Most Popular Trailer Connectors for Ford C-Max

Used on tow vehicle for hooking up wiring harness to motorhome

This part is an exact replacement to the part that failed. The failure was caused by a poor installation which allowed the rubber boot to chaff on the truck frame. As it was an exact replacement installation was straight forward although I modified the mounting bracket to prevent a reoccurrence of the problem.

Çable good but after putting new 7way plug on truck cable wire colors did not match etrailers picture

7 pin connector separated from cable. I was expecting that "Molded Cable" meant that the connector was fused to the cable insulation but instead, the two separated almost immediately after I installed it. It still works fine as the wires are connected securely inside the connector but with the outer covering pulled out like this, I don't think it will last very long.

Click to Enlarge

Installed the Hopkins muti-tow 7, 5, and 4 way flat connector this morning. I ripped the original connector that was attached to the bottom of the hitch receiver off when I was 4-wheeling into the Doll House campgrounds in the Maze District of Canyonlands a month ago. So, I cut a hole in the bumper and mounted the new Hopkins connector, cut off the old broken connector mounting bracket, and connected the factory wiring to the new Hopkins device. Hopkins product installed easily, looks great, is now out of the way, and has the flexibility of multiple trailer connectors when required. I am pleased with the product. Attached is a photo.

Click to Enlarge

Exactly what we had been looking for. Now I can hook up multiple trailers with different connectors and all the electrics on each trailer works. I mounted mine directly to the receiver hitch frame. The biggest challenge for us was routing the backup wire from the taillight housing, through the body of the truck to the connector. the rest went together fairly easily. Seems to be pretty solid and looks much better than the loose pigtail connector it replaced.

Click to Enlarge

Click to Enlarge

Excellent Quick Delivery When you are driving a Test or NASCAR Hauler you need replacement parts very quick, just like a pit stop. Thank You very much for the rapid delivery. Mint Moore III Ford Performance Race Hauler Driver

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

A great little heavy duty plug that I use to connect my car to the rv when towing 4 down.

This is a piece of junk….one of the male plugs was broken and I checked the current on the others and no current passed through from one side of the plug to the other. Complete Junk….do not buy this product. I ended up going to [store] and getting a curt plug that worked just fine.

I explained to Roger (I believe was his name) that I have a Blue Ox tow bar and base plate, The base plate was installed along with the wiring kit, but did not include the wire to go from the front of the grill to the interior of my Jeep to plug in my RVi brake, and this is what he sent me. I'm attaching a picture of what I have on my vehicle. Not only was it the completely wrong part, but it arrived in damaged packaging which I did not open. Please send return instructions.

Click to Enlarge

I've got that trailer that has had one tough life. Yep, hundreds of gigs, PA and sound equipment rolling in and out, the heat, the cold, the sun, rain, and snow. Chicks, guitar players and drummers, you know, all the things that beat the hell out of a drum! Thank the music Gods for etrailer.com! The place to remedy the ills that trailers need in times of harsh environments, tough crowds, tin-ear'd musicians, and you ain't nothing but Hound Dogs!

I've never really liked Flat-4 type connectors. Unless you leave them dangling, they usually require that you crawl under the vehicle to connect them. (...Murphy's Law dictates that this will always be when it's raining or snowing). This Pollak 4-pole round socket, along with a Tow-Ready harness, and matching trailer connector, provides a neat, factory installed look, that's more convenient, and durable. My orders from etrailer arrived quickly, and with great seller communication. A+

Click to Enlarge

Quick shipping, will order from them again!

Exactly what I needed and It's a great fit

Love the flexibility of the cord in cold weather. But where the cord connects to the plug, that has seperated. Still working, but do not know how long it will last.

The bargman 7 way moulded trailer end is a high quality unit. I have been using it for a year now and it has performed flawlessly. The sturdy moulded plug ensures no moisture can get inside. Both the insulation of the individual wires and also the outer sheath are made of silicone and remain flexible even at canadian winter temperatures. There is just one way I think the unit could be improved. The outer blue silicone coating is thin, and not very abrasion resistant. If it contacts the grouns at all, it will quickly wear through. Just a little thicker sheath would be nice. Overall I am very happy with my purchase, and would certainly purchase again

Click to Enlarge

I rewired my boat trailer using the wesbar 4-flat connector from junction box to the hitch. I do wish the wesbar connector was available in tinned wire. I used tinned 14 ga tinned wire for the rest of the wire and ran a ground wire to every light eliminating the trailer frame as a ground. Also added a switch at junction box for a manual trailer reverse flood lights. Filled the junction box with removable potting Gel to prevent water/corrosion. Works great. No issues. Never been stuck on the side of the road troubleshooting an electrical issue / bad ground. Would purchase this again, unless I could find a marine/tinned wire version, then I would purchase that one instead.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

We installed this cord on a tilt bed trailer that we use to transport scissor lifts. We have multiple trucks that pull this trailer and the receptacle on these trucks are in different locations. This required using a 4 flat extension on many of them and as you would expect, the extensions come up missing and of course no one knows what happened to them. We tried every trailer supply store in the Phoenix area and no one carries a cord like this. Because this one is 14' long, we can cut off what we don't need and wire it into the J-box on the trailer and make it long enough that we don't need an extension. Great product.

I have used etrailer probably four or five times now and have been very happy. Shipping is fast, prices are reasonable and the products are of good quality. I purchased more of the Quick Fix 4 Pole Trailer Ends - they work really well for the non-automotive industrial control project I am working on.

Click to Enlarge

They have just what I needed and it arrived very quickly.

Used on a pull behind motorcycle trailer so could go from receiving a 6 pin to a 5 pin. Wired it into loom so can use on more than one motorcycle. Works great. Glad to have found a place that even sold this product.

A similar trailer light connector was installed on my motorcycle cargo trailer when I purchased it way back in 2003. When I purchased my new Gold Wing in 2019, I wanted to use the same type of connector. Since I had to add a new female connector to the bike, I decided to renew the male connector on the trailer. I especially like this connector because it always stays secure when connected. I also wanted the connections to be out of sight when not in use. I have pulled my trailer with this new connection for over 2,500 miles and it has performed great.

Click to Enlarge

This is the perfect solution for the Harley Davidson 5 wire harness, easily lets you convert to 4 pin and stores away when you don't need it.

The product did not work and I have to order another that will work.

The pins were too big by a little bit. Had to force the female plug into the socket

Nice product. Proper di-cast with chrome finish...not the cheapy plastic one this replaced. I prefer this to the flat-4 plug, because the flat-4 can't really be secured the the vehicle, and most of the time thay are run out the truck over the bumper. I didn't want to risk scuffing the painted bumper cover, plus I have a 3rd brake light on my trailer, which requires a dedicated brake light wire. I installed this on a 2006 WRX and a 1990 Mustang (1 trailer, 2 cars that tow it)

Click to Enlarge

etrailer videos make things so easy! Thank you!

Worked fine.

Used this as the connection point for the Roadmaster diode wiring kit. Seems to be well made and will hopefully last a long time. I did spray paint it flat black so it blends into the front bumper of my “toad” a little better.

Click to Enlarge

Base plate and all hardware worked well and fit like a glove, instructions were easy to understand great product

I've got that trailer that has had one tough life. Yep, hundreds of gigs, PA and sound equipment rolling in and out, the heat, the cold, the sun, rain, and snow. Chicks, guitar players and drummers, you know, all the things that beat the hell out of a drum! Thank the music Gods for etrailer.com! The place to remedy the ills that trailers need in times of harsh environments, tough crowds, tin-ear'd musicians, and you ain't nothing but Hound Dogs!

Great place for any trailer needs. They alway gave what I want at a good price and fast shipping.