You are correct that you can use a 2-to-3 converter, the Curt # C56196, to separate the combined circuits on your 2009 Chrysler Town and Country so your brake lights and turn signals will operate independently of one another.
In regards to Diodes # 48955, you should use them to prevent backfeeding. I have added links to video reviews of the converter and diodes for you to check out as well. view full answer...
Converters are required when a vehicle has what is called a 3-wire or separate lighting system. These systems will have turn signal circuits that are separate from the brake light circuits.
Trailers use a 2-wire or combined system meaning the brake lights and turn signals are on the same circuit.
A converter is needed to take the separate signals from the vehicle and combine them so that the trailer lights operating on a combined system will work properly. Wires and fuses connected directly... view full answer...
To find the correct reverse light wire on your 2006 Chrysler Town and Country you will have to test the wires using a circuit tester such as # PTW2993. The problem is that vehicle manufacturers could use any color wire at any given time on the assembly line if they run out of the regular color wire they use. This is because there isn't a standard wiring color code.
I would get access to the backs of the reverse lights and test the wires coming from the backs of the bulbs to ensure you... view full answer...
Powered trailer wiring harnesses like the Curt part # C56331 that you referenced have to have the battery wire run all the way to the positive post of the vehicle battery. The reason for this is so that the taillights of the trailer won't be putting any amperage draw on the delicate taillight wiring of the vehicle. All of the amperage would be drawn from the battery instead. If you were to power the unit from a 12 volt source like what you mentioned you would be defeating the circuit protection... view full answer...
That is correct.
To install the Curt Trailer Hitch Receiver # C29UR on your 2018 Chrysler Pacifica Hybrid you will need to remove two the exhaust hangers from the rubber isolators, and support the exhaust to make sure it does not get damaged. Next you will remove the heat shield you mentioned, and will need to trim it according to the included diagram.
Once the hitch is in place, you will reinstall the heat shield, and the reinstall the exhaust into the rubber isolators. You will also... view full answer...
I attached an install picture for the Draw Tite hitch part # 76046-SK that you referenced on a similar 2020 Chrysler Pacifica for you to check out. It's not a hybrid model in the picture but it would look the same on your hybrid model. view full answer...
I spoke with Progressive Dynamics and they informed me that you cannot replace just the converter section of your 8735P and you would need a new panel, the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger part # PD4045KA to be able to charge a lithium battery.
The Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger now comes with a lithium switch. view full answer...
There is a small difference in installing the etrailer.com Trailer Hitch Receiver part # e98903 on a Hybrid compared to a non-hybrid 2021 Chrysler Pacifica. There is an emissions canister on the driver side frame rail that needs to be relocated temporarily to install the hitch.
If you check out the attached install instructions link for this hitch on this page on step 5 you'll see this outlined. view full answer...
In my research, the 2013 Chrysler Town and Country with a tow package does come with a wiring harness and should have a 7-way. To install the Dexter Predator # 58-8, you will need to run the wires from the brake controller to the 7-way connector on your vehicle.
You are also going to need Draw-Tite # 5506 which gives you the extra length you will need to hook up your brake controller to your 7-way connector.
I have attached a FAQ regarding trailer brake controller installation information,... view full answer...
The installation of the etrailer.com Trailer Hitch Receiver # e98903 will be the same as the Curt Trailer Hitch Receiver # C13383 for your 2019 Chrysler Pacifica Hybrid and I have attached the installation instructions of the Curt hitch for you so you can see exactly how to install the hitch on your Pacifica (the only difference between the two hitches is the matte black powder coat finish of the etrailer.com hitch compared to the gloss black powder coat finish of the Curt hitch).
The... view full answer...
Please see the attached installation instructions with wiring diagram for the Progressive Dynamics Transfer Switch with Quick Flip Connectors, # PD5110010Q. view full answer...
The etrailer.com hitch part # e98903 is a confirmed fit for your 2020 Chrysler Pacifica Hybrid and does have a couple extra steps for the hybrid models. There's an emissions canister that needs to be relocated temporarily when installing the hitch and also there are some holes on the driver side frame rail that need to be enlarged. I attached a diagram that shows this as well. view full answer...
I have good news for you - since you have a factory 7-way in your 2020 Chrysler Pacifica you have a very simple "installation" which will require nothing more than plugging a brake controller wiring adapter into the port under the dash of your Pacifica and then plugging the brake controller into that adapter (essentially, you can think of the adapter as like an extension cord for the brake controller).
I really like the Tekonsha Prodigy P2 Trailer Brake Controller # 90885 because it is... view full answer...
Chances are you were sagging a little below stock before you installed the AirLift # AL60814. I reached out to my contact at Air Lift and they agreed that you have nothing to worry about. view full answer...
I confirmed with Thule that you will need to use setting 10 for the FitDial on your Thule Gateway Pro 2 # TH88VR when mounted on your 2017 Chrysler Pacifica. view full answer...
That is correct, you will want to install the top straps of the Yakima FullBack 3 Bike Rack # Y02633 using the anchor method for your 2017 Chrysler Pacifica. I've installed this rack that way a few times and I found it easier to remove the hooked strap, feed the strap through the hook as outlined in the instructions (see attached), and then feed the strap up through the crack at the top of your hatch instead of trying to push the hook down from outside of the vehicle.
I actually had the... view full answer...
We have both 1-1/4-inch Class II and 2-inch Class III hitches confirmed to fit the 2018 Chrysler Pacifica Hybrid that are shown on the linked page. Both Class II hitch # C12180 and Class III hitch # C13383 will require temporary removal and re-installation of the carbon canister on your hybrid's driver-side frame rail. It will be reinstalled using hardware supplied with the hitch.
Instructions for both hitches are linked for your reference. view full answer...
The Mighty Cord RV Power Cord Adapter - 50 Amp Female to 30 Amp Male - 12" Long Item # A10-3050FHVP is for hooking up to the male 50 amp cable coming from an RV and plugging into a 30 amp female outlet in the power pedestal at your destination. view full answer...
The Curt Trailer Hitch Receiver part # C13383 is a fit for your 2019 Chrysler Pacifica and the trailer hitch I recommend for you because it has a 2" receiver tube opening and is a custom fit so no drilling is required. The hands free liftgate sensor I believe you are referring to will still work just fine with this hitch installed however, you will need to place your foot on either side of the receiver tube opening in order to activate it. This will be the case for all of the trailer hitch... view full answer...
The 2016 Chrysler Town and Country did not come with a factory installed tow package and a 7-way trailer connector. You will have to hardwire in a 7-way and the all the wiring so you can install your controller. None of the wiring is pre-installed on this model vehicle.
The first thing you will need to do is wire in a 4-way flat trailer plug if you have not already done so. You will need a wiring harness, I recommend the Curt T-One harness, # C56331. This harness is custom-fit to your... view full answer...
Go To Results