# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
It will do the job, for sure.
I recently purchased a class III Curt hitch, mount, ball, wiring harness and hitch pin for my 2011 Toyota Rav 4. The installation was as described, straight forward and easy. The instructions were easy read and matched the vehicle I have. Everything fit together exactly with no modification needed. Shipping was directly to my door. The unit was undamaged and everything was shipped all in the same box. I have used my hitch several times, and although I an new to towing, I look forward to years of use. I did have to make a quiet clamp for the banging mount with an empty trainer, but from what I understand, this is common to all hitched.
# 2
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 6-3/4" Long - 3,500 lbs
It's a receiver hitch! It's well built, the welds are clean and it fits the trailer hitch. Not much else to say!
# 3
Draw-Tite Drawbar for 1-1/4" Hitches - 5/8" Rise, 1-1/4" Drop - 7" Long - 3.5K
Finished nicely and fit perfectly, except had to take a file to the inside of the receiver as the punched holes deformed the tube slightly. Now...smooth!
good product, good quality. on time delivery
# 4
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
I have a 2004 RAV 4 and I was trying to get my ball away from the spare tire carrier. I think I probably would have been fine with the next size (shorter) ball mount and still got the job done. The good news is that with the 2 inch drop, I can open the rear door and it just rubs the seal at the bottom of the door a little bit, but I can still easily open the door. I did not want to drop the ball any lower, So this works out well for my rig.
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
# 5
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 6
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
Superb quality product that solved my RAV4 rear hatch to trailer winch post problem with it's extra long length!! Super fast shipping!! Can't get any better than etrailer!! Thanks!!
2007 Toyota Rav4 owner. I needed this to reach out beyond my spare tire, works perfectly and no clanging or unnecessary movement.
# 7
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 9-3/4" Long - 3,500 lbs
The 5 inch rise on this hitch ball mount was perfect for my 07 Toyota Rav4. The rear door opens to the side on this year Rav4 and it has plenty of clearance. I tow a 16 ft aluminium boat and this 5 inch rise ball mount works perfectly on the Rav.
# 8
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
Everything came as described, and I am so happy with the products and service! etrailer.com is my definite go to!!!
Makes for a great hard-core dirt road set up with a 3000 pound trailer, in conjunction with the Curt rocker ball, Towing with an F150 over many miles of washboards, down through washes where the road was washed out, etc. Really makes for a gentler set up on the equipment in the trailer and the truck. Thanks a lot E-trailer!
# 9
Draw Tite Drawbar for 1-1/4" Hitch - 5/8" Rise, 1-1/4" Drop - 9-3/4" Long - 3.5K
Excellent hitch receiver. Perfect fit, nice welds, easy install.
Worked as expected
What our customers are saying:
"Thank you! I enjoyed shopping your site."