If you need replacement keys the part you need is the Rhino-Rack Masterkey Lock Barrels - Keyed Alike - Qty 2, part # RRRK***-2, with the key number inserted. Your lock core is 012 you need part # RRRK012-2. Unfortunately, you have to get the entire kit, including the lock barrels, to get the key. view full answer...
I am glad to hear you and your horses are all right after the hitch broke while you were driving!
For your 2000 Ford Excursion I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2" # C14011 as it is confirmed to fit your vehicle, and since it has a 1200lb tongue weight rating and 12000lb trailer weight rating so it will have no issues with your horse trailer with 4 horses.
I included a picture of the # C14011 installed on an Excursion for you to take a look at. view full answer...
When you are looking for a replacement axle there are a few measurements that you want to take note of to make sure that you get the correct replacement size. You want to get the same length axle that has the same Hub Face and Spring Center measurements.
From the information that you gave me, your current axle has a Hub Face measurement of 86.5 inches and a Spring Center measurement of 68.5 inches. Although we do not have any axles that have these exact measurements I do have a solution... view full answer...
I recommend either using the Demco 6K # DM8605101 if you want a standard actuator that fits a 2" hitch ball or the Titan 6K # T4745720 if you like the option of the coupler fitting with either a 1-7/8", 2", or 50 mm hitch ball. Both options have the same weight rating, fit on a 3" wide channel tongue, and have mounting bolts holes with 3" on center distances between them. I'm not exactly sure what the mounting bolt hole locations were for your Atwood 82541 actuator so if the bolt hole locations... view full answer...
I'm not entirely sure what you're needing. The # 74682 is listed as a fit for your Excursion. It is designed to plug into the round US car connector that plugs into the back of the OEM 7-way.
Further back on the wiring harness is a rectangular connector that resembles that shown on the # 118243. We don't offer that portion of the harness, if that's what you're needing, you'd probably need to obtain that from your Ford dealer.
Another option would be the # HM40975-11998. You could cut... view full answer...
We have one standard 50 mm hitch ball that you could use with the Brophy part # EH53C-C but the one you mentioned wouldn't be ideal as the bottom portion of the ball is cut flat like you noticed. The 50 mm size is pretty rare here in the US which is why we don't have a lot of options. view full answer...
I've linked our selection of LED bulbs that fit the dome light for your 2002 Ford Excursion. The most popular is part # P340921W-360. view full answer...
There are two different Firestone rear axle air bag kits for the 2004 Ford Excursion. The Excursion 2WD uses part # F2255 and the 4WD uses part # F2251. The kit # F2400 that you referenced is for Ford pickups but not the Excursion.
These two Excursion kits can be seen by clicking on the linked page. You'll notice the brackets in each kit are quite different.
I recommend that you do not try to piece together all of the individual kit parts. Often getting all of the individual parts can... view full answer...
We do have a an additional mount that you can use to install the Reese friction sway control on another trailer. You will need # RP58062.The hardware is included so you will not need anything else for the trailer side other than the sway control unit itself RP26660 when you want to tow the other trailer. One tip I can offer is that when you switch between the two trailers make sure that you adjust the sway control unit each time unless the trailers are identical in weight and size. view full answer...
For your Curt TruTrack weight distribution system, the Curt Coupler Safety Pin 1/4" # K-8P and the Replacement L-Pins and Clips for Curt TruTrack Weight Distribution System w/ Sway Control - Qty 2 # C17513 are confirmed fits. If you need more replacement hardware, you may be interested in # C17554 view full answer...
For your 20K coupler, the Replacement Master Cylinder Assembly for Titan Model 10 and Model 20 Brake Actuators - Disc # T4749501042 is the fit for your Surg-o-matic coupler. view full answer...
For mounting brackets for your Aries Round Nerf Bars - 3" Diameter - Semi-Gloss # AA213006 on your 2000 Ford Excursion, that is the Replacement Installation Hardware Kit for Aries Automotive 3" Round Nerf Bars # AA29DQ. view full answer...
The Replacement Hardware Kit for Westin Sportsman Grille Guard part # 40-022PK comes with the following hardware;
6 - M12 Hex Head Bolt
12 - M12 Flat Washer
6 - M12 Hex Nut
6 - M12 Lock Washer view full answer...
We have exactly what you need!
For a replacement upper bracket on your Firestone Ride-Rite Air Helper Springs # F2251, you will just need the part # F2135825302. This will replace 1 upper bracket for your Firestone Helper Springs to help secure it to the vehicle's frame. For the lower bracket you will use # F2135825304. view full answer...
The replacement hardware you need for the chrome Westin Sportsman Brush Guard # 45-0220 for your 2000 Ford Excursion is the # 40-022PK. view full answer...
You can certainly upgrade your weight distribution shank to fit your new Class V, 2-1/2 inch hitch and existing weight distribution head.
For your Ford F-350 Class V hitch and Reese Strait-Line Weight Distribution System # RP66084, I recommend the Equal-I-zer Weight Distribution Shank, 2-1/2 Inch Hitch # EQ90-02-4900. The rise and drop of this shank is measured with a head from an Equal-I-zer weight distribution system, but will still allow you to have a rise between 8 inches and 10 inches... view full answer...
Go To Results