Designed for pump houses, backflow enclosures, and critical areas, this industrial heater protects spaces from winter temps using an automatic thermostat. And the bracket keeps the heater secure with a bolt-on design that's made to stay put.
Frozen valves, cracked pumps, and stalled compressors can shut down a system and cost you a fortune. This heater was built to prevent that. With 1,000 watts of output, it has the strength to keep large enclosures and pump houses above freezing, while the forced-air design pushes heat into the corners where cold likes to linger.
Permanent Bracket Holds It in PlaceThis kit comes with a permanent mounting bracket for installations where the heater needs to stay put. The anodized aluminum resists corrosion, so it can stay installed year after year without worry. Once mounted, it stays put with a four-point bolt-on design that keeps it secure. Plus, the heater itself comes with a 6' marine-rated cord with a standard plug attached, so you've got some length to place it where you need (and you don't need to hardwire anything).Your work doesn't stop for cold snaps, and you don't have time to stand around monitoring gauges. That's why the thermostat is set to switch on at 50ºF and shut down at 65ºF. It holds equipment at a safe range that stops freeze damage without wasting energy trying to make compartments warmer than they need to be. And if conditions push the heater harder than expected, the heating element self-regulates to prevent overheating and ensures the unit continues running safely.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi, everybody, Andy here with etrailer.com. Let's take a real quick look at this Xtreme Heaters extra large industrial heater with mounting bracket. Now, this 1,000 watt Xtreme Heater is going to do a great job of protecting your large RVs and trailers from freeze damage by maintaining a safe temperature in industrial enclosures and compartments. This heater is going to be great for enclosures, protecting valves, electronics, compressors, and fluid systems, and this is gonna be ideal for trucks, trailers, well and pump houses, pest control vehicles and under skirted RVs. Now this mounting bracket can have a, a horizontal, vertical, or even upside down orientation, so that's going to, this is gonna give you a secure permanent mounting with the included hardware. So the heater's just going to mount on the, on the bracket, just like that, and then you'll install the hardware.
But, yeah, you'll be able to mount this on the side, even upside down, and that bracket will hold this securely in place, so a secure permanent mounting point here for your heater. This is constructed similar to our heater here, I think anodized aluminum, so it's going to hold up really well for you and it really doesn't even flex much when I put pressure to it. The overall length of this is gonna be about 12 and three quarters inches long and about five inches wide. Now going back to the heater here, this heater employs true forced air technology. Pushing warmth evenly through confined spaces for that consistent temperature control.
Its automatic thermostat kicks in at a 50 degrees Fahrenheit and then it's going to power down at 65 degrees Fahrenheit, keeping your heater safely above the freezing line without wasting energy. The self-regulating design means that it can't overheat, so it's gonna offer a fail safe shield for equipment in well houses, pest control rigs, or pressure washing trailers parked under a winter sky. Installation's gonna be pretty easy with this pre-wired six foot long wet rated cord and a standard three-pronged plug, so this is built to withstand damped punishing environments. It's gonna be compact yet strong, its anodized shell, inside and out, it's gonna resist corrosion. So this should give you years of service in outdoor electrical panels or laboratory corners where precision matters.
Whether you're safeguarding a air compressor from cold induced hiccups or ensuring that water flows freely in a pump house, this unit is going to give you heat fast, it's gonna shut off early, and optimize efficiency. So looking at the measurement of our heater itself, the overall length is about eight inches, if you include the mounting feet, about nine and 1/8th inches. The overall height is gonna be about five and 1/8th inches tall, then the overall depth or width is about three and a half inches wide. So, again, this includes everything that you see here. Now, if you would like the heater but you don't necessarily need that mounting bracket, we do have you covered.
If you just want the heater without that bracket, just use that model number that you see there instead, that you see on your screen, pop that in the search field of our website, that will take you to the heater without the bracket and you can add that to your order instead. Now, if you happen to have any other additional questions, don't hesitate to reach back out to us, we here at etrailer.com, ultimately, wanna be sure that you're getting exactly what you want and need. Well, that's gonna wrap up our look today, I do hope that it was helpful for you. Again, my name is Andy. Thank you for joining me.
Ratings & Reviews
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.