To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
With a maximum gross trailer weight of 5,000 lbs and a 750-lb tongue weight, this hitch gives you the confidence to haul what you need. It’s built for small trailers, utility hauls, and fully loaded cargo carriers. The square-tube construction adds strength that holds up over time, whether you’re towing for work or heading out for a weekend trip.
The 2" x 2" receiver opening works with most bike racks, cargo trays, and ball mounts, so your gear fits without any extra adapters. It’s ideal for e-bike carriers, heavy cargo baskets, or standard towing setups. You get reliable compatibility for all your everyday and adventure gear.
No need for drilling or welding here. The bolt-on design uses the included hardware to go right on with basic tools. It’s a straightforward setup that saves time and gets you back on the road faster. Once installed, the concealed cross tube keeps a clean look while still offering solid towing performance.
The matte black powder-coated steel resists rust and road grime better than glossy finishes. It not only adds durability but also hides scuffs from daily use. You get a hitch that stays tough and keeps its neat appearance even after miles of towing and weather exposure.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi, everyone. Jesse here with etrailer. Today, we'll be taking a look at the TowSmart custom fit trailer hitch receiver on our 2018 Audi Q5. The Audi Q5 is a really nice car. It's got a really clean interior, so it's always nice to add some extra storage space onto the back of the vehicle, and adding a hitch allows you to do that. With this hitch, you can throw in accessories such as a bike rack or a cargo carrier, and you can even do some light-duty towing.
As you can see, the hitch mounts behind the fascia, so the crosstubes are completely hidden and all you'll be able to see is the receiver opening. And that receiver opening is your standard two inch by two inch that's gonna fit most of your accessories. And here, behind the receiver opening, we have a standard half inch pinhole. You'll most likely only be using this one on the rear, but that's your standard. The pin and clip will not come included with the hitch.
However, we have many options available here at etrailer. Also, any accessory that you add on will most likely come with one included. And on the bottom here, we have a wire-type safety cable loop. Very easy to access with whatever style you have. For example, this large clevis or even an S like this.
Now for some measurements, from the ground to the top of the inside of the collar is about 15 and a quarter inches. That's for your ground clearance. Then from the center of our pinhole to the edge of the bumper is about three and a half inches. You wanna keep that number in mind for any folding accessories that you might add on to make sure they don't make contact with the vehicle. And for the weight capacities, we have a gross trailer weight of 5,000 pounds.
That's the amount of weight that you can pull behind the vehicle. Then we have a maximum tongue weight of 750 pounds. That's the amount of weight pushing down on the hitch. Always be sure to double check your Audi's owner's manual to ensure that your Q5 can handle that weight seat. All in all, if you're looking for a hitch for your Q5, this is a good option for you. I like that it's hidden behind the fascia. A lot of the other options are also hidden, so feel free to check those out. But since they are hidden behind the fascia, that involves some extra steps in the installation process. You do have to remove the fascia, which can get to be a pretty lengthy process. If you're now looking to do this yourself, then feel free to check out our dealer locator to find someone local to you that's willing to help you out. If you have installed this yourself and you wanna share some tips or tricks, or maybe you just wanna share some photos of what the hitch looks like installed on your Q5, please feel free to leave a review or a comment. But otherwise, we're gonna shoot to our hitch specialist Daniel and he is gonna walk you through that install. First off, I'm gonna get a T25 Torx bit and get these screws removed under the fascia here. (tool whirs) Now, I'll be taking some hardware off of the wheel well here and just make sure you do everything you do on this side to the other side as well. And this one is a T20 instead of a T25 Torx bit. Now we are gonna be removing this rear fascia. So I taped the seams we are gonna be working with. We're gonna get this liner on the wheel well removed. So I taped this seam as well as the seam with the rear fascia and the other side of the vehicle. I got a 10 millimeter socket and I'm gonna go ahead and remove these two nuts that's holding the carpet to the wheel well. (nut crunches) There's gonna be another T25 screw that we're gonna remove (tool whirs) at the bottom of this wheel well liner. And now with that removed, we can get the carpet material and get this pushed back, and it's gonna reveal another T25 screw we're gonna have to remove. I'll get this in here. This one's about six inches from the one we just took out previous. Go ahead and take this out now. (tool whirs) Now there's gonna be two more in this same area just above the one we just took out. One's gonna be right here and then the last one's gonna be up here. (tool rumbles and whirs) Next, we're gonna want to take these T20 plastic buttons out of either side. I'll go ahead and set this to the side. Next, we're gonna take this cargo paneling out. So on the driver's side here, you can fully remove this and set it to the side. I'm gonna lift our hatch. Set that back. Now this cargo paneling can be removed, but we're gonna set this back 'cause it is connected to 12 volt power. To remove this centerpiece, I got a trim panel tool and I just put it up under here just so I can get some fingers in there. And it is gonna apply some pressure. You're gonna wanna pull up on this all the way down and I'm gonna set this to the side. Next, we're gonna find these rubber caps and we're gonna get these removed on either side. And they should reveal a 10 millimeter socket. Now I got a light and I'm shining it in the hole, and there's gonna be a hole in the top here where I can see my bolt I need to take out. It is gonna be a 10 millimeter nut here, but I'm actually going to put a paper towel in my socket so this doesn't fall where I can't get it. I'm gonna put that in there. (tool rumbles) Now I also have a magnet on standby just in case, but you really don't want these to fall down in there. (tool whirs) Now I am just gonna get needle nose and pull this out. I'm gonna do this on the other side as well. There's gonna be two more 10 millimeter nuts we're gonna have to remove. They're gonna be inside of these panels we removed. Now the hole's a little bit bigger so you could get your finger in there (tool whirs) to get these removed. Now we're gonna remove this wheel well trim piece. I am just going to start at the bottom here and pull out. Now there's gonna be some gray clips and I'm gonna push in with a trim panel tool. And once you get that one removed, kind of work your way up to the next one and do the same thing. I'm gonna push in and kind of back out like that just to get these freed. (panel pops) Once I got those first couple removed, the rest came out pretty easily, and you're just not gonna remove this whole thing just up to this T20 screw here. I'm gonna put a shop towel just to hold this in place for me and I'm gonna get this one removed. (tool whirs) Now we can go ahead and remove the fascia. I got Jesse here helping me on the other side. Now I do have a cart on standby because we're gonna have to keep the wire harness plugged in and we're just gonna swing it around and set it on this cart, but I'm gonna start in the wheel well and get this pulled out. (fascia pops) Oh, nice. Now we're gonna go ahead and take the bumper off. We're gonna use a 16 millimeter socket and get these four bolts off. (tool whirs) Now you are gonna wanna set these to the side because we will be reinstalling them. (tool whirs) (tool rumbles) And with those all removed, I can take this off and set it to the side. Now we can put our hitch into place. They do give us some welded studs, and we can set it into place while we get our hardware in. I'm gonna raise it up. Run this in a couple threads on both sides so it holds it in place. Now I'm gonna go ahead and tighten and torque all these down. (tool rumbles) Now I'm gonna go and torque these to the spec's instructions. And if you don't have a torque wrench at home, you can rent one from your local auto parts store or you could buy one from us at etrailer. Daniel got our fascia re-installed. It's just gonna be the reverse of how we took it off, but otherwise, that's gonna do it for our look at and installation of the TowSmart custom fit trailer hitch receiver on our 2018 Audi Q5.
Customer Satisfaction Score:
94% were satisfied with this product
6% of customers were not satisfied
Ratings & Reviews
Do you have a question about this Trailer Hitch?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.







Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.