None of the Reese Goose Box models fit the Leland AF-7921 pin box wings/flanges, but there is another solution. There are only two king pins that fit the Leland bolt pattern, those being the Trailair # UF35-946208 5th wheel kingpin and the Reese # ST400-5AS16K 5th wheel king pin with sidewinder turret.
The Trailair is a traditional king pin with an air ride shock which offers a smoother ride, but only traditional limited turning clearance. The Reese 5th wheel moves the rotational point... view full answer...
As long as your spindles are 4.75 inches from seal to threading like # TRU24FR or # TRU57FR they are compatible. I've attached a photo to assist. You will be able to use the Electric Trailer Brake Kit - Self-Adjusting - 10" - Left and Right Hand Assemblies - 3,500 lbs # AKEBRK-35-SA. We do not carry a hub that will fit the bearings you referenced.
My recommendation is to change your axle or at least your spindle to allow you to use standard hubs like # AKHD-545-35-K. This will require... view full answer...
Yes, the correct replacement charcoal air filter for the Furrion microwave # FMCM15SS is the part # FR54FR. Furrion recommends changing this every 6 months or so. view full answer...
I was able to confirm that the Replacement Brushed Chrome Brackets for AirrForce RV Ceiling Fan part # 277-000399 and Replacement Blades for AirrForce 42" Hugger Style RV Ceiling Fan part # 277-000398 for cherry/maple or part # 277-94444 for black/villa will also work on the three blade models as well as the four. If you only have three blades you'd just have an extra bracket and blade. view full answer...
We have what you are seeking. It is the Oil Cap Kit 10-12K # RG04-250. It has an outside diameter of 3-3/4 inches and is specifically designed for 10K and 12K AL-KO/Hayes oil bath axles. view full answer...
Thank you so much for your photos.
We don't have an exact replacement light for you, but we have something very close. It's the Optronics LED Trailer Tail Light, part # STL13RFHXB.
This LED light measures 5-5/8" in diameter (almost exactly what your current one measures) and has the three mounting holes. It features the 7 diodes that your current one seems to have and the same three functions. Most importantly, it's round and fully red.
This is a flush-mount design, so there is a difference... view full answer...
To replace the motor in your Power Gear slide-out you can use Lippert motor # LC387523. This question has come up before, different unit but same motor, and we found out from Lippert that you can use motor LC387523 and that it may actually have more torque than the original motor. view full answer...
Last time you contacted us I sent the serial number over to Dexter and they indicated the last digit is in fact a 9. So the serial number is 3653139. I have attached the spec sheet that they sent me. The Dexter 10k axles should have a 1-1/2 inch threaded diameter the correct replacement nuts would be the # 6-96. For the Tang Washer it will be # 5-59.
We do not have a specific size listed for an outer axle nut. My guess is it would be something like a 1" ID like part # 6-191. If you can... view full answer...
Since the bags are different sizes between the two kits the mounting brackets are different as well. What that means is you can't just swap bags and would need to go with the # AL57531 if you wanted the 7500 XL kit that fits your 2019 Ram 3500. view full answer...
The Replacement Remote Control for Jensen TVs # PXXRCASA is compatible with any of the newer style Jensen TVs that have been made within the last 10 years so it will work great with your 3220, our part # JEN96VR.
I confirmed this with my contact at Jensen. view full answer...
The correct replacement converter section for your 90 amp 4500 series Progressive Dynamics panel that is compatible with Lithium batteries is the part # PD4590CSV. view full answer...
So long as your Lippert Electric Coach Step is a single or double step we do have a replacement gear, the Replacement Gear for Lippert Single and Double Electric Coach Step # LC301696.
This will be the same gear you see in the accompanying photo. view full answer...
Given the issue you described and the fact that you have done a good job of troubleshooting and checking other potential sources for the issue, it sounds like the motor is going bad. Since you mentioned the landing gear working fine for a little bit after replacing the fuse, what is likely happening is that the motor is going bad and overdrawing power which is causing the fuse to eventually blow.
The correct replacement motor for you is the Replacement Motor for Stromberg Carlson Electric... view full answer...
I've attached instructions to this question to give you a getter look at replacing the Bevel Gears # LC182851 in your HappiJac # LC736514 # LC736515. Unfortunately, I do not have a video for you but the instructions do provide good pictures.
First remove your motor using the two bolts (if you have a motor on your jack). Then take a flathead screwdriver to the top of the jack to pry out the cam lever and hinge the button from the sides of the motor cam. Grab the loose part with needle... view full answer...
Yes, if you use a weight distribution system that is rated too high for the tongue weight of a trailer the ride quality will be incredibly stiff and harsh. You want to ideally pick a system that has a tongue weight range where your tongue weight falls right in the middle.
The Equalizer Kit part # EQ37100ET has a tongue weight range of 600-1,000 lbs and would be ideal for you. view full answer...
Yes the HappiJac Swing-Out Extender Bracket for Dual Wheel Chassis Truck Camper Jacks Item # HJ54FR that you referenced is the same design as what your 2019 Northern Lite 10-2 EXCD LE has. view full answer...
The Reese Titan Weight Dist Shank - Trunnion Only - 5-3/4" Drop, 8-1/4" Rise - 1,700 lbs TW # RP54977 is a fit for your system. The Blue Ox SwayPro Weight Distribution Shank for 2-1/2" Hitches - 9" Long - 9 Hole Adjustment # BXW4028, the Curt Weight Distribution Shank for 2-1/2" Hitches - 12" Rise - 9-1/4" Drop # C17132, the Equal-i-zer Weight Distribution Shank - 2-1/2" Hitch - 12" Drop # EQ34FR, and Equal-i-zer Weight Distribution Shank - 12" Long - 13" Rise, 9" Drop # EQ94FR are all... view full answer...
The Replacement Wet Shoulder Bolt # MR52HR will replace one of the wet bolts used with the MORryde Suspension Upgrade Kit # MR58ZR on your 2022 Grand Design Imagine 2800BH travel trailer. You should also grab a Bronze Bushing # LC32SV in the event it fails as well. view full answer...
For a similar style light to the glo brite you mentioned, I recommend using the Thinline LED Trailer Tail Light w/Reflector # STL69RRXB which has tail, turn and brake light functions. This light is 15" long and 1-5/8" wide; the mounting holes are 14-1/8" apart and will match the specs on your Glo Brite 9431-55-88. view full answer...
Go To Results