1. Roof Rack
  2. Thule
  3. Fit Kits
  4. 4 Pack
Fit Kit for Thule Evo Clamp Roof Rack Feet - 5069

Fit Kit for Thule Evo Clamp Roof Rack Feet - 5069

lowest price pledge
Our Price: $129.95
You Save: $10.00
Roof Rack

Will this fit?

To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.

This item qualifies for Free Shipping
Shipping Weight: 1.95 lbs
Thule Fit Kits - TH145069
zoom in icon
slider vertical icon
zoom out icon
Comment field cannot be left empty.
Name field cannot be left empty.

Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.

Error submitting comment. Please try again momentarily.

Product Images


These custom clips and pads let you mount Thule Evo Clamp feet on your vehicle with a naked roof. The rubber-coated steel clips are easy to install - just slide them into the feet until they click. Rubber pads help protect your roof from scratches. Lowest Prices for the best roof rack from Thule. Fit Kit for Thule Evo Clamp Roof Rack Feet - 5069 part number TH145069 can be ordered online at etrailer.com or call 800-298-1624 for expert service.
  • All Info
  • Reviews (2)
  • Q & A (3)
  • Videos (1)
  • Photos
  • Why etrailer?

Thule Roof Rack

  • Thule
  • Fit Kits
  • 4 Pack

These custom clips and pads let you mount Thule Evo Clamp feet on your vehicle with a naked roof. The rubber-coated steel clips are easy to install - just slide them into the feet until they click. Rubber pads help protect your roof from scratches.


  • Custom-fit clips and pads let you mount Evo Clamp feet (sold separately) on your vehicle with a naked roof
  • Clips are quick and easy to install - simply click into place
    • Steel clips provide secure grip on your door jambs
    • Rubber coating protects door jambs from scratches and abrasions
    • Powder coated for durability and rust resistance
  • Molded rubber pads fit the contours of your roof
    • Clip onto bottoms of feet
    • Protect roof from scratches and abrasions


  • Quantity: 4 clips and 4 pads
  • Limited lifetime warranty

Secure, Click-In Installation

Thule Fit Kit Clamping to Vehicle

The fit kit clips are easy to install on Evo Clamp feet. Simply remove the lockable covers on the feet, then slide the clips into the clip retainers. The clips will click into place when properly installed.

Thule Fit Kit Single Attachment Point

To complete installation, place the fully assembled rack on your roof at the location specified in the fit kit manual. Tighten the rack in place with the torque tool included with the Evo Clamp. The single attachment point bolt lets you quickly secure the crossbars to the feet and the feet to your door jambs simultaneously. An audible click from the torque tool indicates the rack is secured properly.

Protection for Your Roof

Thule Fit Kit Rubber Pads

The rubber-coated steel clips and molded rubber pads protect your vehicle's paint from scratches and abrasions. The pads easily slide onto the bottom of each foot, and they are specifically designed to fit the shape and contour of your roof.

145069 Custom Base Clips and Pads for Thule Evo Clamp Roof Rack Towers - Qty 4

Replaces Thule THKIT1711

Item # TH145069

Installation Details TH145069 Installation instructions

Video of Fit Kit for Thule Evo Clamp Roof Rack Feet - 5069

Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.

Video Transcript for Thule SquareBar Crossbars Installation - 2019 Hyundai Elantra

Today we have a 2019 Hyundai Elantra and we're gonna do a test fit of the Thule Square Bar Crossbar Roof Rack System. As a roof rack mounts to the roof of your vehicle and allows you to get your favorite accessories on top of your roof, whether you wanna carry a bike rack, a kayak or even a smaller cargo box.It's made up of a couple of different components. First up top we have our 53 inch square bar crossbars. Now Thule has redesigned these so they do look pretty nice and what, in my opinion, is the coolest feature is that rather than having a foot pack that's special for the square bar, they actually have an included track in the bottom and now these Evo feet are gonna be able to fit your square bars and your wing bars.Now leading into our Evo feet for naked roofs, this is basically gonna be the middle man between the crossbar and the fit kit. The foot is going to install into that track and it's going to be tightened down right here using that bolt on the inside, leading down here to our thicket, we have a rubber coated hook that goes under our door frame. We're gonna have this nice thick rubber pad that's actually designed to fit the contours of our Elantra.

You can see that little lip that goes over the side. It's completely flush all the way around. Thule's really just gone out of their way to make sure you get that exact fit on your roof rack.Now the way that hook is gonna work is that when you open up the door you can actually see that it comes right under that door frame right there. It's again, custom fit to match those contours to make sure you get that nice snug fit. Once it comes up and tightened down, it basically pulls the hook up into the foot pack.

Then we put our end cap back on. We're also gonna see we have these plastic locks that can be replaced with Thule lock cores which are sold separately here at etrailer if you want more a secure fit for your roof rack.Now let's go ahead and give you some clearance measurements. First from the top of our roof to the bottom of our square bar, it's gonna be 3 inches which is more than enough space to get any clamp on accessories or accessories with rubber coated steel straps under the crossbar without harming the top of your roof. Now from the top of our roof to the top of our square bar, it's gonna be 3 7/8 inches, which you wanna keep that in mind because that's how much height you've added to the top of your vehicle. With your Elantra, you may never run into those situations but just in case you ever do, keep in mind that's how much you've added.

It's also gonna have a 220 pound weight capacity which is a step up compared to some other roof racks out there, but do be sure to double check with your Elantra's owner manual to make sure your roof can handle that weight.Now you see my front bar is installed already. The rear one's gonna install and assemble the exact same way. I've got it partially assembled on my table. Let's go ahead and get it the rest of the way. So we just flip our square bar over.

First thing we wanna do is grab our Evo foot. I'm gonna take the pad from our fit kit and you do wanna make sure that you get the correct number pad, the number is gonna be on this corner. It's engraved in there, if you can't see it on camera just get it in some light and you'll see it. Just pay attention to your instructions on where it goes based on front right, meaning passenger, or front left meaning driver side. So just push that pad on til it clamps itself on. Now from there we're gonna grab the hook that comes in our fit kit and again, these are numbered. It's right on the inside. You can hardly see it without having some type of light to reflect off it, although with our Elantra it's all gonna be the same number so you don't have to worry about it. What we're gonna do is push it into that slot and just push til you hear a click. There, give it a couple tugs and we'll see it's locked in place.Now let's come over to the side of our crossbar, we need to pull the end cap off. Then what we're gonna do is push in on these two silver buttons right there. When we do that's gonna unlock the channel lock right there, give you an example. See that part comes up, unlocks right there. So we need to make sure that the hook is facing the outside. We have this scale right here that we talked about that they included on the square bar. We need to go to the number they specify in the instructions. Once you have that number, just go ahead and go to that mark. Then once you let go of those silver buttons, it's gonna lock into place. So now I can't move it at all unless I push in on the buttons. Just put your end cap back on. Now we're ready to get it on our roof.Now we can get our crossbar on our roof. Again, you wanna make sure that the side with the pad goes on the correct side. So I found the number that goes on the rear passenger side. I'm gonna get that other hook in place and then just set it down. Now we're gonna have to go grab our measuring tape so we can measure our crossbar spread. What we're gonna do is measure from the front of our front crossbar to the front of our rear one. Again you can find this measurement in your instructions. You wanna make sure you get it as close as possible on both sides. Scoot it up a little bit. Now we've already gone ahead and measured the other side, but you do wanna be sure that you go and double check 'em both before you start to tighten down.Now with our included tool we're gonna go ahead and start tightening down our roof rack system. You see the hook has a lot of slack right now, what we're gonna do on both sides is first tighten it up until that hook just is sitting at the bottom of the door jam to where it's not really tight at all, not even snug. We just want it resting right there. So we're gonna go until it gets to that point. This is just simply to make sure that it as a hold of something when you're tightening it down. It's making contact, there's no more slack. Let's go do the same on the other side. Now that we have both hooks just making contact with the bottom of our door frame, we're gonna go ahead and start tightening down. Now you don't wanna do all of that on one side and then go to the other, you wanna do a couple turns or a couple rotations on one side and then move to the other one. This is gonna ensure that it doesn't pull too much on one side when you're tightening down. Let's go ahead and go a couple rotations in. I'm gonna go to the other side.Now we have the other side tightened down all the way. I'm gonna show you how we knew it was tightened down all the way. We just kept going back and forth and then we heard those audible clicks that let's you know that it's torqued down to the correct specification that Thule has. We're gonna remove our tool. I'm gonna shut our door. Then you do wanna go ahead and give your roof rack just a quick shack and make sure that it's tight and it's secure. Then once you're done with all that, just put on your end caps and you're ready to load up your favorite Thule accessories and then hit the road.That's gonna do it for the test fit of the Thule Square Bar Crossbar Roof Rack System on our 2019 Hyundai Elantra.

Customer Reviews

Fit Kit for Thule Evo Clamp Roof Rack Feet - 5069 - TH145069

Average Customer Rating:  5.0 out of 5 stars   (2 Customer Reviews)

These custom clips and pads let you mount Thule Evo Clamp feet on your vehicle with a naked roof. The rubber-coated steel clips are easy to install - just slide them into the feet until they click. Rubber pads help protect your roof from scratches.

- TH145069

Very well made. Mounts properly on my 2018 Hyundai Elantra. Very complicated extrusion making the rack very versatile and strong. Instructions not very good. It took me a while to figure out how to slide the bars onto the roof mounts. I never found anything to show me that.

- TH145069

Order arrived promptly and correctly, staff provided excellent service and were very knowledgeable.


Ask the Experts about this Thule Roof Rack

  • Can Roof Rack Fit Kit Rubber Pads Be Replaced?
    Mounting a roof rack onto a car with a naked roof usually requires three component groups: the fit kit with uniquely shaped rubber pads and hooks, the towers, and the crossbars. In this case, the rubber pads of the fit kit on your car needs replacing. Manufacturers don't sell the individual rubber pads for each fit kit because of the sheer amount of work that goes into making sure each pad and hook fits each specific vehicle and to keeping them in inventory. Also, if one of your rubber...
    view full answer...
  • Thule and Rhino Rack Roof Rack that Fits 2020 Hyundai Elantra
    Yes both the roof racks you mentioned do fit your 2020 Hyundai Elantra: Thule part numbers # TH711420, # TH710501, and # TH145069 Rhino Rack # RRVA118B-2, # RRRLKVA, and # DK461
    view full answer...
  • Solution For Hauling 2 Bikes On The Roof Of A 2019 Hyundai Elantra
    For a roof rack I recommend the Thule Wing Bar Evo 135 Aluminum Cross Bars - 53" Long # TH711400 with Feet # TH710501. For the GT you will also need Fit Kit # TH145112, and for the sedan you will need Fit Kit # TH145069. For a bike rack you can use SportRack Upshift Roof Bike Rack - Frame Mount - Clamp On - Steel # SR4883. You can add two of these bike racks in order to haul both bikes on the roof. This bike rack will simply clamp onto the Thule Wing Bar Evo crossbars and has a weight...
    view full answer...

Do you have a question about this Roof Rack?

  • Why etrailer.com?

    At etrailer.com we guarantee:
  • Highest quality roof rack for the best price.

    Our Lowest Price Pledge ensures you will never overpay for the parts you need.
  • Real product know-how.

    We make sure that the products we sell are what we say they are, and that they work the way they are supposed to work. Get real advice from a real person who has the knowledge and expertise needed to solve your problem.
  • Most detailed, accurate roof rack information available.

    Because we take providing accurate product information seriously, we take our own detailed product photos, demo videos and installation videos, as well as verify measurements, instructions, and vehicle fit information.
  • Installations, made easy.

    We love helping people and have the most highly-trained customer service, hands-on experience, step by step videos and installation instructions.
  • Fast shipping.

    Your order is automatically routed to get out of our warehouse and to your door as quickly as possible. Receive free shipping on orders over $99.
  • Personalized service for life.

    We provide one-on-one, personalized service from the ordering process through the life of your product.
  • Trusted since 1946.

    We've been serving customers since our parts store first opened in 1946 and continue to be recognized by our customers, our vendors and third parties for exceptional service.
  • Returns Policy

    Need to return an item? No problem. Please read our Returns Policy for more information.

Info for this part was:

Employee Tyler C
Edited by:
Tyler C
Employee Colin H
Test Fit:
Colin H
Employee Dustin K
Video Edited:
Dustin K
Employee Randy B
Installed by:
Randy B
Employee Matthew S
Written by:
Matthew S
Employee Zach D
Video by:
Zach D
Employee Jacob H
Video by:
Jacob H

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.