To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
When you need to haul larger gear or bulky materials, there’s no need to remove the cover. The LiteRider rolls up in seconds, peeling back smoothly from the Velcro seals along the bed sides. Quick Clip straps keep it secured behind the cab while you drive, leaving your rear window clear and the side rails open for stake pockets and tie-downs. It’s a simple, no-hassle way to switch between covered storage and full bed use.

Rain, snow, and dirt stay out thanks to the reinforced vinyl flap along the tailgate and the double-coated, UV-resistant vinyl top. The material stays flexible down to -40 °F and won’t shrink or fade from sun exposure. Whether it’s freezing cold or blazing hot, the cover keeps its shape and shields your cargo from the elements.
Covers that loosen or flap in the wind can be frustrating. The LiteRider solves that with EZ-Dials at the front of the bed. Just turn the dials to fine-tune the fit—no tools needed. The even tension keeps the cover pulled tight for a clean, low-profile look and smooth rolling every time.

Once the cover is rolled down, the AutoLatch automatically catches and holds it shut. A simple pull-cord releases it with one hand when you’re ready to open up. For added peace of mind, there’s a slide lock on the opposite side that pairs with a tailgate lock (sold separately) to keep your gear protected when you’re away from the truck.


The contoured black powder-coated aluminum rails resist rust and mount inside the bed rails using aircraft-grade aluminum clamps. Their Tight Bite design grips firmly to the rail ridges for a solid hold. The setup leaves your stake pockets free for accessories and gives the cover a streamlined 1-1/2" profile above the bed for a clean, finished look.

Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
If the cover comes with an element seal gasket, cut two 1 1/2 inch sections, and place them to fit the gaps between the front bulk head and the bed rail. Loosely assemble the brackets to the rails using both flat washers, lock washers, and nuts. Remove the plug at the end of the channel. Slide the carriage bolt bracket and bolt into the channel of the Utili-Track, with one set per rail bracket. Position the side rail with the weather strip against the inside lip of the box. Line these carriage bolts up with the brackets, and secure them with these serrated nuts.
Just leave them finger tight for now. Push down on the rail so you fully compress the seal while you tighten the rear serrated nut to fifteen to twenty foot pounds. Make sure the rail is parallel with bed caps, then tighten the front serrated nut to fifteen to twenty foot pounds. Push the rail towards the side of the bed to compress the seal, and tighten the bolts left loose in step two. Now repeat all these steps with the second cover rail..
Ratings & Reviews

William
12/13/2024
Have had the cover for 2 years and it is still in great shape and it looks like new. Definitely worth the price!!

Brooke M.
3/1/2025
Thats great to hear! What will you be towing or carrying with the new addition?

Mike Q.
12/21/2020
Cover is showing wear from being rolled up to tow 5th wheel. Even with it strapped tight. Hoping it doesnt wear through

Jenny N.
3/7/2022
You mentioned that the tab on the cover had rubbed the paint off on your truck. I wanted to see if would be able to send a picture?

Glenn
3/7/2022
I will take one and send it to you as soon as I get a chance
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.






Tyler M.
12/8/2020
Hi Lee, Thank you for your comment. The owners manual for the cover says that if the latch system doesnt engage, then the first step is to check the side rails for height and level, referring back to a step in the initial setup process, as well as inspecting the latches for jammed or broken parts.