To use the Curt Echo Wireless Trailer Brake Controller # C51180 your vehicle only needs 12 volt, ground, and turn signals connected to its 7-way socket. What this means is you do not need the brake signal from the 7-way.
For example, if you used a 4-to-7 way adapter such as # 30717, there will not be an output wire from the Echo to connect to, so you could simply tie that wire off, as you can see by the accompanying diagram.
Apart from that the only other thing required is that your... view full answer...
When we installed the Draw Tite hitch part # 76020 on a 2016 Mazda CX-9 we found that there was a distance of 6 inches from the center of the hitch pin hole out to the furthest point out on the rear bumper.
We used to carry the Yakima SwingDaddy that you mentioned and it had a distance of 6 inches from it's pin hole to the back of the knob for the swing mechanism. So you'd most likely have some contact there.
The other hitch that fits your vehicle, the Curt # C13284 has the exact same... view full answer...
Hi Dominik!
We do have 4 Class 3 hitches with 2" receivers available for your 2023 Mazda CX-9 Carbon, all of which are going to be pretty similar. I have all 4 listed below with their weight capacities:
etrailer Trailer Hitch Receiver - Custom Fit - Class III - 2" # e87AR
Towing capacity: 4,000 pounds
Tongue weight capacity: 600 pounds
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # C13284
Towing capacity: 4,000 pounds (5,000 pounds with weight distribution)
Tongue weight... view full answer...
Hello Greg,
I believe by "paddle style" you were referring to the saddle-style kayak carriers, which are flat like you described. While Thule no longer has felt carriers, there is a manufacturer that does, which is Rhino Rack. So you can still use the style you want, you'd just need the Rhino-Rack Nautic Kayak Carrier # RR571. view full answer...
Hey Jose, we sell replacement hardware for all of the hitches we carry with the part number # RHK including the Curt you referenced. view full answer...
The Rhino-Rack's Locking Fishing Rod Carrier # RR574F is great product that will work wonderfully for your application, you can't go wrong purchasing this product. This has universal mounting hardware that fits all popular roof rack bar shapes. Once installed the carrier will sit about 3-1/2-inches above the roof rack and has included locks to keep your fishing gear secure during transport. Please check out the attached product review and installation video for some helpful information.... view full answer...
Hey Melissa,
The max 42" crossbar spread of the Yakima SkyBox 18 Rooftop Cargo Box # Y07336 is actually pretty rare like what you found. The SuperLatch system that comes with this box is the only mounting hardware option for it, so there unfortunately aren't any U-Bolt kits that can be used as a replacement.
It looks like Yakima has some other roof rack options that fit your 2013 Mazda CX-9 and offer a smaller crossbar spread so if you'd like to go that route I can recommend a new roof... view full answer...
I recommend you start with the Deka 2/0 Gauge Overmolded Battery Cable Harness Assembly - Black - 7" Long # DW04363 and Red # DW04362 to connect your batteries. When wiring them as you have indicated in parallel, you will be able to easily charge the batteries simultaneously through the Buss Bar when using a charger like the CTEK MULTI US 7002 12-Volt Universal Battery Charger w/ Pulse Maintenance # CTEK56353.
You may be interested in the Redarc BCDC Dual Battery Charger # 331-BCDC1240D.... view full answer...
All of the Thule roof cargo boxes will fit the factory roof rack on your 2017 Mazda CX-9. If you are concerned about rear hatch clearance then there is a measurement you can take on the vehicle to determine which boxes will fit without hatch interference.
First, if the crossbars on your roof rack can be moved, slide the front bar as far forward as it will go. Then with the rear hatch open measure from the center of the front bar straight back to the nearest part of the open hatch. If you... view full answer...
Hello Tobey,
The U-Bolt Kit for Mounting 5,200-lb to 7,000-lb, Round Trailer Axles - 7" Long U-Bolts # APUBR-8 comes with all the hardware that you need, the (8) 1/2"-20 Hex nuts (12N) will be able to hold up to the vibrations. I do see in some reviews that some people did add washers, but it is not necessary.
What kind of trailer are you working on? view full answer...
Hello Steven, thanks for getting in touch. The SightClip Fit Kit for Yakima SightLine and RidgeLine Roof Rack Towers part # Y39AR is what you will need to put the RidgeLine towers on your 2022 Mazda CX-9 with the factory roof rails. a 50" crossbar is recommended, but if you have the Yakima JetStream bars, any bar 50" or longer will do. view full answer...
Hi Joseph; are you referring to the hardware for the # 76020 hitch that fits your 2021 Mazda CX-9? Outside of that I don't know what the 76020F hardware kit would be. If that is correct, this hitch uses ½”-13 x 1.75 Gr8 carriage bolts. If you need replacement hardware for the hitch you can use the # RHK which will also get you the washers, spacer blocks, hex nut, and pull wire. view full answer...
Hey Eric. The Miro-Flex LED Tailer Light w/ Reflector item # STL35RB has been used for years to replace/upgrade the lights that came with the Thule Transporter cargo carrier. It measures 5-5/16" x 3-7/16" x 2-5/16" deep and is sold individually.
You'll want to use either the Right Angle 3-Wire Pigtail for Optronics Trailer Lights item # A47PB or the 3-Wire Pigtail item # A45PB to install the light.
What specific Thule cargo carrier do you have? If you could put that information where... view full answer...
Hey Daniel, what you have on the roof of your 2022 Mazda CX-9 are flush rails and not raised rails. So the correct Yakima flush bar roof rack would actually be the part # Y97SD instead. This comes with all of the needed install hardware for the rack as well. What are you wanting to carry on your roof? view full answer...
If you were to run the power wire of the Curt Vehicle Wiring # 56016 to anywhere but the positive post of your vehicle battery you would void the warranty of the harness and could potentially damage the wiring of your CX-9 in the event of a short on the trailer wiring.
The purpose of the battery wire being run to the battery is so that it bypasses the delicate vehicle wiring and eliminates the potential threat of the trailer wiring damaging the vehicle's wiring. It draws all of the power... view full answer...
Hey Glen. The Replacement Carriage Bolt - M6 x 75mm item # TH915-0675-11 has a 1mm thread pitch.
What are you needing a replacement bolt for? view full answer...
I went down to our warehouse at etrailer.com to take the measurements of Curt Trailer Hitch Receiver # 13575. I know that the box that we send the hitch in will be larger than, 38 inches wide and 14 inches tall. Shipping Weight is 28 lbs or more. view full answer...
Yes it will, Mark. The Malone Profile18S Rooftop Cargo Box MPG910 will work with round, square, aero, elliptical, and most factory crossbars, so they'll work with your factory crossbars on your 2016 Mazda CX9. view full answer...
I spoke with my contact at SportRack and she stated that the SkyLine XL cargo box SR7095, will not fit a spread of 44 inches on your 2007 Mazda CX-9. However, there are other boxes that are listed as a fit to the factory crossbars on your CX-9.
I recommend the Yakima RocketBox Pro 14, # Y07192. Yakima lists this box as a direct fit to your vehicle. It is closest in cost and size as the Explorer box. I have included a link to the installation details for you. view full answer...
Go To Results