilizing Straps # 18050...
    view full answer...

  • Where on Trailer Frame to Measure for Adjustable Width Trailer Hitch for RVs
  • Thanks for all those measurements! There is a trailer hitch that will work great for your travel trailer, though the measurement you want to go with is from outside to outside, which you said was 70-1/2 inches. That means the correct hitch is the Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide # 13703. This is a Class III hitch with a 2" receiver and 350 lb tongue weight capacity so you will be able to carry a good deal of cargo with it. For a cargo carrier on the rear...
    view full answer...

  • Bracket Measurements of Trailer Hitch Receiver for RVs
  • I have added a cut out for you which shows the measurements of the brackets on the Adjustable Width Trailer Hitch Receiver for RVs # 13703 as well as how they mount to box frames, C-channel frames, or I-beam frames. This 2 inch receiver will work on trailer frames that have a width between 22 inches and 72 inches wide and has a 3,500 lb capacity with a 350 lb tongue weight capacity, though I recommend contacting the trailer manufacturer to find out exactly what the capacity of your trailer...
    view full answer...

  • Front Mounted Trailer Hitch Receiver for 1985 Dodge Van
  • There aren't any front-mounted trailer hitch receivers that are custom designed to fit for a 1985 Dodge B350 and your bumper is not structurally strong enough to work with the Curt RV Bumper 2" Trailer Hitch Receiver # E-100. What that means is the only option that might work is a universal, adjustable-fit hitch such as the Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" wide # 13703 or the Multi-Fit Motorhome Trailer Hitch, 24" - 46" wide # 5350 or 47" - 71" wide # 82201. These...
    view full answer...

  • Recommended Trailer Hitch for 2007 Keystone Montana 3400rl 5th Wheel Trailer
  • The Draw-Tite Multi-Fit Motor Home Trailer Hitch, 47" - 71" wide # 82201 has a maximum tongue weight of 300 lbs. If you have a frame that is shorter then the Draw-Tite # 5350 is a great option with a 500 lb tongue weight. If you are unsure of the width of your trailer frame the Curt Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide # 13703 is a great option that with either bolt or weld on and is rated for 350 lbs tongue weight. If you have a frame between 18-51 inches...
    view full answer...

  • Carrying Bikes at the Front of a Travel Trailer
  • You could use the Swagman Straddler # S80503 if you want to. However you have to stay within the capacity of the Straddler which is 100 pounds. That means the combined weight of the bike rack you use and the bikes cannot exceed 100 pounds. The Swagman Dispatch # S64684 weighs about 51 pounds by itself meaning the combined weight of the bikes cannot exceed 49 pounds. You could instead go with Swagman rack # S64663 which weighs about 30 pounds. You would not use the hitch part that comes...
    view full answer...

  • Correct Adjustable Width Trailer Hitch for I-Beam Frame That is 69 Inches Wide
  • The Adjustable Width Trailer Hitch Receiver for RVs, 22" to 68-1/2" Wide # C13704 is for frames that are a maximum of 68-1/2" wide so it is not the correct hitch for your 69" wide I-beam frame. For a frame of that width you would need the Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide # 13703 though it has different brackets, and I've added a photo of their dimensions for you to take a look at. These brackets can be flipped (on both hitches) without issue. If that...
    view full answer...

  • Recommendation For A Hitch For A 2017 Heartland Cyclone 5th Wheel Toy Hauler
  • We have both frame-mount and bumper-mount hitches for your 2017 Heartland Cyclone 5th Wheel Toy Hauler and I have attached a link to our available inventory. Generally, Frame-mount hitches like the Curt Adjustable Trailer Hitch Receiver, Item # C13701, offer higher capacity than the bumper-mount variety like the Curt RV Bumper Hitch, # C19101. The Curt Adjustable Trailer Hitch Receiver has a Class III rating and can be bolted or welded on. It works with frames with a minimum width...
    view full answer...

  • Bike Rack Recommendation for Carrying 60 lb Bike at Rear of Travel Trailer
  • I do have a bike rack solution that will work well for your, but not every bike rack is designed for the rouger ride quality at the rear of a camper. I wish I could recommend the Thule EasyFold XT part # TH903202 for you as it is a great rack, but it shouldn't be used at the back of a travel trailer. The most similar option is the Swagman Escapee part # S64693 which has a 60 lb per bike capacity and can be used at the rear of a camper so it would work well for you. This would work great...
    view full answer...

  • What is the Difference Between Curt Trailer Hitches # C13701 and # C13702
  • These are actually the exact same trailer hitch with the only difference being that the # C13701 has a 2" drop while the # C13702 doesn't. Both are Class III hitches with a 2" receiver that is rated for 5,000 lbs GTW (gross trailer weight) and 500 lbs TW (tongue weight). They fit frame widths from 18" - 51" and have a 1/4" bracket thickness. These Curt trailer hitches are made in the USA and come with a limited lifetime warranty. Review videos and installation instructions have been...
    view full answer...

  • Recommended Trailer Hitch for a 2019 Forest River Rockwood Ultra Lite with Welded Bumper
  • Thanks for the photo! I can now see the issues you are having trying to install a trailer hitch on your 2019 Forest River Rockwood Ultra Lite Fifth Wheel. That said, the brackets for the Adjustable Width Trailer Hitch Receiver part # 13703 and the Adjustable Width Trailer Hitch Receiver part # C13704 are too large to attach to the square tubing used to attach your bumper and this square tubing would get in the way if you tired to mount the hitch to the frame underneath. Therefore the...
    view full answer...

  • Is RV Trailer Hitch Available with 10,000 lb Weight Capacity
  • If you are looking for a trailer hitch to mount on your RV then the highest rated capacity is the Curt Trailer Hitches parts # C13702 and # C13701 which are both rated for a max of 6,000 lbs towing when a weight distribution (WD) system is used. These are the same hitch with the only difference being the 13701 has a 2" drop for the receiver. We do have the Ultra Frame Service Body Trailer Hitch Cross Tube # 41991 which has a 16,000 lb towing rating but I'm not sure if it would fit your...
    view full answer...

  • Trailer Hitch for 2019 Forest River Cardinal With I-Beam Frame
  • The Lippert 1-1/4" Trailer Hitch Receiver for I-Beam Campers and Trailers # LC240220 you referenced gets ordered as customers order it so there isn't a specific date I can offer. However, to answer your question, if Forest River said this is a fit then that is not something I would be able to discount. Having said that, this hitch is designed to fit trailer frames with 68-3/8" between the I-beams. There is definitely another option, the Adjustable Width Trailer Hitch Receiver for RVs,...
    view full answer...

  • Trailer Hitch for Camper Frame With Bolt Holes 51 Inches Apart
  • The Adjustable Width Trailer Hitch Receiver # C13701 is 51 inches from end to end (see accompanying photo), so to fit your camper you will want to go to the next size up, the Adjustable Width Trailer Hitch Receiver for RVs, 22" to 68-1/2" Wide # C13704. This hitch has a longer crosstube but it is designed to be trimmed so the ends are flush with the brackets. This is a Class III hitch with a 2" receiver and has a lifetime warranty which speaks to its durability. Please keep in mind...
    view full answer...

  • Will the Stromberg Carlson Bike Bunk Part # CC-275 Fit a 2018 Lance Model 1995
  • The Stromberg Carlson Bike Bunk part # CC-275 will fit trailers that have space on the a-frame between 14"-55" back from the center of the coupler. As long as the weight of the rack and two bikes does not exceed 100 lbs then you will have no problem using the bike bunk with two bikes on your trailer. Also, please keep in mind that the bike rack must be rated for use on an RV in order to abide by the carriers warranty. If you do not have space available on the tongue of your a-frame...
    view full answer...

  • Weight of 2 inch Curt RV Bumper Trailer Hitch Receiver and Securing It With Bike Rack
  • I checked with the manufacturer for you and the Curt RV Bumper 2" Trailer Hitch Receiver # E-100 weighs 12 lbs. This hitch fits 4" x 4" square bumpers and while there is technically not a built-in security measure to keep someone from taking the hitch, it does get torqued down tightly to your bumper as you can see in the linked instructions, so it would be quite a bit of work to take it. Additionally, if you were using a bike rack such as the Thule Range 4 Bike RV Rack # TH9057 or...
    view full answer...

  • Is It Possible to Install Trailer Hitch on 2006 K-Z Escalade Trailer
  • It is absolutely possible to install a trailer hitch on your 2006 K-Z Escalade trailer; it will only require that your trailer have a box frame, C-channel frame, or I-beam frame that is between 22 inches and 72 inches wide. Should your trailer have that you will be able to use the Adjustable Width Trailer Hitch Receiver for RVs # 13703 which will can either bolt or weld onto your trailer's frame. This is a Class III hitch with a 2 inch receiver but please keep in mind it will require...
    view full answer...

  • How to Carry Heavy E-Bikes on Back of Trailer
  • While there is a way to carry your heavy e-bikes on the rear of a trailer, there is no way to safely carry e-bikes on the front of your trailer because there isn't a method that can handle the 100 lb - 110 lb capacity you need. So what you'll require is a trailer hitch for your trailer and an RV-approved bike rack. For a trailer hitch, I recommend the Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide # 13703. This will work on trailers with a box frame, C-channel frame,...
    view full answer...

  • Trailer Hitch Recommendation for Trailer with 72 inch Wide I-Beam Frame
  • For a multi-fit hitch that fits a 72 inch wide I-beam trailer frame like what you have you'd want the Curt Multi Fit hitch part # 13703.
    view full answer...

  • What is Purpose of Rear Hitch Installed on 5th Wheel Trailer
  • Trailer makers typically install hitch receivers on their 5th wheel and travel trailers to enable owners to use items like an RV-approved bike rack, such as the Swagman E-Spec 2-Electric Bike Platform Rack # S64689. Not all hitch accessories can be used on trailers or motorhomes but this particular Swagman carrier can be used on ANY vehicle, car, truck, van, pop-up camper, 5th wheel or motorhome. This sturdy rack is unique in this respect. Using a bike rack in the trailer's hitch will...
    view full answer...

  • Bike Rack Needed to Fit Over Propane Tanks on a 20' 2016 Venture Sonic
  • We have a few options for you to carry your bikes over the tongue of your 20' 2016 Venture Sonic. The first option would be to use the Stromberg Carlson Bike Bunk # CC-275 which will fit frame widths from 12" to 52" and will allow you to attach a bike rack to the 2" receiver. One of the most popular bike racks that is used with this is the BikeWing-2 # B01311. It weighs 17 lbs and can carry up to 80 lbs of bike! (40 lbs each) If you are running out of room on your frame we also have...
    view full answer...

  • How To Triple Tow with a 5th Wheel Trailer
  • The Curt Adjustable Trailer Hitch Receiver part # C13701 will need to be mounted to the frame rails on your 2017 Keystone Cougar 5th Wheel Trailer, not the bumper. The bumper is not a suitable place to mount this hitch but the frame rails are. If you would like to use a bumper mounted trailer hitch and you have a 4" x 4" bumper that the manufacturer says can be used for towing then you can use the Curt RV Bumper 2" Trailer Hitch Receiver part # E-100 instead. However, the manufacturer is...
    view full answer...

  • Trailer Hitch for RV With Frame Width of 75 Inches for Cargo Carrier
  • There is a trailer hitch that will fit your 75 inch wide frame but you should not use spacers to install the Adjustable Width Trailer Hitch # 13703 due to potential instability on a frame longer than its intended use. Instead the best option is the Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames # UF35-946403 which is adjustable and welds onto I-beam, C-channel or rectangular trailer frames that are between 47-1/8" and 77" wide so it is perfect for your 75 inch frame, though it...
    view full answer...

  • Recommended Trailer Hitch for 2011 Keystone Passport 245RB
  • As long as your 2011 Keystone Passport 245RB has a box frame, C-channel frame, or I-beam frame that the frame members are no more than 66" apart, you can use the Curt Adjustable Width Trailer Hitch Receiver for RVs # C13704. This hitch can be bolted on to the frame with the included hardware and will provide you with a 2" receiver that will allow you to tow a trailer with. To install a wiring harness to power the trailer lights on your Keystone Passport you can use the Curt Vehicle...
    view full answer...

  • How Much Can the Rear Bumper Hold On A Vintage RV Camper
  • I would not be able to speculate on the rear bumper capacity for any one particular trailer especially one this old but if you feel you will be exceeding this with the Curt RV Bumper 2" Trailer Hitch Receiver part # E-100 you can add supports, the Mount-n-Lock SafetyStruts Universal RV Bumper Support Brackets part # MO34VR. The other options would be a frame mount trailer hitch, the Adjustable Width Trailer Hitch Receiver part # 13703.
    view full answer...

  • E-Bike Rack Recommendation for Two 70-lb E-Bikes at Back of 5th Wheel Trailer
  • For a e-bike rack that is rated for the weights of your e-bikes and also for the rougher ride quality found at the rear of a 5th wheel trailer we have the Hollywood Rack RV Rider part # HR1600 as the best option. This has an 80 lb per bike capacity which would easily handle your 70 lb bikes. The rack weighs 60 lbs so with the combined weight of your bikes it would weigh right at 200 lbs which would be most likely not too much for your RV hitch but you'd want to verify this by checking...
    view full answer...

  • Recommended Trailer Hitch for 2019 Coachman Freedom Express Ultra Lite 248RBS
  • On the Ultra Lite trailers like your 2019 Coachman Freedom Express Ultra Lite 248RBS, the manufacturers don't reinforce the bumpers to be able to handle that weight so the torque on the bumper is too great. The best solution is to use the Curt Adjustable Width Trailer Hitch Receiver for RVs, 22" to 68-1/2" Wide # C13704 or up to 72 inch wide # 13703. This trailer hitch will mount to the frame of your trailer and will allow you to use a bike rack or cargo carrier on your trailer. If...
    view full answer...

  • Trailer Hitch Receiver for 2018 Forest River Heritage Glen Trailer
  • The Curt Adjustable Trailer Hitch Receiver - 18"-51" Wide - 2" Drop # C13701 or the Curt receiver # C13702 are both great options for your 2018 Heritage Glen 282RK. These are rated for tongue weights of up to 500 lbs. I did a little research on your Yamaha 3500 generator dimension and based on what I found, I recommend using a cargo carrier like the TorkLift Lock and Load 27-3/4" x 24" Maximum Security Cargo Tray - 2" Hitches # TLA7752 or a more basic cargo carrier like # C18153. For...
    view full answer...

  • Bumper Mounted Trailer Hitch for RV That Mounts Underneath Bumper
  • The only solution really is a new trailer hitch receiver because the Swagman RV Bumper 2" Trailer Hitch Receiver # S64025 is a clamp-on designed only to be mounted above the the bumper and doing otherwise compromises the safety and integrity of both the hitch and your RV. There are bumper mounted hitch receivers that will accommodate 2 inch bike racks, which is what the Swagman was designed to do. The Buyers Products RV Universal Receiver Hitch # 3371804060 has a 2" receiver and as you...
    view full answer...

  • Recommended Flat Tow System for 2018 Chevy Silverado 1500 Crew Cab 4x4
  • Your 2018 Chevy Silverado 1500 crew cab 4x4 curb weight is 5,300 lbs based on my research. To flat tow this vehicle, I recommend upgrading your 5,000 lb hitch to the Curt Class V Universal Weld-on Receiver Hitch # 15903 which is a universal fit for frames between 18 and 61 inches wide. Then for your flat towing setup, I recommend you begin with the Roadmaster MX Base Plate Kit - Removable Arms # RM-3176-3 and use Loctite Threadlocker # LT37420 for the installation. Then for your...
    view full answer...

  • Will the Curt RV Bumper 2" Trailer Hitch Receiver E-100 Work To Pull a Trailer
  • The Curt RV Bumper 2" Trailer Hitch Receiver part # E-100 which is a fit for a standard 4" x 4" rear bumpers will allow you to tow a trailer up to 3,500 lbs. However, that is what the hitch is rated for and the bumper could be rated for less (must confirm with manufacturer). If so, you could install supports, the Mount-n-Lock SafetyStruts Standard RV Bumper Support Brackets part # MO22FR or installs a frame mount hitch, the Adjustable Width Trailer Hitch Receiver for RVs part # 13703.
    view full answer...

  • Trailer Hitch for 2005 Thomas Saf-T-Liner HDX Rear Engine Bus for Use with Hitch Motorcycle Carrier
  • We do have multi-fit RV hitches like the Curt # C13701 that you referenced but none of these has the req
    view full answer...

  • 4-Bike Rack for Use on Rear of Travel Trailer
  • It is fairly unusual for a travel trailer to have a 1-1/4-inch hitch installed; these days most trailers and RVs have a 2-inch hitch that offers more strength and a higher weight-carrying capacity. We offer 2-inch hitches made to install on RVs and trailers, both bumper-mount and frame-mount types, that are shown on the linked page. The highest weight capacity comes from a frame-mount type hitch like Curt's # 13703. This one can be bolted on or welded on to a trailer frame from 22-...
    view full answer...

  • Can a Bike Rack be Installed on the Trailer Side of the Bike Bunk # CC-275 for Clearance
  • Your idea for the Stromberg Carlson Bike Bunk # CC-275 is a great one, the only problem is that even some of our smallest bike racks stick out past the 16-1/2" of clearance that you are looking for. I may have another solution for you though. Check out the Lippert Jack-It # LC429756 that can hold up to 2 bikes weighing 40 lbs each. This bike rack installs on an A-frame trailer and fits around jacks with up to 2-1/4" outer tube diameter and 22-1/2" clearance. Since this bike rack holds...
    view full answer...

  • Solution for Carrying Bike rack While Towing Lance 1575 Travel Trailer
  • What I would recommend is to use the bike rack bunk part # CC-275 which attaches to the A-frame of the trailer to give you a hitch opening above the frame so that a bike rack like the BikeWing part # B01311 can be carried. I attached a review video for this adapter for you to check out as well.
    view full answer...

  • How To Carry an Electric Bike on the Back of a Trailer
  • I do have an option for you but the heaviest bike you can carry on the back of a trailer is 70 lbs due to the availability of hitch bike racks that can be used on a trailer. If you can get your e-bike down to 70 lbs then you can use the Swagman E-Spec 2-Electric Bike Platform Rack part # S64689. However, I strongly recommend that you reach out to the trailer manufacturer to see how much you can carry on the bumper with a bumper mounted trailer hitch like the Curt RV Bumper Trailer Hitch...
    view full answer...

  • Replacement Hitch for RV on 2019 Ford E-350 Chassis
  • If the frame on your RV on a 2019 Ford E350 chassis is between 47" and 71" wide, you can use the Multi-Fit Motor Home Trailer Hitch # 82201 to replace the existing hitch. This is an adjustable hitch designed to sit between the frame members on your chassis and will provide you with a 2" hitch receiver. This hitch can be bolted on to both existing or drilled holes in the frame or welded on, for a no drill application. I've also linked our other available selections that might work in...
    view full answer...

  • Recommended Trailer Hitch Receiver for 5th Wheel Trailer to Carry Bike Rack
  • The trailer hitch receiver I recommend for your 5th wheel is the Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide # 13703. There are no specific fits for your toy hauler, but this fits a huge range of RVs; you only need to ensure your 2007 Tahoe Transport 3450 has a box frame, C-channel frame, or I-beam frame that measures between 22" and 72" wide from inside to inside. I have added a link to the instructions as well as a video review for you to check out of the Adjustable...
    view full answer...

  • How Many Bikes Can be Used on the Stromberg Carlson Bike Bunk CC-275
  • The Stromberg Carlson Bike Bunk Trailer-Mounted Bike Rack Carrier part # CC-275 will allow for you to carry as many bikes as you please so long as the weight of them plus that of the carrier does not exceed 100 lbs. There is no limit to the number of bikes that can be used. However, the bike carrier must be rated for use on a trailer so that is something to keep in mind as well. For a lightweight bike carrier that can be used on a trailer, I recommend the Swagman Original part # S64152-2...
    view full answer...

  • Recommended Trailer Hitch Receiver for 2008 KZ Spree 27 RLSE 5th Wheel Trailer
  • For your 2008 KZ Spree 27 RLSE 5th wheel trailer, the Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames # UF35-946403 is a great weld on option that will give you a 3,500 lb towing capacity and a 350 lb tongue weight. For a bolt-on option, I recommend the Curt Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide # C13704 which is rated for trailers up to 3,500 lbs and 350 lb tongue weight. You can alternatively use the Curt # 13703 which uses a different style bracket...
    view full answer...

  • Heavy Duty Adjustable Receiver Hitch for my 2020 Vanleigh Vilano Camper
  • We have exactly what you need! The Adjustable Width Trailer Hitch Receiver for RVs part # C13704 gives you the 500 lb. weight rating you are looking for and gives you an adjustable range of 22" to 66" Wide RV Frame widths. This will include all of the hardware you will need to do the installation. Check out the link and video on it below. Happy Camping!
    view full answer...

  • Recommended Bike Rack for 2013 Big Horn 5th Wheel
  • There are a number of bike racks that have been rated for use on the back of 5th wheels and motor homes. I recommend going with the Thule Range 4 Bike RV Rack # TH9057 which works on 2" hitches. With the Thule Range, you get a high quality product that comes along with the Thule brand at a great price. This hitch will allow you to safely carry 4 bikes on the back of your 2013 Big Horn 5th wheel. This hitch mounted rack comes with the HideAway anti-sway cradles with ratcheting straps...
    view full answer...

  • Recommended Trailer Hitch Receiver for 2017 Winnebago Winnie Drop 170S
  • For your 2017 Winnebago Winnie Drop 170S travel trailer, I recommend using the Curt Adjustable Width Trailer Hitch Receiver for RVs, 22" to 68-1/2" Wide # C13704. This will give you the ability to bolt the receiver to your Winnebago travel trailer frame and then you can use a cargo carrier like # H01472 for your large cooler. I've linked the page to all our Cargo Carrier options to assist.
    view full answer...

  • Bracket and Hitch Tube Dimensions of Ultra-Fab Trailer Hitch # UF35-946403
  • On Ultra-Fab trailer hitch # UF35-946403 the brackets that make contact with the frame are 4 inches by 3 inches. The hitch opening sticks out 5-1/4 inches from the main tube of the hitch as well.
    view full answer...

  • Recommended RV Trailer Hitch Receiver for Trailer Frame Over 51 Inches Side to Side
  • For your trailer with a 69.5 inch framed to frame measurement I recommend the Curt Adjustable Width Trailer Hitch Receiver for RVs # 13703. This RV trailer hitch is adjustable from 22 inches up to 72 inches wide, so it will work well for your trailer frame dimensions. This is a bolt-on or weld-on application with a 3,500 lb capacity. We have a more economical option that is only weld-on in the Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames # UF35-946403 which will fit frames...
    view full answer...

  • Recommended RV Bumper Hitch to Transport Firewood
  • It sounds like you are referring to the RV Bumper 2 Inch Trailer Hitch Receiver # S64025. This particular bumper hitch is designed to be used with hitch-mounted bike racks and is not recommended for use with a cargo carrier, as the weight that they will provide is simply too much for the unit to handle. A better option for your application will be with the Curt RV Bumper Trailer Hitch Receiver # E-100. This is intended for 4 inch square channel bumpers and can be used with hitch-mounted...
    view full answer...

  • Does Trailer Hitch Receiver for Vanleigh 5th Wheel Come With Mounting Hardware
  • The Lippert 2" Trailer Hitch Receiver # LC730647 does come with mounting hardware so you can install it, as you can see by the cut out of the instructions I added. Just keep in mind this is designed to fit Vanleigh 5th wheel trailers that have a pre-existing bracket. I have added a second photo from the instruction manual so you can verify it has this bracket. If it does you will be able to easily install the Lippert 2" Trailer Hitch Receiver # LC730647.
    view full answer...

  • Can Brackets on Curt Adjustable Width Trailer Hitch Receiver Mount to Top of I-Beam
  • The Curt Adjustable Width Trailer Hitch Receiver # C13704 that you referenced should be mounted to the bottom of the I-beam frame on your trailer. This is how the hitch was tested and rated by the manufacturer so altering the brackets so that they sit on top of the frame could result in an unknown, lesser weight capacity. I have attached the written installation instructions that you can check out as well.
    view full answer...

  • Recommended Trailer Hitch for 2018 Fuzion 373 Toy Hauler
  • To install a trailer hitch on the back of your 2018 Fuzion 373 Trailer I recommend the Curt Frame Mount # 13703. This particular unit is designed specifically for trailers like yours and its adjustable brackets allow it to fit frame widths of 22 to 72 inches. It can either be bolted directly to the frame using the included hardware or welded on for a no-drill application. The hitch features a 3,500 pound towing capacity and a 350 pound tongue weight limit. I have attached a sample install...
    view full answer...

  • Comparing the Stromberg Carlson # BA-100 and Swagman # S64025 Bumper Mount Receivers
  • The only real difference, aside from the manufacturer, between the Stromberg Carlson # BA-100 and the Swagman # S64025 receivers is that the Stromberg Carlson fits 4-1/2" x 4" bumpers while the Swagman fits 4" x 4" bumpers. I have linked some review videos for you to check out as well.
    view full answer...

  • Trailer Hitch and Bike Rack for Motorhome to Carry 70 lb Electric Bike
  • While there is a way for you to carry a 70 lb electric bike on the back of a motorhome, there are no ladder-mounted bike racks that have the capacity to carry a 70 lb bike. Instead you will need to add a trailer hitch, the Multi-Fit Motorhome Trailer Hitch # 5350, which you can do so long as your motorhome has a chassis from 24" to 46" wide, or the Multi-Fit Motor Home Trailer Hitch # 82201 for frame widths from 47" to 71" wide. Once you have the right hitch you will simply need...
    view full answer...

  • Recommended Trailer Hitch for a 2020 Forest River Salem Cruise Lite Travel Trailer
  • Since your 2020 Forest River Salem Cruise Lite Travel Trailer has a rear bumper you'll need to install a bumper mount hitch receiver instead of one that installs directly to the frame. This is simply because anything installed to the frame will sit too far under your trailer for you to utilize the receiver. For your application I recommend the Curt RV Bumper 2" Trailer Hitch Receiver # E-100 which fits around a 4" x 4" square bumper and easily installs using the the included bolts and...
    view full answer...

  • Can the U-Bolts On the Ultra-Fab Motor Home Trailer Hitch Receiver Be Turned
  • The Ultra-Fab 2" Motor Home Trailer Hitch Receiver part # UF35-946401 has a bolt hole spacing of 5" front to back and 4" side to side so it does not sound like it would work for you. However, we do have the Stromberg Carlson 2" Motor Home Hitch Receiver part # BA-100 which has a bolt hole spacing of 5" front to back and 5" side to side so it does sound like it would work for you although I am not quite sure of the intended purpose.
    view full answer...

  • Mounting Bracket Dimensions of Curt RV Hitch 13704
  • The Adjustable Width Trailer Hitch Receiver for RVs, 22" to 66" Wide # C13704 has brackets that are 10 inches long with mounting holes 8-1/2 inches center on center. The height is right at 5-1/2 inches tall. I've attached a video to assist. The top of the receiver tube will sit about 2 inches from the bottom of your frame but the hitch ball height will be determined by your ball mount. I've attached an article to assist.
    view full answer...

  • Trailer Hitch that Could Possibly Fit 2011 Forest River Cherokee 235B Plus 4-Way Connector
  • As long as the width of the frame on your 2011 Forest River Cherokee 235B is between 22 and 68-1/2 inches (measured from outsides) the Adjustable Width Trailer Hitch Receiver for RVs # C13704 will fit and work well for you as it has a 5,000 lb trailer weight and 500 lb tongue weight capacity. To add a 4-way what you would need is the part # 18252. This is a 72 inch long 4-way connector that comes with quick-disconnects so that it can easily be attached to a trailer's taillight circuits....
    view full answer...

  • Hitch Tube Length of Draw Tite Hitch # 82201
  • The hitch opening of the Draw Tite hitch part # 82201 that you referenced measures 6 inches from the main cross tube.
    view full answer...

  • Bike Rack Solution for 2018 Airstream Basecamp Travel Trailer
  • Your photo suggests that the space available on your Airstream Basecamp trailer's frame to install the Stromberg Carlson Bike Bunk # CC-275 is just not large enough for a good fit. The Bike Bunk's brackets are almost 5-inches wide and it appears you'd have to do some serious cutting on your propane cover. On such a nice new premium travel trailer like the Basecamp I can see why this might make it more desirable to find another bike carrying solution. You might take a look at the Jack-It...
    view full answer...

  • Trailer Hitch that Can Fit RV for Carrying Bike Rack
  • We have multi-fit hitches that will work great on your RV like the Curt # 13703 but the two hitches you mentioned are not going to work great without a large amount of modification potentially as they were made for passenger vehicles. I attached an install video for the # 13703 for you to check out on a similar trailer as well.
    view full answer...

  • Mounting Adjustable Width Trailer Hitch on Puma Ultra Lite Camper
  • I'm attaching the installation video for the Adjustable Width Hitch # 13703 to this answer, but as you can see at about 5:00 into the video, the side plates of the hitch are going to sit directly on the ledges of your I or C beams of the frame of the trailer. For that reason, you're not going to be able to mount it lower than those plates are going to sit. I don't know if the black water tank will come into play as much as I would worry about the stabilizer jacks being the part that keeps...
    view full answer...

  • Recommended Trailer Hitch for for Trailer That Can Carry 500 Lbs
  • It sounds like you are wanting to install a trailer hitch on a trailer and if that is the case I have a few options. The first option which is the easiest to install is a bolt-on bumper hitch which only works if you have a square 4" x 4" rear bumper, the Curt RV Bumper 2" Trailer Hitch Receiver part # E-100. If you don't have a square 4" x 4" rear bumper then your only other option is a frame mount trailer hitch, the Curt Adjustable Trailer Hitch Receiver part # C13701. Please note,...
    view full answer...

  • Trailer Hitch That Fits 2015 Winnebago Trend
  • We have a trailer hitch that does fit your 2015 Winnebago Trend based on the dimensions you listed but since your frame is 55 inches from outside to outside the part # C13702 won't fit as it's max width is 51 inches. Instead you'd want the Curt # 13703 which fits up to a 72 inch wide frame width. This hitch also has a capacity of 3,500 lbs which would be more than enough for your application.
    view full answer...

  • Bolt Hole Spacing of the Multi-Fit Motor Home Trailer Hitch Part # 82201
  • The bolt holes on the Multi-Fit Motor Home Trailer Hitch part # 82201 are spaced 8-1/2" apart front to back. The bolt holes spaced left to right can be adjusted as needed up to 68". I have attached a photo with these measurements for you as well.
    view full answer...

  • Trailer Hitch for a 2015 Mercedes-Benz Sprinter Passenger Model
  • I do have an option for you but there is not an aftermarket custom fit trailer hitch available for a 2015 Mercedes-Benz Sprinter Passenger Model. If you need to install a trailer hitch then your only option for this is a universal fit trailer hitch for which I recommend the Adjustable Width Trailer Hitch Receiver part # C13704. The Adjustable Width Trailer Hitch Receiver is super easy to install as it only required two bolts per side in order to retain the 5,000 lb weight capacity. There...
    view full answer...

  • Recommended Travel Trailer Hitch Receiver and Cargo Carrier for Gas Generator
  • On your Dutchmen Coleman Lantern 17rd travel trailer, I recommend the Curt RV Bumper 2" Trailer Hitch Receiver # E-100 which has a weight capacity of 350 lbs maximum tongue weight. Then for a 4,000 watt running generator like the Q-iPower # 289-AP5000 which weighs 117 lbs and has dimensions of 23-1/4" long x 17" wide x 18-1/2" tall, you will want a cargo carrier like the TorkLift Lock and Load # TLA7752. This will not only help carry the generator but also deter theft. If you want...
    view full answer...

  • Recommended 2 Inch Trailer Hitch for 5th Wheel Trailer To Use With Bike Rack
  • The trailer hitch that I recommend for a fifth wheel trailer is the Adjustable Width Trailer Hitch Receiver for RVs part # C13704 which is hands down one of the most popular options for trailers due to its extremely universal design. The Adjustable Width Trailer Hitch Receiver has a 500 lb tongue weight capacity which should be enough for your bike rack and six bikes. The Adjustable Width Trailer Hitch Receiver for RVs bolts to the bottom of the trailer frame or possibly the bottom of the...
    view full answer...

  • Recommended Bolt-On Trailer Hitch for Trailer with I-Beam Frame
  • If you are looking for a bolt-on trailer hitch to install on a trailer then the Adjustable Width Trailer Hitch Receiver for RVs part # 13703 is your best option because it fits all different types of trailers such as those with an i-beam frame and it can be bolted on as you mentioned. The bolt holes would obviously not be present so what you would need to do is remove the side plates from the hitch and then use those on the side of the trailer frame as a template for drilling. The cross...
    view full answer...

  • Availability of Dimensional Drawing of Draw Tite Hitch 82201
  • I attached a picture I received from Draw Tite that shows the dimensions of Draw Tite hitch part # 82201 that you are looking for.
    view full answer...

  • Installation Of Ultra-Fab 2 Inch Trailer Hitch Receiver For 5th Wheel Trailer Frames
  • The manufacturer made the Ultra-Fab 2" Trailer Hitch Receiver for 5th Wheel Trailer Frames # UF35-946403 for a weld on application. It is possible to attach the hitch in the manner you suggested, but it is not rated for a bolt on application. Since this hitch isn't for towing purposes, it may function fine with a bolt on application but the drilling will bring down it's capacity. I've attached a picture of the dimensions for you. There isn't a ton of space for 4 holes and drilling will...
    view full answer...

  • Reciever Hitch for my 2020 Somerset E3 Deck Pop Up Camper.
  • The Curt Adjustable Width Trailer Hitch Receiver for part # 13703 is rated for 350 lbs. of toungue weight and 3500 lbs. of gross trailer weight. In your situation you would be well below the stated maximums and using the bolts to install the hitch to your frame would be perfectly acceptable. Of course please check with your camper's manufacturer to ensure that your camper is rated for towing once you have found that you do not want to exceed the lowest weight rating of the camper,...
    view full answer...

  • How to Mount a Bike Rack on a Cherokee Arctic Wolf 5th Wheel
  • The Ultra-Fab 2" Motor Home Trailer Hitch Receiver part # UF35-946402 will fit RV's with a 4" wide x 4" tall steel bumper and bike racks with a 2" receiver tube. However, in order to use a bike rack on the rear of an RV the bike rack must be RV approved. I do have an RV approved bike rack option for you but the Thule T2 Classic 2 Bike Platform Rack part # TH9044 is not. For a similar wheel mount 2 bike carrier that fits 2" hitches and is rated for use on the back of an RV, I recommend...
    view full answer...

  • Installation Instructions For Stromberg Carlson Bike Bunk Trailer-Mounted for A-Frame Trailers
  • I have attached a copy of the page from the installation instructions for the Stromberg Carlson Bike Bunk Trailer-Mounted for A-Frame Trailers, part # CC-275. I have also attached a link to a product review video for this carrier you can check out. The installation instructions are available on the product page for the CC-275 on our website.
    view full answer...

  • Hitch Recommendation for 2013 Heartland Cyclone 4100 for Bike Rack
  • For your 2013 Heartland Cyclone 4100 fifth wheel the best hitch option we are going to have is a multi-fit hitch like the part # 13703 that fits frame width between 22 and 72 inches apart. For a fifth wheel approved bike rack we have the Lets Go Aero part # B01311 which will allow you to carry up to 2 bikes at a time. I attached a review video for this and an install video for the hitch for you to check out as well.
    view full answer...

  • Trailer Hitch Option that Can Fit Back of Camper with More than 360 lb Tongue Weight Capacity
  • If your camper has a frame width between 22 and 66 inches the Curt # C13704 would potentially work as it can bolt on and has a 500 lb tongue weight capacity.
    view full answer...

  • Hitch Recommendation for 2003 Newmar Kountry Star Class A Motorhome
  • We offer both frame-mount and bumper-mount trailer hitches for use on the rear of a motorhome like your 2003 Newmar Kountry Star Class A. The bumper-mount hitch you referenced, Swagman # S64025, is intended for bumpers that are continuously-welded across their entire length. This hitch can be used only with an RV-approved bike rack. It cannot be used for towing or with cargo carriers. The link provided will let you see all available bumper- and frame-mount RV hitches. For a frame that...
    view full answer...

  • Recommended Motorhome Hitch With 69 Inch Wide Frame
  • We do offer a couple of hitches that will bolt to your motorhome frame that may work well for you. The price of the items we offer are listed on the product page below the product part number. You mentioned that the frame measures 69 inches center-to-center so I recommend the Curt Adjustable Width Class lll Trailer Hitch Receiver, part # 13703. This hitch will fit RV frames that measure 22 to 72 inches wide and the heavy-duty brackets can be welded or bolted on for installation. The...
    view full answer...

  • Can Two E-Bikes Be Used On the Rear Bumper for a Rockwood Mini Lite
  • If you will be carrying heavy e-bikes on your 2019 Rockwood Mini Lite 2304KS then I highly recommend a frame mounted trailer hitch, the Adjustable Width Trailer Hitch Receiver part # 13703 in particular. The rear bumper on your Rockwood Mini Lite can be used to carry other lighter items such as a spare tire but I would not use this for heavy e-bikes. That said, you would need to reach out to Rockwood in order to determine its weight carrying capacity. If it is rated for the weight of your...
    view full answer...

  • Recommended Trailer Hitch Receiver for a 2015 Keystone Montana Fifth Wheel Trailer
  • For your 2015 Keystone Montana Fifth Wheel, I highly recommend the Curt Adjustable Trailer Hitch Receiver part # C13701. This is one of the most universal trailer hitches we offer with a Class III rating and 2" receiver tube opening. As long as the width of your frame from the outside of each rails does not exceed 51" then this hitch will work great for you. It can either be welded or bolted into place though we do recommend a professional welder should you choose that option. I have...
    view full answer...

  • Bumper Mount Trailer Hitch for a 2005 Coachmen Spirit of America RV
  • Thanks for sending a picture! The typical weight rating of a 4-inch square bumper is no more than 200 pounds, but I highly recommend you contact your local Coachmen RV dealer or view your owners manual to find out the maximum weight rating because sometimes the manufacturer say no to any weight. It seems as if you spare tire is mounted to the bumper too, so that could eat into the weight capacity. If you determine your RV 4-inch bumper has the weight capacity you need and plan on...
    view full answer...

  • Bracket Measurements of Curt Adjustable Width Trailer Hitch Receiver
  • To answer your first question yes, you can swap the brackets end for end on the Adjustable Width Trailer Hitch Receiver for RVs # C13704. In regards to the measurements, I used your very handy graph to fill in the measurements you were looking for. A: 1", B: 2", and C: 3-1/2". This is a Class III hitch with a 2" receiver and capacities of 5,000 lbs towing and 500 lbs tongue weight; it will fit I-beam frames, box frames or C-channel frames that measure 22" to 68-1/2" wide. I have...
    view full answer...

  • RV Trailer Hitch Receiver Compatibility with Slide Out Bumper on 2014 Keystone Cougar 5th Wheel
  • The Curt Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide # 13703 is a very well made hitch. I haven't seen a hitch installed on a frame where there is a slider at the rear bumper, but that should not impact the strength or function of the trailer hitch when mounted to the frame chassis. This hitch should work well for your 2014 Keystone Cougar 5th wheel, you will just need to remember to remove your accessory from the hitch if it would make contact with the bumper slide...
    view full answer...

  • Availability of Trailer Hitch for Keyston Fuzion 390 to Tow 4-Wheeler Trailer
  • We have a number of different hitch options that may work for your Keystone Fuzion 390. Trailer hitches made for RV's are not vehicle specific so you may need to take a couple of measurements to be sure a hitch will work well on your trailer. One of the most universal fit trailer hitches for an RV is the Curt Adjustable Width Trailer Hitch Receiver # 13703. This hitch is adjustable to fit RV frame widths from 22 inches to 72 inches wide. Installing the hitch can either be a weld-on...
    view full answer...

  • Front-Mounted Universal RV Hitch for Using Motorcycle Carrier on 2007 Jayco Seneca Class C RV
  • We offer no custom front-mount hitches for the Chevrolet Kodiak frame on which your Jayco Seneca is built, but we do offer universal-fit RV hitches that are shown on the linked page. These are available in bolt-on and weld-on types, and with varying tongue weight (TW) capacities that range from 350-lbs to 500-lbs. The weight-carrying capacity of your Kodiak chassis must also be confirmed in order to know your actual capacity for hitch-mounted accessories like motorcycle carriers. The lowest-rated...
    view full answer...

  • Weight Capacities of Curt Trailer Hitch # C13704
  • The Curt Adjustable Width Trailer Hitch Receiver # C13704 referenced in your question features a 5,000 pound towing weight capacity and a 500 pound tongue weight limit. I verified this with Curt. This adjustable hitch is designed for use on trailer or RVs and will work on frame widths of 22 to 68-1/2 inches. I have attached a short video review that you can check out as well.
    view full answer...

  • Compatibility of Trailer Hitch Receiver on Rear of 5th Wheel Trailer
  • If the manufacturer states not to put a hitch on the back, then they may have determined it is not safe to anything behind it. We defer to the manufacturer as adding a hitch could void your warranty on the 5th wheel as well and we don't do any independent testing. If they do not explicitly state not to add a hitch, then most 5th wheel trailers do have the ability to use a hitch receiver like the Curt Adjustable Width Trailer Hitch Receiver for RVs # 13703 which is made for this type...
    view full answer...

  • Recommended Trailer Hitch for 1992 Toyota Hiace Motorhome
  • There isn't a custom, bolt-on trailer hitch available for your 1992 Toyota Hiace Motorhome so your best option will be with an adjustable unit like the Curt Class III # 13703. As long as the chassis features a box, C-channel, or I-beam frame and its width is between 22 and 72 inches this hitch will work great. It can be bolted on with the included hardware (which would require drilling) or welded on for a no-drill application. I have attached a sample installation video that you can...
    view full answer...

  • Would Curt Multi-Fit Hitch 13703 Fit 2015 Keystone Cougar
  • Most likely yes, but we do not have specific trailer fit info for the Curt hitch part # 13703 as it is a multi-fit hitch designed to fit as many RVs as possible. What you will need to do is measures the distance between the frame rails from outside to outside. If that distance is between 22 and 72 inches this hitch will fit and work well.
    view full answer...

  • Possible Trailer Hitch Fit for 2018 Sandpiper 372lok
  • The best option we have would be the multi fit hitch part # 13703 as it can fit trailer frames that are between 22 and 72 inches apart measured from outside to outside. It also will work on box frame, C-channel frame, or I-beam frames so it's very universal.
    view full answer...

  • Recommended A-Frame Cargo Adapter And Bike Carrier
  • The # CC-275 is designed to fit an A-frame trailer frame and will work on frames that are 14 to 55 inches wide. This carrier measures 33-1/2 inches from the top of the trailer frame to the top of the cross tube. I recommend using a hanging bike carrier like the Swagman Original, part # S64152-2. This bike carrier has a weight capacity of 35-lbs per bike. I have attached a photo of this bike rack being used with the # CC-275 on a trailer behind a pickup truck. As you can see, the bike...
    view full answer...

  • Mounting Plate Dimensions of RV Trailer Hitch
  • The mounting plate for the Lippert 1-1/4" Trailer Hitch Receiver # LC240220 is 8 inches wide and 3-1/2 inches tall. It has mounting holes which are 2 inches apart on center vertically and 6 inches apart on center horizontally. I have added a link to a video review for you to check out as well.
    view full answer...

  • Recommended Trailer Hitch for Lance 2185 Trailer
  • The frame-mounted Curt Adjustable Width Trailer Hitch Receiver # 13703 is your best option for adding a trailer hitch to your Lance 2185 trailer. This model is designed specifically for trailers like this and it can fit frame widths of 22 to 72 inches. It features a tongue weight capacity of 350 pounds, giving you a healthy safety margin for your small trailer. The hitch can either be bolted to the frame or welded on for a no-drill application. I have attached a sample install video...
    view full answer...

  • How Much Does the Lippert 2" Trailer Hitch Receiver Weigh?
  • The Lippert 2" Trailer Hitch Receiver # LC730647 weighs approximately 45-lbs and can be installed by bolting it on to the frame of your travel trailer or RV to allow you to carry hitch mounted accessories rated for use on the back of an RV or travel trailer. This hitch has a heavy-duty powder coated finish to help protect against rust and corrosion.
    view full answer...

  • Possible Trailer Hitch Fit for Keystone Fuzion Toy Hauler
  • The best option we have for a hitch for your Keystone Fuzion is going to be the Curt part # 13703 as it can fit trailer frames that are between 22 and 72 inches wide and can fit your frame style as well. The bolt hole of your trailer though aren't going to match up to this hitch. I attached an install video for this hitch for you to check out as well.
    view full answer...

  • Can Curt RV Bumper 2-Inch Trailer Hitch Receiver # E-100 Tow a 14-Foot Aluminum Boat
  • The Curt specialty hitch you referenced, # E-100, will fit a 4-inch square RV bumper and offers a maximum tongue weight capacity of 350-lbs and a maximum gross trailer weight capacity of 3500-lbs. If your boat and trailer's tongue and gross weights are within these limits then the hitch will be up to the task. The other thing you need to check is the Rustler's manual to see if it indicates any restrictions for the bumper itself for use with a bolt-on hitch. The bumper itself as well as...
    view full answer...

  • Recommended Trailer Hitch for Motorhome with Ford E450 Chassis
  • I do have a solution for you, however we do not currently have a custom-fit trailer hitch that is confirmed to work with the Ford E450 chassis on your motorhome. I recommend looking at the Adjustable Width Trailer Hitch Receiver # 13703. This is an adjustable hitch that can fit vehicle frames between 22 and 72 inches wide. The hitch can be bolted to the frame or welded on for a no-drill application. I recommend having any welding done by a certified professional. This will provide a...
    view full answer...

  • Dimensions of Mounting Brackets on Curt 13703 and 13704 Trailer Hitches
  • I attached two picture for the Curt hitch part # C13704 that have all of the dimensions on it. I believe you also asked for the distance from the crosstube to the front of the mounting bracket. Which if so, that distance is 2 inches. The third picture is the dimensions of the # 13703.
    view full answer...