To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
When you’re driving long distances with a camper, stability is everything. These TorkLift tie-downs mount directly to your truck’s frame—the strongest part of the vehicle—to keep your camper secure and balanced. By distributing the camper’s weight evenly and lowering its center of gravity, they prevent sway from crosswinds and rough roads. The result is a setup that tracks straight and feels steady behind the wheel, even with a heavy load.
You don’t have to sacrifice your truck’s appearance when the camper’s off. The tie-down brackets fit tight to the frame and sit nearly flush with the underside of the vehicle. When you remove the arms, the brackets are barely visible, keeping your truck looking clean and uncluttered between trips. It’s a simple way to keep your rig ready for adventure without changing its everyday look.
Mounting these tie-downs doesn’t require cutting into your truck or drilling new holes. They attach to pre-existing holes in the frame for a solid, custom fit with minimal effort. Because they’re tucked up close to the frame, ground clearance stays nearly the same, so you won’t be scraping or dragging when driving over uneven ground or backing up steep driveways.
Made of strong steel with a high-impact powder coat finish, these tie-downs are built to take road grime, weather, and heavy use in stride. The finish adds an extra layer of protection against chips and corrosion, giving you confidence they’ll hold up through years of hauling and storage.
Each arm has two pin holes so you can set how far it extends from your truck body. This lets you clear fenders or sidewalls while still keeping your turnbuckles at the correct angle for secure tension. With two anchor holes on each tie-down plate, you can fine-tune your setup so your camper stays tight and steady from every angle.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi, everybody. Andy here with etrailer.com. Let's take a look at these TorkLift Custom Frame Mounted Front Camper Tie Downs. Now as I mentioned, these are a custom fit specifically for your 2022 and newer Toyota Tundra with a six and a half foot bed and four wheel drive. This is for the double cab without board or step underneath your truck bed, and with a factory installed hitch. Now, on custom fit parts such as these tie downs, I do recommend taking advantage of our vehicle fit guide here at etrailer.com.
Input the year, make, and model of your vehicle, and our fit guide will confirm if these will work for you, or if we have something comparable that will work for you. Again, these are front camper tie downs, and to find the rear ones that will pair with these, again, use our fit guide to find those as well. Now, these tie downs are going to give you attachment points at the front of your Tundra's truck bed for securing a bed mounted camper. And the frame mounted design is going to ensure excellent handling, because securing your camper to the truck's base instead of its bed better distributes weight to keep your setup from being too top heavy. These brackets fit tight to your Tundra's frame, so there's not gonna be any loss of ground clearance.
And these steel tie down inserts are going to secure to these steel receiver brackets. And of course, these inserts are gonna give you those attachment points that you need for your turn buckles. Now, these inserts can be easily removed from the frame mounted brackets with the included pins that you see here. So let me go ahead and just give you a brief demonstration of that. So I went ahead and released and removed my pin here, and then you're gonna be able to easily slide out your insert, and then you can take these inserts and maybe even put them in the rear of the cab of your Tundra.
And then when you're ready to use them, just take them out and slide them into your receiver bracket. I did wanna point out that we have two different holes on our inserts, and the first hole here, it can be used if your camper is a little bit wider. Just use that first hole on this insert to have the tie down point stick out a little bit farther. And then if your camper is a little bit narrower, you can move it into this second hole on the insert. So these will fit on my table here and not overhang.
I'm gonna slide these into the second hole there, and then replace my pin and secure it. And it's as easy as that. Now, both the inserts and the brackets and the accompanying brackets have a high impact powder coat finish that's going to give you an extra layer of protection. And you're gonna receive everything that you see here on the table before me. Two front tie down inserts, the frame, brackets, and the necessary hardware that I have here in this bag, along with instructions to guide you through the installation process on your Tundra. These are made here in the USA, and they also have a lifetime warranty from TorkLift. Well, that's gonna wrap up our look today. I do hope that it was helpful for you. Again, my name is Andy. Thank you for joining me.
Ratings & Reviews
Lazer S.
9/16/2025
It definitely is safe the way you have them, Paul! In a perfect world, the turn buckles would be perfect vertical, but this an imperfect world and not all campers have the attachment points in the same place. If you take a look at some of the installed pictures on the TorkLift Locking FastGun Turnbuckles # TLS9529-2-LK page, you can see most of them are at an angle. It's perfectly normal. Are you running any suspension enhancement on your Silverado?
Paul
9/27/2026
These tie downs are great, so easy to use. Camper never budged a hair
Andrew N.
9/27/2026
Kate F.
8/10/2026
Thanks for the pictures Rich. We will be reaching out =)
Bob
11/1/2025
I have not had any issues at all with the tie downs.
Heather A.
4/10/2026
Looks great! What kind of camper do you have?
Lazer S.
10/14/2025
Install looks great, Megan! Especially for it only taking two hours! They were moving. : ) Happy we confirmed what you found as well. Tie downs can be a pain in the rear with all the options out there. Now I do have to ask though, have you guys thought about any kind of suspension enhancement for the rear axle? It's a little hard to tell, but it looks like the back is sagging a bit in your last picture.
Lazer S.
10/14/2025
Clay
7/31/2026
A year later and I would not do anything different. Absolutely the best system available especially paired with the fast guns. The camper is solid mounted and does not move. Yet can still be off loaded in just a few minutes. Remember good stuff isn’t cheap and cheap stuff isn’t good.
Christopher H.
7/31/2026
Kate F.
6/5/2026
Great set-up Viviana!! Glad to see you went with the best =) Where did you go for your first trip?
Nick S.
1/12/2026
I love these TorkLift tie downs, and it is great to hear you are liking the quality as well. What kind of truck camper are you going to be running with these?
Kate F.
8/20/2026
We appreciate the kind words Charles! Where did you take the in-bed camper for the first trip?
Gwendolyn Y.
9/18/2025
Install looks great, Dale! Where're you headed off to now?
Gwendolyn Y.
10/1/2025
Do you have a question about this Truck Camper Tie Down?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Straw
8/24/2026
A year later, no issues with tie downs, except normal wear and tear and metal to metal wearrust progression. These tiedowns are designed great and fit function was clearly created by someone who knows not only design but install ! E-trailer is “the” place to buy rv, camper, towing etc products - the install videos are sooooo helpful ! Thx ET !