To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Weather-resistant, roll-up cover keeps the gear in your truck bed secure and dry. Rolls up quickly by hand for full access to your truck bed. Aluminum slats keep cover tight and help prevent break in. Requires no drilling to install.
Features:
Specs:
Get the advantages of both a hard tonneau cover and a soft tonneau cover for your vehicle with the Revolver X4s. This hybrid tonneau likely has an identity crisis. It's built like a hard cover, but it looks and acts like a soft cover. With the Revolver X4s, you get the strength, durability, and security of a hard tonneau and the sleek look and convenience of a soft, roll-up tonneau - all while protecting your truck bed and cargo and helping to improve your fuel mileage.
The X4s has the features of the original Revolver X4 with upgrades including a matte black aluminum underbody, integrated safety slat caps, rear corner caps, and an integrated bulkhead seal.
The secret to the Revolver X4s's versatility is the aluminum slats on the underside of the cover that make it strong, seamless, and flexible. These individual, hinged slats give the cover its rugged body, while also allowing enough flexibility for the cover to be rolled up. Atop the slats is a tough, 1-piece vinyl layer that adds to the tonneau's sleek look and overall durability while also keeping the slats perfectly aligned. As a result, the Revolver X4s will roll up evenly every time, unlike ordinary soft vinyl covers that can get lopsided as you maneuver them.
Unlike other tonneau covers that sit 1/2" or more above your truck bed rails, the Revolver X4s sits nearly flush with your rails for a clean, ultra-sleek look.
The Revolver X4s gives you full use of your truck bed in a matter of seconds - just roll up the cover and secure it behind the cab. As a result, you can tote around all your gear without having to remove the tonneau. And because the Revolver X4s mounts inside your truck bed rails, you can still use your truck bed stake pockets to mount accessories like tie-down anchors.
The Revolver X4s is simple to operate. Following installation, just roll the cover out and press down on the rearmost slat at the tailgate to secure the tonneau in place. The built-in latches not only lock down the back end of the tonneau, but they also fasten the sides of the Revolver X4s along the length of the frame rails. The rail tooth runs the entire length of each frame rail. It rotates downward to lock the side rail into the sides of the cover.
When the cover is rolled out and the rear slat is pressed down at the tailgate, the latches on both sides engage. When this happens, the integrated teeth pivot down and rest on top of each slat of the rolled-out cover. Closing the rear slat effectively pins the cover to the rails, ensuring that the cover stays closed from front to back. It's that simple - no Velcro to seal or snaps to wrestle with. When your tailgate is closed and locked, no one will be able to get through the cover, thereby safeguarding your truck bed and its contents. The cover automatically secures as the locking levers at the tailgate engage. These sturdy levers have reinforced gussets that give them added strength and durability. And they will never need adjustment.
To roll up the cover, unlatch the rear slat by dropping the tailgate and pulling either of the 2 release cords located along the bottom corners of the slat's housing. Either cord will release both of the latches so that you can raise the rear slat. When the latches are disengaged, the teeth roll back into the frame rails, releasing the sides of the cover so that you can easily roll it up. Just fold the rear slat over and roll up the cover the rest of the way.
Then secure the tonneau behind the cab with built-in nylon straps and sturdy plastic buckles. These straps help to keep the bundled tonneau from contacting your cab while you drive. And 4 rubber bumpers act as cushioned barriers between the cover and your truck cab.
The Revolver X4s's rugged aluminum and vinyl construction makes it an ideal match for your truck, no matter what you do while at work or play. This cover is strong enough to hold up to 400 lbs of evenly distributed weight when it's rolled out. The 1/4" thick, aircraft-grade aluminum slats are covered with a matte black vinyl skin for superior resistance to impacts, UV rays, and weather. This skin is what gives the tonneau its soft, sleek look. While the Revolver X4s may look like a soft cover, its aluminum skeleton provides exceptional security because it cannot be cut through in the same way that a standard soft vinyl cover can be.
Felt strips on the underside of the tonneau help to keep the slats from scuffing the vinyl top as you roll up the cover. The soft felt also shields your hands when the cover has gotten hot or cold. And rubber strips overlay your truck's side rails, cab rail, and tailgate, creating a seal that helps to conceal any gaps and works to prevent water from seeping in.
Easy, No-Drill Installation
Installing the Revolver X4s is simple. All you need is a wrench, and you don't have to do any drilling. The tonneau's frame rails clamp to the inside of your truck bed side rails to create a base for the cover. The included bolts secure the front hinge rail to the frame rails at the cab.
Slotted brackets at the ends of the tonneau side rails allow the bolts to shift in case you need to adjust the cover to achieve a snug fit. These brackets ensure proper alignment of the tonneau frame on your truck bed side rails. This eliminates trial and error in installing your rails - you won't have to put them on and then take them off again to get the correct fit. Pre-installed shims and spacers also help to ensure that the Revolver X4s rails are installed squarely on your truck bed.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi everyone, it's Evangeline. And today we'll be taking a look at the BAK Revolver X4s, a premium tonneau cover. So we'll take a look at some of its specs and measurements right here at etrailer.com. So this has the best of both worlds. It looks and works like a soft tonneau cover but then you have the benefits of a hard rolling tonneau cover. So we'll talk about how that works.
And then you can see on our individual pages here at etrailer if it fits your specific truck. So if you're familiar with the Revolver X2, this is going to be the upgrade. And you can tell because of its matte black finish. So if you see something like this driving down the highway, you'll know that it's the Revolver X4s. This is extremely low profile.
So we have this installed on our 2022 Ford F-250. The installation is gonna be different depending on your truck. But if you're curious to see how it works, you can check that video out here at etrailer. But see here on our truck bed how much rise we have, pretty much none at all. Let's take that measurement.
So you can see here how our rails go up here. And then we have the tonneau cover itself being the highest point. And even at its most high point, it's barely a quarter of an inch above our truck bed. So the rail itself is gonna be two inches out. So even that doesn't decrease your actual usable space.
So speaking of flush against our vehicle, notice the way this sits right up at our tailgate. So if you have your tailgate closed you also close the access to your tonneau cover. Awesome if you have important items inside and you wanna keep them secure. And when you wanna open up your tonneau cover, you just open up your tailgate and then you are able to open up that latch. When you got whatever you needed, go ahead and slam your tailgate on it. Just like that, you can see how everything is low profile and flush. So you can actually close this with your tailgate open or your tailgate closed. The way this works is we have that latch system. You just pop them into place, push down. You are gonna have to latch it on both sides. There's also gonna be a string over here which allows you to open up that latch on both sides. So if you're accessing it from the passenger side or the driver's side, you just pull that string, pop right open. So this just rolls along on the rails. So when you're unrolling it, you just bring this back in and it pops into those brackets. You lift it back up and it continues to offer you access to your truck bed. So this creates a very smooth cover on top of your truck bed. So you can see how it blends a soft tonneau cover with the benefits of a hard tonneau cover, like a soft tonneau cover you have that nice matte black finish, but with it blended with the aluminum you actually have 400 pounds of weight capacity evenly distributed on the cover itself. And that also solves the issue that soft tonneau covers have. Some of them, you just rip open that vinyl and people could get access to your cargo on the inside. Since this is hard all throughout, they have that security feature there and you feel better about whatever you're storing in your truck bed. Now, what if it rains or pours or snows Well, you can see here with the rubber seals on each side it creates a weatherproof cover. So with that rain coming down this will drain on the inside, or it will go down the cover, down the rails and right off of your truck bed. Make sure to have everything sealed on the inside. This does not include drain pipes because really, water shouldn't be getting inside in the first place. This rolls up all nice and neat against your bulkhead. You do have straps to secure in the open position. So those secure right up there and then you can see here as well that this does not take up any space underneath or inside of your truck kit. So compared to canister style tonneau covers where they roll up underneath the bed, this one goes up on top. So let's take some measurements to see how much height this is gonna add. Now this will be a little different depending on the truck you have that's installed on but on our F-250 that's pretty much how much height it's gonna add which is from the top of our bed to the top of the roll is eight inches. So if you have a longer bed, it might be a little bit more but still very low profile for a rolling tonneau cover. So this is the style of strap it's gonna use to secure the tonneau cover. I personally prefer something a little bit more secure since this is a metal buckle. So just make sure to tighten down both sides. That way there isn't any movement of the cover itself as you drive around. Having it rolled up like this is also a perfect way to see how we have those different layers. So this is the flat design, which allows you to roll this up and still maintain the hard tonneau cover benefits but still have the soft tonneau cover maneuverability. Then you can also see the rubber seal on this side giving it that weatherproof experience. So this is gonna include pretty much everything you need to install this on your vehicle, but there may be some differences depending on your different trucks. So try to check out our fit guide here at etrailer, that way you can see if we've tried this tonneau cover out on your vehicle and show you the process of how it goes. Now, this includes the bumpers. This includes the straps, things like that. What doesn't include, but I recommend adding on is gonna be a 9/16" socket. This may need another socket size or multiple other tools. So check out those instructions. You're also gonna need some measuring tape just to make sure everything is square. And depending on your truck, you may even need some extra shims if things are not aligned for your truck bed itself. So definitely check out whether you have things like a drop-in liner, the length of your truck bed as you use our fit guide to get the best fit for you. So I've installed a couple of different tonneau covers before. So I have some personal thoughts about this one. And the main thing is that this is probably one of the most low profile tonneau covers I've seen. You can see how it's super flush with our rails. And I really like the concept of a soft tonneau cover with the benefits of a hard tonneau cover. Since we have it where it doesn't take up too much room behind your cab, you get the full access to your truck bed. As you can see here, we have a fifth wheel hitch inside of our truck bed, and we still have access to the side of the bed like those slots or those stake pockets to install a ladder rack. So this opens up a lot of options because you don't need to get extra lax. You don't need to worry about security. You don't need to worry about someone seeing your fifth wheel hitch and being interested in it because you have this tonneau cover on top, protecting it nicely, securely and with style. With this right here was a look at our BAK Revolver X4s premium tonneau cover right here at etrailer.com. My name is Evangeline, and I hope you enjoyed the journey..
Average Customer Rating: 4.5 out of 5 stars (84 Customer Reviews)
Weather-resistant, roll-up cover keeps the gear in your truck bed secure and dry. Rolls up quickly by hand for full access to your truck bed. Aluminum slats keep cover tight and help prevent break in. Requires no drilling to install.
Still covers the bed, no problems after a year
Easily installed. Meets all expectations. Already recommended to a few people.
love the cover no leaks easy to roll up when you have big loads easy to roll back and fasten. love it.
I have been very happy with this cover. It has been secure and keeps most water out when it rains. It is holding up very well.
I love this cover! It is well made and I was able to install it in 20 minutes. After a year it looks brand new and I've had no issues with it.
Thanks Lisa D for recommending this cover!
Install was easy, looks great!
Fits great after I figured out that I needed some shims. It nice not to have to worry about items in the back of the truck.
GREAT PRODUCT. I LOVE IT!
Very easy to install. Package arrived e arly.
Carrie’s customer service and the products. I’m gonna be a repeat customer.
The cover has held up well, I would purchase again. A couple small items could be updated from the factory but overall its a nice cover.
I saw mixed reviews but took the chance and I regret it! The felt on the inside came off and has made the cover hard to use ripped off only a few short months after I got it. The company sent replacement felt which is going to be a major pain to replace. It also only does an “ok” job at keeping out water. It’s not a single hand open using the wire like it says. Only advantages is that it rolls up to keep majority of the bed open and you can set some stuff on it.
I like that it has the aluminum to keep it a little sturdier than other roll up covers. But I do not like that it leaks by the tailgate and at the top corners close to the cab.
It was easy ti install. I had it for a year and it still looks new. The only thing it needs is a seal for the tail gate. But it only leaks when seating still the rain blowing at the back of the truck or going thru a car wash. Would recommend it, the leak has never given me a problem.
Works great! No issues.
The top is very nice looking and the installation was very easy. The product was engineered well to fit my truck beautifully.
Two issues though...it came with some minor scratches and it leaks at the front corners.
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.