I reached out to Lippert to confirm that you can change out your 24-1/2" rear jacks that come with the 4-Point Lippert Ground Control 3.0 # LC358590 with the Short Left Rear Leg # LC342610 and Short Right Rear Leg # LC428493. They confirmed that there will not be any issues with the control board and the shorter jacks. These jacks are 2" shorter at only 22-1/2" tall and still have the same 12-1/2" of total lift as your current jacks. view full answer...
I called Lippert and they informed me of the grease seal dimensions for your 3,500 lb axle. The correct replacement grease seal for you is part # 168255TB. view full answer...
The only thing I consistently pulled up with part number PBD 877-646-9233 was plastic pop-up vents. Here are the available options for your for a 2006 Forest River grey Wolf TT Toy Hauler :
Replacement Exterior Pop-Up Roof Vent-Black Steel Item # 9106
Replacement Exterior Pop-Up Roof Vent - Aluminum Item # RV-626-062
Redline 2-Way Pop-Up Roof Vent with Garnish Item # 9106-2756
Redline 2-Way Pop-Up Roof Vent with Garnish Item # RV-626-062-2756
Both are 13-1/2" x 8" and do not have to be... view full answer...
The R-Pod 189 usually comes fitted with four corner-mounted scissor jacks that bolt to the frame. We have a number of such bolt-on stabilizer jacks that are shown on the linked page.
Many of these are sold as pairs but we also have single jacks too, such as the item you referenced, part # TJSC-24, which offers up to 18-inches of extension. This 2500-lb-rated item has plenty of weight capacity for stabilizing one corner of your 189 so as long as the extension matches your other jacks this... view full answer...
I'd be happy to help out!
The Replacement Entry Door Hinge for RV - 6 Leaf - White # LC198295 you were looking at for your 2019 Forest River Sandpiper 5th wheel is found in black as part # LC95VR on our site.
Attached are some review videos for you to check out! view full answer...
To confirm if the Dexter Trailer Axle Beam with 4" Drop E-Z Lube Spindles # 8327812 will work with your 2022 Forest River R-Pod 202 or not, you're also going to need to verify that your spring seat-to-spring seat measurement is 74".
It also wouldn't hurt to measure the hub-face-to-hub-face as well, to ensure that your axle is 89" long.
Additionally, this axle has a 4" drop, but if you didn't need a drop axle, then you could also use the:
-Trailer Axle Beam with Easy Grease Spindles... view full answer...
I checked with Lippert Components who likely made the RV frame and structural parts in your 2005 Forest River Rockwood Freedom 5th wheel.
My contact there indicated that for your slide-out the appropriate replacement gearbox/motor is part # LC125802. view full answer...
I'd be happy to assist you. It sounds like you need the Sealed, Flush Mount Tall Rectangle LED Trailer Stop, Turn and Tail Light, Grommet and Plug, 12 Diode # STL34RB but most of the pictures I see have round tail lights like the Sealed, 4" Round, LED Stop/Turn/Tail light, 21 Diode - Red # STL55RB. If this is not the correct part, then send me a photo with the measurements of the light and we will get you what you need.
The numbers and letters that are actually printed on the light are... view full answer...
I spoke with my contact at Lippert who informed me that the 216945 that you referenced is no longer sold but there are replacement steps for you.
The Kwikee 25 Series Steps # LC3658373 will replace your steps directly. They have a rise of 8" and a run of 9" with a weight capacity of 300 lbs. My contact at Lippert confirmed this is the replacement that you need. view full answer...
It's possible that you might need a new inlet cap like part # A0120SBKVP, but it is worth noting that I believe you're filling your fresh water tank a little too much. Unless you are parking on a pretty aggressive grade or you have your tank full to overflowing there shouldn't be a leak at the cap.
When filling your fresh water you really only want to fill up the tank (without willing up the line). You want to stop filling if you have an indicator that lets you know when the tank is full.... view full answer...
The correct replacement magnets for the Dexter assemblies you have is the part # BP01-110 that you referenced as I was able to determine that with the capacity info you gave. view full answer...
For the replacement gear you will use the Replacement Entry Step Gear for Lippert Kwikee 25 and 26 Series Triple Steps # LC369354. I believe the shear pin you are referring to is a part of the gear itself. The motor is # LC369506 which comes with the smaller gear.
If you want to replace the entire assembly you can use the Lippert Components Kwikee Step Replacement Kit # LC379804. view full answer...
If you have a 3500 lb axle, you'll have a 5 on 4-1/2 inch bolt pattern. You can confirm this by measuring the center to center distance between 2 adjacent wheel studs. If it's 2-5/8 of an inch, you absolutely for certain have a 5 on 4-1/2 which is typical for a 3500 lb axle.
The # AKHD-545-35-EZ-K 10 inch hub/drum you looked at is compatible with a 3500 lb axle, it uses an L68149 inner and an L44649 outer bearing and a 58846 grease seal and has a 5 on 4-1/2 inch bolt pattern. The bearings,... view full answer...
I am sure we can help with what you need but I can't look up your axle number. Can you get me the capacity or diameter of it? That would be all that I need. view full answer...
The 2004 Forest River Wildcat 5th Wheel uses 5,200 lb axles so for brakes you can use the Electric Trailer Brake Kit part # AKEBRK-7-SA. For bearings/seals, you'll need the Bearing Kit part # BK3-310 if you have 2.125" seals or part # BK3-300 if you have 2.250" seals. In order to confirm this you'd need to measure the spindle where the seal rides or you can just get both kit and you'd have extra bearings. view full answer...
It looks like you're looking for plugs that cover the adjuster holes in a trailer brake assembly, which are also referred to as mud and crud plugs. We offer # 46-7 which is sold individually or # BP10-220, sold in a quantity of 4.
Both are compatible with Dexter 7, 10 or 12 inch trailer brake assemblies. view full answer...
Based on the pictures you've provided it looks like you have a press in wiper seal like the Rubber Wiper Seal for RV Slide Outs - Channel Mounted Press-In - 15' Long # SR94FR. We also carry this in 30' # SR44FR and 60' # SR64FR lengths.
The bulb seal looks to be a channel mount and could either be 15/16" tall and fit a 15/16" track or 7/8" tall and fit a 1" track. At this time they're on backorder from the manufacturer so an alternative would be to use a stick on bulbs seal like part... view full answer...
When replacing the fenders on your 2016 R-Pod 178 you want to choose a replacement that is as close as possible to your existing fenders. Although slightly shorter, the Single Axle Trailer Fender for Enclosed Trailer - Ribbed Steel - 13" to 15" Wheels - Qty 1 # HP66FR may still work for you.
This fender is 36" long x 10-3/4" wide x 20" tall. It is designed to fit 13" to 15" diameter wheels. As long as you have wheels this size so you won't have a clearance issue and these will work as... view full answer...
Go To Results