To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
These front tie-downs mount directly to your truck’s frame, the most solid part of the vehicle. That means the camper’s weight is evenly distributed and its center of gravity stays low for better handling and less sway. The setup keeps everything stable on long hauls or rough roads so your ride feels smooth and controlled.
Each tie-down bolts to existing holes in the frame, so there’s little to no drilling required. The fit is custom, which means the tie-downs hug the frame tight with minimal loss of ground clearance. That clean install keeps your truck strong and looking right without extra cutting or fabrication work.
When you’re not hauling your camper, pull out the removable arms and you’ll hardly notice the brackets underneath. They sit tucked close to the frame and are mostly hidden from view, keeping your truck’s lines neat and uncluttered even when the tie-downs stay installed.

Made from black powder-coated steel, these tie-downs are built to resist corrosion and stay strong through rough weather and years of travel. The heavy-duty finish keeps rust at bay while holding up to dirt, salt, and road wear so you can count on them trip after trip.
Each arm has two pin holes so you can extend it just far enough for a clear tie-down angle to your camper’s anchors. Two holes in the attachment plate give you flexibility to set the best pull direction for stable tension. Once tightened with turnbuckles (sold separately), your camper stays locked in place without shifting or sliding.


Ratings & Reviews

Mark
6/6/2025
These tie downs are sill working as advertised. I have travelled over 20,000 mi with them in various conditions with about 10 of that time in dirt roads or 4wd roads. Nothing too crazy, but with my camper and these tied downs I am confident that the camper will remain attached and be secure. It hardly moves around at all. They are worth the money and I can still remember how easily they installedvery welll thought out design and installation!


Heather A.
5/1/2026
Hi Jim! I can see why that would be frustrating for sure. The good news is you usually don’t have to do anything drasticmost fixes come down to slightly repositioning the exhaust system rather than fully relocating it. That can mean loosening and adjusting a bolt-on hanger, adding a small spacer, or even tweaking the hanger position just enough to create some clearance. I’ll drop this article here since it walks through a few simple ways to fix it step-by-step, but overall you’re on the right track it’s typically just a matter of giving the exhaust a little more room so nothing is rubbing or under tension. This help article is about a hitch install but it still applies here.
Helpful Links

Jenny N.
12/5/2022
I reached out to the manufacturer. They advised that they think it is a combination of the Northern light camper anchor point location being situated so far back on the camper and possibly the front of the camper not being all the way against the bulkhead of the bed if it is moving forward still. Otherwise, everything looks typical of a truck camper and truck installation. If it has any room to slide forward, it will in a sudden braking situation.

Albert
12/6/2022
Jenny thanks for your reply and diligence in reaching out to TorkFit. The NL camper does have forward bumpers for abutting the bulkhead. However when bulkhead contact is made the body of the my 21 Silverado makes contact with the fiberglass body of the camper. The pressure from a recent ‘sudden stop’ and ‘slide forward’ created enough pressure to chip paint on the truck. The bumpers make contact with the bulkhead about 10”-12” above the bed-bulkhead connection. The 90* corner at bottom, this should be the strongest area. I will install stop chocks at future loadings. I’ll also attempt to possibly install the TorkFits in a more vertical position. Thanks.

Lazer S.
12/30/2025
Glad to hear you are liking them, Milton! And I agree, the TorkLift tie downs are superior to the HappiJac tie downs. They are just more secure and heavier duty. At least in my opinion. And that sounds like quite the trip! Was it just a camping trip or did you do some fishing and or hunting?

Charles F.
5/24/2021
A year later and I couldnt be happier! I stand with my previous review 100

Dot
7/16/2023
A year later, I just got back from camping trip. I love the easy set up of these hitches. I’m a 65 year old woman, and I can put these mounts on my truck in less than five minutes. Then, another 10 or 15 to put the chains and turn buckles on, make them tight. I usually drive about 5 miles maybe 10, go get gas, and give all the chains a shake to make sure they’re still tight. If not, spin the turnbuckles a time or Two. And off, I go. I am extremely happy with this investment. Of all the things I bought after buying the camper, this has brought me the most security and feeling of safety. Good luck, happy camping whatever you decide.

Reed
4/12/2024
This is a very superior product. It was easy to install and is very functional and looks great. I highly recommend this product. Very well made and designed.


Scott
12/1/2025
It was an easy install, and they have worked with out flaw. I would recommend torque lift products to anyone installing a pick up camper. 2018 F 250 short bed crew cab.
Do you have a question about this Truck Camper Tie Down?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.








Mike L.
10/29/2026
Thanks John, we sure appreciate that! I'm glad to hear your tie-downs are working well for you...