To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
When you load up the bed or hook up a trailer, rear-end sag can throw off your balance and steering. The Timbren Rear Suspension Enhancement System adds up to 7,000 lbs of rear-axle support so your truck stays level and stable. Each hollow rubber spring sits above the axle to share the load, keeping your steering, braking, and ride height consistent even when towing or hauling heavy gear.
Rough roads and bumps can wear you out fast. Timbren’s hollow rubber springs act like built-in shock absorbers, taking up road impact before it reaches the cab. The progressive design compresses easily over light bumps and stiffens as weight increases, giving you a comfortable ride no matter what’s in the bed. The rubber construction works quietly and helps extend the life of your factory suspension by reducing bottoming out.
Cornering or swerving with a heavy load can cause body roll and sway that unsettle the whole setup. These springs work independently on each side of the vehicle, so when one compresses, the other stays steady. That independence keeps you level when turning or carrying off-center loads and helps the trailer stay in line when wind or passing traffic tries to push it around.
There’s no need to chase leaks or run compressor hoses here. Timbren’s custom-fit brackets bolt directly onto the frame rails above the rear axle and replace the factory bump stops—no drilling required. Once installed, the springs automatically engage when you need extra support and stay clear when you don’t. It’s an easy, low-maintenance way to keep your truck ready for any load without extra hardware or tuning.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Jeff: Hello everybody, this is Jeff at etrailer.com. Today we're going to take a look at this Timbren rear suspension enhancement system. Now this is a custom fit part, it is designed to fit the 1991 to 1996 Spartan EC2000 motorhomes with the round axle, also works on the 1997 to 2007 Spartan EC2000 motorhomes. Now on a custom fit part like this, I always like to recommend for you to go to our website, use the fit guide, put in your year and model vehicle, and it'll show you if this will work for your application.Now this kit will improve the suspension, handling and safety of your vehicle, provides additional support as needed, so you always have a nice, smooth, comfortable ride. Basically, it'll allow the leaf spring ample movement while cushioning light loads so it does not affect the empty ride of the vehicle. It will become more rigid as more weight is added.
This will increase stability, provide great performance while hauling heavy loads, and it will even help reduce vehicle sag. These do work independently side-to-side, they'll help compensate for any off-center loads, and it reduces body roll when you're swerving and turning corners. They will act as shock absorbers, taking the brunt of any bumps and rough roads, helps extend the life of your vehicle's suspension.This kit will include everything shown here on the table, the two Aeon hollow rubber springs, the vehicle specific brackets, and the hardware needed for installation, comes with a nice set of detailed instructions. Basically this part will replace the axle bump stops on your frame, so there's no drilling required. Capacity on this is 7,000 pounds.
Now these Timbren springs will not increase your vehicle's weight carrying capacity, so you do want to make sure not to exceed the manufacturer's recommended weight limit. And these are designed to work with a suspension system that is in good working order. But that should do it for the review on the Timbren rear suspension enhancement system.
Ratings & Reviews
Installed on 2025 Ford F550. Installation was easy took about 2 hours to do front and rear bump stops. Used the supplied spacer ended up raising rear about a 1/2 inch which was the same as front. Purchased these due to truck sitting 1 1/2 inches lower on passenger side when Host Mammoth was loaded ( scaled at 18,600 lbs. with all tanks full). Didn’t have any excessive sway or bounce just not sitting as level as I would like. Did notice truck hitting bump stops a few times on both ends hoping theses smooth out the occasional bottoming out. Will update after I’ve loaded camper and made a few trips.
It arrived quickly and installation was easy… I’ll wait to see how it performs, but for now, it looks great and fits very well… thank you very much.
Photos before and after
I installed these on three different trucks in a year, a 24 F350 CCLB Gas SRW to use with a smaller 9.6 Northern Lite truck camper, but decided I wanted to step up to a DRW, as I bought Northern Lite 10-2 instead. I traded that SRW and put these on a new 24 F350 diesel dually. Took that truck and 4000lb camper coast to coast and back. This year I traded that 24 F350 on a 25 F450. The Timbrens needed a 1" spacer for the F450, as the spring blocks are different. I called Timbren, and they sent me the spacers and longer bolts free of charge. Three trips so far this year with the truck camper on the F450. Couldn't be happier with the Timbrens. They have about 3/4" space when not loaded, so there is free spring movement, and they help with sway and level when loaded. I also added overload spring blocks of my own making, similar to the ones Timbrens sells.
Jesse M gave me expert advice and answered all my questions regarding the Timbren rear suspension enhancement system. I ordered the Timbrens and it took me a little over half an hour to install myself. I absolutely love the way the Timbrens leveled my sagging truck and greatly improved the stability of my ride. I carry a 2003 Northstar tc1000 pop-up camper on my 8ft bed. I highly recommend the Timbren rear suspension enhancement system. I attached a before and after photo.
Feels like it was a real help on the suspension but need about a year to get the full opinion on different roads.
Received the Timbren SES kit in today's mail around 11:30AM, already installed on my 2024 F-150 pickup's rear differential before 3:00PM same day. Like always etrailer's fast delivery time and product info with installation video on your website are very helpful. 1st photo OEM bump-stop, 2nd photo OEM bump-stop removed, 3rd & 4th photo Timbren SES kit installed.
Accolade XT 35L - Timbren SES (TFRSDE - 12k support) loaded in the sweet spot.
These Timbrens should be used on F600 and F550 models. Do NOT use the spacers that come in the box. Just install the Timbrens without the spacers and you are good to go. When FULLY loaded (full gas/water and gear), the Timbrens should compress about 1/2”, which seems to be the sweet spot. The end results are as follows:
1. Better bump absorption and much better rebound. The inside chatter is more of a low sounding rumble and the suspension rebound is really quick.
2. Much better sway control and overall stability.
3. The drive feels more balanced front to rear. The rear drop was reduced by 1”. I think that allows the leaf springs and shocks to work in a more neutral position.
These are worth every penny and are a cheap “set it and forget it”way to improve your ride quality!
Added these to my F250 Super Duty. I carry a golf cart on a Diamond back bed cover. Can be a little top heavy. Perfect addition to my suspension- greatly reduced the sway.
Easy to install using basic hand tools, and stopped the "sag" when I hook up my Casita travel trailer
Helps prevent about 1/2" of sag with my 175lb-tongue weight trailer and easy to install.
Great product. The ride and body roll at the rear axle are notceably improved (1989 Ford E350 Class C RV , 27 ft). I give it 4 stars because the installation was slightly complicated due to the rear brake lines needing to be slightly bent to provide clearance for the U bolts supplied in the kit. Great product and wish it came in a 5000 lb version.
2,000 miles in on a trip from the east coast to the Canadian Rockies these work great while loaded and towing. Close to zero bounce while towing, I love them. Unloaded, however, the ride in my 2026 Tundra has gone south. There is a noticeable, abrupt stop of the units hitting the axle when going over any kind of bump. When I get home and back to regular driving, I may just take them off, its that bad.
I've had these on our tow rig for a year now and I added buy them again today if I needed them.these have worked much better than airbags for our coil spring rear suspension to handle the tongue weight of our trailer. The SUV sits level when the trailer is on and it handles bumps and sway better than the airbags did providing much more comfort to us in the vehicle. Unloaded, we don't really notice they are there, unless, we have all the kids and some friends loaded up and you will fell them work when going over bumps.i do all my maintenance on the vehicle's and inspect these regularly and I cant see any wear so far even though we've gone on 6 trips with our trailer with about 5000 miles doing so.
I cant say these are the best for every truck or SUV, but for ours it is the best and I definitely would recommend to others.
Order came fast and right. E-Trailer gets it the first time !!
Installed fit perfect
Well they are exactly what I thought it would be. Hard for me to say it's what I needed yet.
I installed them on a homemade trailer from a salvaged 2001 base model tacoma. Once I get finished building it out and have some weight in it I'll have a better idea. But from what I've seen so far on a couple test drives they should come into effect when needed.
For reference I building an Tacoma based trailer with an ARE Contractor topper with a Naturnest roof top tent on the very top. So to counter and sway these should be very helpful. At least I hope so. I'm not an engineer but I did stay at an Holliday Inn once.
The Timbren SES is a simple solution for rear squat when towing. When hitched to my 30' Airstream Globetrotter (8800 GVWR) with a tongue weight around 1200 lbs, my Silverado 2500HD had a bit more squat than is ideal. I shopped airbags but didn't want to spend ~$2K for the set up and didn't want the hassle of installation and forever chasing air leaks. The Timbren SES literally installs on the Silverado in about 15 minutes. So simple. No bags, no compressor, no wiring, no air lines, no leaks. And WAY less expensive to boot. Just returned form a 600+ mile trip and it towed flawlessly.
A very simple and straightforward installation once you get the oem bumper stops off (had a shop do that)
Timbren worked with me as I had a non OEM frame height (vehicle was lower than stock) to recommend the proper kit. Highly recommend contacting timbren if you are unsure of the proper kit to use. Ride is more stable. It does feel stiffer and less bouncy but am looking forward to seeing how it performs with my truck camper. Truck is a 1998 dodge ram 2500. Brake line over left side of axle needed to be secured to prevent damage.
The Timbren overload spring/bumper was east to install and did what it was supposed to do when I hitched up a camp trailer. These did not negatively affect the ride by any means and I don't have to worry about the troubles with air bags.
Stiffens and corrects kneel in rear end of 2023 Chevy Silverado 1500. You will notice a stiffening of the rear end suspension while unloaded, but it’s a fair trade off to prevent sagging and porpoising while towing. I found it easier to pull the rear wheels and work from the side than underneath the vehicle while installing.
The timbres bump stop is exactly the right height to meet the axel when the trailer is connected with all its weight onto the hitch. I have an Andersen weight distribution hitch and it levels out perfectly. The day picture is with the coach (Winn 2100bh) with factory equipment. The night picture is after the timbres are in place. Looks good.
It has been almost a year since I installed Timbren Suspension Enhancement Systems (DVF350 and DVR350R) on the front and rear of my 2003 Dodge RAM Van 3500. These bumpers replaced the OEM bump stops that were on my van. I like the Timbren bumpers much better than the OEM bump stops because they provide a progressively cushioned response for suspension compression when traveling over significant humps like speed bumps in a parking lot, or curb ramps into driveways. I did not like the abrupt stop the OEM bump stops provided when traveling over the same objects. I installed the Timbren rear bumpers first, and after a few months of use, I decided to add them to the front. In both cases, the front and rear Timbren bumpers were easy to install once the OEM bump stops were removed. Installation required reuse of the factory hardware. On my van, the Timbren bumpers are not always engaged. Under normal load and travel conditions the bumpers are relaxed and about 1/2” away from the suspension landing points. However, their presence is much appreciated and very noticeable when the van is carrying heavy loads or handling significant humps.
2022 F250 Super Duty. Super easy to install. I have about 3/4" gap between the spring and the plate. Time will tell how they impact the ride quality and how much sag they mitigate with my 5th wheel hooked up.
Great upgrade when pulling our 6500lb travel trailer. Helps with sag and control on the road on our Ram 1500. Change the stock shocks and if you choose, upgrade your stock springs, and you'll get the most out of your half ton.
Absolutely Pleased with the TIMBRENS. They were easy to install, and took less than an hour to install both. I noticed a slight stiffness in the ride as the rear bounced over a bad roadway. Towing is great, with a nice level and smooth ride. I am glad that I did not order the heavier duty Timbrens, than what was recomended for my truck. I believe the ride would have been too stiff. If you look at the photos showing the timbrens, the truck is still lifted in the rear, so what you see is a big gap between the rubber, and the steal plate. When the truck is lowered, there's 1" of space as it should be. BTW, I have been purchasing from etrailer for years now, and I have to say that I have never had any issues with any orders. They are my go to folks for all of my vehicle suppension stuff and trailer stuff. You can't go wrong with buying from them.
Easy install took about 20 minutes on my 2017 Ram 3500 SRW. Had about 1/2 inch clearance as recommended. Loaded up my 5th wheel (2350 hitch weight) and about 200 lbs of gear in the bed. Just got back from a 800 mile camping trip through mountains of TN. You can really feel the difference around those sharp corners and uneven surfaces. The truck felt firm and controlled not hard and jarring as some have mentioned. Going over those overpasses with the wonderfully smooth (Not) joists was greatly improved. The truck would squat and rebound again, with a firm controlled response. Driving without a load felt the same as before without them. I would highly recommend these! Ordering from etrailer continues to be my go to option!
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.