The only solution I have is for a complete replacement system. Unfortunately, the Atwood Leveleg system was discontinued so there is not a replacement jack available. For a replacement, I recommend the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 4-Point Set # LC358590 if you have less than 20' between the front and rear leveling jacks. If you have 20' or more between them then you would want the 6-Point Set # LC675817. view full answer...
Hey, Scott.
I did some searching through Thetford’s catalogs and even reached out to them directly. They let me know that the 34436 toilet is no longer available, but they did give me two toilets you can use as replacements.
You can go with the Thetford Aqua-Magic in white ceramic, part # TH99SE, or the bone ceramic version, part # TH89SE. The bone ceramic is more of an off-white with a slight tan tone, while the white ceramic is the traditional bright white. Both options also come with... view full answer...
It looks like you have a Kwikee 24/25 Series Electric Step. In which case, if you need a new motor you'd actually want to go with the Replacement Motor with Gear and Table for Kwikee 24 and 25 Series Electric RV Steps part # LC369529. You can't access the nuts which hold the motor in place without first removing the table as the nuts are hidden behind this. Therefore, you'll need to remove the entire table and replace the complete assembly. I have attached for you below the write-up from... view full answer...
The Swagman Dispatch 2 Bike Platform Rack - 2" Hitches - Frame Mount # S44FR will be about 33 inches from the hitch pin hole to the farthest point of the rack. You will need to measure your tow bar to see how much actual clearance that will give you for turning clearance. This rack does have a shank rise of 6-1/4 inches, so that will possibly help with hood clearance as well.
I recommend using a shank like the Replacement Shank for Gen-Y Adjustable Ball Mount - 2" Hitch - 10" Drop/Rise... view full answer...
Hi Edward, what exactly do you mean by a hitch riser? Do you mean a high-low adapter like # RM-048-10? Can you email me a picture? The Roadmaster Falcon 3HD Tow Bar # RM27NQ is a great option with channels for cables. It will connect to any 2" receiver and then to your base plate so something like a high-low adapter doesn't require anything special on the tow bar to work properly. view full answer...
Hi Thomas; yes, the Single Zone Digital Thermostat for Coleman-Mach RV Air Conditioners # CM76RR is capable of running a furnace. This is designed to replace the following Coleman-Mach part numbers:
-7330F3361, 9430-3392, 9430A3392 (Cool Only)
-9630A3351, 9630A3361 (Heat Pump)
-9630A3371, 9430A3372 (Heat/Cool)
Do you know the part number on your existing thermostat? view full answer...
Hey Jason, thanks for reaching out!
The Dometic Penguin line of ACs has been discontinued, so we'll need to get you set up with a different AC unit. Are you looking at the Dometic as an exact replacement, or because of the performance?
We don't have any other Dometic ACs that will work, but we do have the Furrion Chill HE Low-Profile # FR76AD. This is a great alternative that has a heat pump and a single zone thermostat layout like what you're looking for, but since this is a different... view full answer...
Hey Ed, welcome back! The set screws will definitely be flush when you use the Gen-Y Anti-Rattle Reducer Sleeve item # GY22YR. The sleeve is going to be held on securely with those screws to your Blue Ox Apollo item # BX7470. I attached a picture below so you can see how it'll look installed.
The only extenders we have that fit a 3" receiver are the TorkLift Cannon Hitch Extension like item # TLE1636. However, they're designed specifically for the Ford factory 3" hitch. They're not rated... view full answer...
Phil, for your Dometic Duo-Therm you can use the Advent Air RV Air Conditioner # ACM135. This is a direct replacement for your current unit, has a 13.5K Btu per hour heating capacity, and will plug into your existing thermostat view full answer...
Hey Tony,
We unfortunately don't offer any steering stabilizers under the Safety Plus brand but we do offer some from Roadmaster that will definitely improve your handling and ride quality. For the stabilizer you'll need the Roadmaster Exact Center Steering Stabilizer # RM42RR.
For the anti-sway bars you'll need the Roadmaster Rear Anti-Sway Bar # RM-1139-149 (1-5/8" thick) and Roadmaster Front Anti-Sway Bar # RM-1139-148 (1-3/4" thick). Make sure you measure the diameter of your current... view full answer...
The Buyers Products RV Side Camera # BP68FR will fit your 2014 Newmar Dutchstar 4369 if you have the same connector as in the image below. I have no way to look up what parts were installed on your Motorhome from Newmar as most RV manufacturers do not track the parts or make the information public. view full answer...
Hey Tony, the best fitting solution we offer that has an air fryer like you are wanting would be the High Pointe part # HP36ZR which is overall 20-1/2" wide x 12-7/8" tall x 20" deep. This has a minimum cut out width of 22-1/2 inches so yours being 30 inches would be more than big enough and would work great. view full answer...
Hey Lyle, we have the Dometic Penguin II part # DMC36ZR which is a 13.5k BTU unit like what you are trying to replace. This would be a great solution that would install easily and work well. view full answer...
Hey Tim! The MaxxFan Deluxe Roof Vent # MA00-07500K is not compatible with that wall switch. I would cap off those extra wires and leave them just in case you need them sometime later on. The MaxxFan has a 2-wire design so there wouldn't be a way to connect it to that switch. Even if you could, it is designed to operate with the buttons on the vent or with the included remote. If you need anything else feel free to reach out in the comments below. view full answer...
No, I am sorry Seth the Curt Clevis Pin with Handle and Clip item # C45805 isn't rated to be used with a baseplate. For your Demco baseplate you'll need to use the Demco Standard Pins with Quick Pins item # DM9523046. view full answer...
Hey Andrew, yes the TST 570 and 770 kits are both compatible with the same flow thru sensors. The part # TST94VR is the 770 so if you have 570 sensors already this would work with them. How many sensors do you have currently? view full answer...
Hey Ken, this is a great question but the camera that comes with the Furrion Vision S Observation System part # FOS05TASF sticks out far enough away from the trailer body that your LED light would not be able to create a glare. We have a RAV4 that has this problem and it is super annoying so I get why you want to avoid it. But on the RAV4 the camera is flush with the hatch which is at exact same height as the third brake light. view full answer...
The gasket is the portion of the gate valve that's allowing waste water to leak through and not actually the gate. Both companies are using a rubber gasket that will eventually fail so it really comes down to the other features of the gate valve to determine which you'd prefer. LaSalle Bristol's cable actuated gate valves don't allow you to replace the cable if there was ever an issue, whereas Valterra's do come apart and will allow you to replace components without having to replace the... view full answer...
Hey William, the GE RV Fridge part # GE22FR that you referenced draws up to 12-15 amps which your Prowatt SW 1000 Xantrex would easily be able to power. view full answer...
Go To Results