# 1
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
Haven’t used it yet, but looks good. I’m not sure what height offset I need, so this kit gives me several options, plus two ball sizes. Really good value.
I installed the draw tite hitch onto my brand new 2018 Subaru outback. I'm 68 years old, not as strong as I was, but proud to say I did the job all by myself in about 4 hours. Here are some tips you may find useful. Watch the video-it’s pretty good. I had difficulty getting the exhaust system down and worried about getting it up again from the moment I got it down...read on-help will follow. I bought a stepup drill bit which worked great for drilling the hole in the chasis. I clamped the hitch onto a floor jack, then rolled it and raised it into position. Used metal shears to easily cut out the heat shield as per the video. Your inclination will be the screw the fishing tool provided all the way up the carriage bolt. That won’t work; just screw it on to the tip of the bolt. I couln’t get the exhaust hangars in place even after lubricating them with wd-40. I dropped the rubber hangars into undiluted liquid car wash soap which made them much more slippery than the wd-40. After that the rubber hangars slipped into place pretty easily-that’s my best tip. Finding the electric connection plug for the wiring harness was almost as hard as installing the hitch. I was very happy with how the job came out. Good luck.
# 2
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Sara R was helpful helping me find the right hitch for what I described as needing. I was excited to see the hitch pin in my order details even though I didn't order it. Sadly, the picture gave me a false impression. Overall, excellent customer service and product.
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
# 3
Curt Class II Drawbar - 3-1/8" Rise - 11-1/4" Long - 3,500 lbs
Used on my 1999 Dodge Intrepid's CURT 12006 Class II 1.25 in. Receiver Hitch: 350lbsTW/3500 lbs GTW. I use this Curt Class II Drawbar - 3-7/8" Rise - 11-1/4" Long - 3,500 lbs to tow a 3,500+ GTW dual axle trailer. I have used it with the trailer FULLY loaded and it performs EXCELLENT. You have to make sure the trailer is loaded correctly so as not to put too much down force on the tongue/drawbar. I was skeptical that the SOLID 1.25" bar would not take the load, but it is super strong. I chuck it in the trunk when not in use to protect passerby's shins, but it sticks out far enough clear the Intrepid's bumper, and is solid with a 2" ball (required a bushing). etrailer got it out fast at a good price! I would totally purchase this again from them.
Every part excellent quality. Perfect fit, all parts were exact for my vehicle. Watched the video on youtube for wiring and being a mechanic for over 50 years was able to connect signal lights all from driver side of harness. Instead of leaving plug inside trunk I wired through the rubber outlet to the back of the hitch ready for use. Very happy highly recommend etrailer.
# 4
Curt Multi-Ball Adjustable Ball Mount for 2" Trailer Hitches
Picked up my teardrop in ABQ on 2/17/23, and the Curt ball mount lined up perfectly with no drop/rise, and the extra length gave clearance for my rear door mounted spare tire. This mount is a beast, and the "overbuilt" nature of it gave me confidence that my Bronco would tow the teardrop easily. I also got the Curt Echo wireless brake controller, which synced easily to my phone and was easy to install, set up, and use. Overall a great towing experience, thanks to etrailer and Curt!
Works great used for 3 different trailer we have handy it's heavy well made.
# 5
Curt Class III Ball Mount with 2-5/16" Ball - 2" Rise or 4" Drop - 7,500 lbs
This was purchased for towing a 7k GTWR utility/landscape trailer with my 2018 Chevy Silverado 1500 WT 4x4. I measured for necessary drop before ordering, and the 4" drop is darn near perfect. It's a great help that the 2-5/16" ball comes complete, installed and torqued properly at the factory. Appears to be quality construction, fits and functions perfectly. I have no complaints or issues.
The Curt Class III ball mount arrived as promised and the product is as advertised. My whole experience with the process was top notch from ordering to delivery, installation, and use all 5 star.
# 6
Curt Fusion Ball Mount for 2" Hitches - 2" Ball - 4" Drop - 7,500 lbs
All of the products I've have bought for my trailer project from etrailer have been great. My go-to place for anything trailer related!
This was the right set up for my 2018 4Runner. Works great. As a footnote, I now have a second vehicle for towing (2019 Tundra 4X4). Using the measuring process provided by etrailer folks, I found the same ball works great on the Tundra. Thanks!
# 7
Curt Class III Ball Mount with 1-7/8" Ball - 4" Drop - 3,500 lbs
The Curt trailer hitch and wiring harness for my 2016 Highlander was a perfect fit. Installation was a breeze just following the etrailer videos. I opted for the 4" drop ball mount because of the Highlanders ground clearance but the standard 2" drop would have been just fine. Will use etrailer again without hesitation.
I purchased this hitch to pull my utility trailer with. It was easy to order, arrived on time, and simple to install/use. This hitch is built very well and strong, and has a good coating finish on it. Great product!
What our customers are saying:
"Another great purchase. Low prices, fast shipping and great customer service are always provided."