# 1
Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
My order was missing installation parts, but the etrailer team were quick to correct the issue. Even without a lift, I was able to install the receiver and brake light cable quickly, thanks to their extensive video libray.
2024 CRV. Pretty straightforward install. The fish wires in the kit are a fantastic solution to holding the bolts. Thanks!
# 2
Curt Multi-Ball Adjustable Ball Mount for 2" Trailer Hitches
Picked up my teardrop in ABQ on 2/17/23, and the Curt ball mount lined up perfectly with no drop/rise, and the extra length gave clearance for my rear door mounted spare tire. This mount is a beast, and the "overbuilt" nature of it gave me confidence that my Bronco would tow the teardrop easily. I also got the Curt Echo wireless brake controller, which synced easily to my phone and was easy to install, set up, and use. Overall a great towing experience, thanks to etrailer and Curt!
Works great used for 3 different trailer we have handy it's heavy well made.
# 3
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Sara R was helpful helping me find the right hitch for what I described as needing. I was excited to see the hitch pin in my order details even though I didn't order it. Sadly, the picture gave me a false impression. Overall, excellent customer service and product.
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
# 4
Rapid Hitch Adjustable, Aluminum Ball Mount Kit w/ 2 Greaseless Balls - 4" Drop or Rise
Great fit and finish looking forward to the first tow with it.
Good hitch so far towing multiple days a week for work . Wish the aluminum balls didn’t oxidize up so quick , doesn’t keep it nice look for long .
# 5
Convert-A-Ball Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 10,000 lbs
Good, very solid ball mount with just the extra rise I needed, 2 3/4", to get level trailer and good clearance for the trailer jack. But excessive shipping charges from etrailer, $[XX] for an $[XX] purchase. Found out to my cost later that [online vendor] would have shipped for free.
As a full-time RVer, e-shopping is very important for us. etrailer was the right place to shop. Right product, delivered on-time for a great price. You beat the local discount RV store by $25 including shipping. At the same time, I had another outfit send me a clearly inferior product to the one they displayed. Said they would e-mail a pre-paid shipping label for the return (didn't) and tried to put the blame on Amazon. Thanks etrailer for a great experience !
# 6
Ball Mount Adjustable with Sway-Control Tab, 6,000 lbs
The ball mount did not fit onto the shank. This was a very disappointing experience.
The fit of the U channel for the ball mount was too tight over the verticle drilled box tube. It needed “persuasion” to get it over the tube. This will make height changes away from the shop difficult. No rattle though.
# 7
Rapid Hitch Adjustable Aluminum Ball Mount Kit - 2 Zinc Balls - 4" Drop or Rise
What do i like about this hitch…i tow trailers requiring both size balls andmits easy to flip this around and adjust tow height. Its lightweight and easy to take on and off when needed. The built in locks keep the hitch on my truck. I like it and recommend it.
I purchased this to replace a Fastway Flash E Series Ball mount that I purchased and returned from another online seller that did not provide enough clearance from my rear bumper in the rise position. My vehicle really needed the extra 5/8ths of an inch of length on the shank of the Rapid Hitch. Clearance was not a problem in the drop position; but with a receiver that's 18-inches off the ground, I need to use the rise position more frequently than many. The other thing I noticed is that this ball mount is feels more substantial than the one from Fastway. In use, I prefer this to the Andersen EZ hitch I had been borrowing. It looks really cool. It has 5 adjustment positions rather than four and bit more adjustability in either direction. Plus, it still fits in easily in the storage area underneath the floor of my SUV. And did I say it looks really cool. I hated to put grease on the ball before I went to hook up the trailer. Also, I plan to get the lock set. It's looks great on my SUV and seems likely to disappear overnight and look great on someone else's vehicle.
# 8
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
Haven’t used it yet, but looks good. I’m not sure what height offset I need, so this kit gives me several options, plus two ball sizes. Really good value.
Ball mount kit arrived quickly (within a few days) upon placing order online. Parts were shipped loose in box and bottom flap on box was open when received. Fortunately, all the parts were still in box and in good condition. Kit includes ball mount hardware I need to pull trailers with different hitch heights.
What our customers are saying:
"I just wanted to thank you for the excellent service and outstanding product. I certainly will keep your web-site at hand if I need other parts. Thanks again Dick"