Best 2021 Ford Edge Tow Bar Braking Systems

Thanks to installation videos provided by etrailer, I felt confident that I could do the install myself. I had never pulled off moldings and panels in a car before, but with your videos as guidance , it was a breeze. This system was going into a 2016 Ford Edge 3.5L AWD and your (and SMI's) instructions call for installation of 2 check valves. After calling SMI to clarify the install points, it got even easier, as only one valve is required, and is ridiculously simple to install it. No cutting of original car hoses required (see photo). After everything was installed, the whole setup just simply worked, no troubleshooting required. That was fun and it is totally doable, even for the average guy like myself.

Click to Enlarge

Click to Enlarge

Click to Enlarge

One year and oner12k miles the DemcoStay-In-Play has worked flawlessly in our 2020 Ford Edge ST. This includes a trip to Colorado and PA. Highly recommend and etrailer is great to do business with.

Installed in 2016 Ford Edge Titanium. Instruction were easy to follow. If installed in the back of the vehicle wire is not long enough. Had to add an additional 4 ft of cable. Cable with the kit is long enough only if mounting towards front of the vehicle or under driver's seat. Mine did not fit under the seat so I had to put it in cargo area rendering the cable too short, had to add 4 ft of cable. Would have given 5 stars if it wasn't for the cable length issue.

The braking system and the lights are working, one year after I bought them. However, I am towing a 2016 Keep Patriot, and about 2_500 miles after install, the system started making an annoying clicking noise when I enter the Patriot, which stops after about 10 seconds and then starts up again, usually a minute or so later, for another 10 or 15 seconds. etrailer first said that they had never heard of.such a thing, then said that there are otherwise comments for Keep Patriot owners on forums. Still have no.fix. Also, at first I did not know that to store the tow bar, it must be pulled up so that the post fitting can moe to the position where it fits into the hole.in the smaii yellow bracket, which works well when used correctly. And store the coiled.wide in your tower vehicle.to prevent corrosion which will interfere with its function.

Relay works as advertised - cuts power to my 2013 Edge brake lights (with the key in the off/or accessory position) preventing the Edge brake lights from overriding the coach brake/turn signals when my supplemental braking system pulls the Edge brake pedal down. Bit of a chore to install, mainly due to close quarters under driver's side of lower instrument panel and forced to lay half way in/out of Edge over the door sill. Also, vehicle info on Roadmaster web site indicates the Edge brake light wire coming from switch is purple/white, but I found 2 purple and white wires on mine, both together in the same socket on the brake light switch. Guess it depends on one's color sensing, but one of mine was a lighter shade of purple and the other darker, more shiny. I spliced into the light purple one first and naturally it was the wrong one, so had to reconnect it and splice into the other one to make everything work. Not a biggie, but the mini fuse tap supplied in the kit will not work with the low-profile mini-fuses used in the Edge interior fuse panel - you have to use a regular mini-fuse. FYI - 2013 Edge Limited, V6/FWD; Air Force One supplemental brake system; DEMCO RV Tow Harness wiring kit (9523100) for tail/brake light connections (plug in/no splicing); DEMCO baseplate and Blue Ox Towbar.

Good quality items. Easy instructions. Only difficulty is crawling under the dash. If you have even done that, you know what I mean. I

The product shipped on time and has been worry free. etrailer gets 5 stars for customer service every time I order from them.

This braking system does what it's suppose to do, smooth proportional braking between motorhome air brakes and the tow vehicle. The only reason I did not rate at 5 stars is that there is a slight misalignment of air cylinder mounting bracket and 2022 Jeep Gladiator brake pedal.

Installed in 2016 Ford Edge Titanium. Had to buy additional cable connectors that were not included in the kit and instructions did not specify they were required. I would have given 5 stars if it was at least mentioned in the instructions.

This is a great device. The reason I bough it from ETrailer is because of customer service. They are super helpful. Place the brake as suggested and try it out. Works just as expected.

So I never used mine. This is for those trying to decide if they need one. I tow an F250 with a 43’ tag axle, with an 8.9l Cummings. Yes I can feel the truck back there but I have never had the need for additional braking. Crossing the Snoqualmie pass on I-90 or driving through the cascades, I have no problems slowing with the engine brake. I have a big rig and tow a big truck so if this is your set up I’d give it a shot before committing to such an expensive item that I never use. I’m sure smaller rigs pulling larger trucks will benefit from a device like this.

Ordering was easy. Delivered very promptly. Actually cheaper then what the manufacturer sells it for. Live near manufacturer and having them install all my flat towing components this month. Great service Etrailer!!

It took me awhile to figure out how to set it up in my "Tiny Jeep" (TJ). I finally tried flipping the bracket for the brake pedal upside down, and that moved the connecting bracket forward just enough to where the shaft fit in the bracket. Used it once, about a month ago, and couldn't even tell the Jeep was connected to the motorhome. The tow vehicle is a 2023 Tiffin Wayfarer. The tow is a 2003 Jeep Wrangler TJ.

Had a problem with the connection to the unit but called etrailer and they sent me a new one after sending the other back to them. The hole process very painless and the the staff at etrailer was great to work with. Thank you etrailer for your great response.

I wouldn't use anything else! Once this system is installed it's literally plug-and-play. Nothing to move or install into the car, each time you tow. Just plug it into the coach's air break system and you're done. Install video from etrailer made it even easier to complete. You do need a bit of mechanical guidance/assistance as you're connecting to both your vehicles and coaches breaking system but it has worked flawlessly for over 11,000 miles and in some pretty intense traffic.

Click to Enlarge

Click to Enlarge

Easy install video was great in making decision shipping was on time communication excellent

I am a proficient DIYer (and was an auto mechanic many years ago). The installation took a lot of time - perhaps 8-10 hours for the brake controller. The most special tool needed was a rotary cutter (e.g., a Dremel tool). A cordless impact driver was also very helpful, especially with the self tapping screws. Getting the pully in the perfect position under the brake pedal took some trial-and-error to get perfect. Also, the included bolts for the brake pedal bracket where too short to accommodate the width of the brake lever - easily remedied with slightly longer standard bolts. Be very mindful of what is on the other side of the sheet metal you are planning to drill into. The brake supplemental vacuum system was a bit of a challenge, as the instructions are very vague regarding how to mount, and the space I had to work with was surprisingly tight. I ended up creating a mount on the inside front fender, and bolting the pump to that. Also, tapping into the vacuum lines took a couple of tries to get a leak-free connection. Think ahead about this, and be prepared to get a few small parts like hose clamps or right-angle hose connectors. This would be a potential consideration for any vacuum boost added on any vacuum power-assist application with any controller. I mounted the Brakebuddy main unit under the rear seat - that was a perfect location, and much better than the often suggested location under the driver's seat. I was very pleased with the installation result. I paired this with a Nighthawk tow bar. Be warned that the tow bar's included cable will not be compatible with the Stealth, as the Brakebuddy uses a proprietary connection at the towed vehicle. The upside of this proprietary connector is that all connections are build in, including the brake away cable and the battery charging line. (I modified the Nighthawk by replacing the included cable with a 4-pin cable to power the lighting system on the bar. This is just for extra safety and cool looks - I could have just not used the tow bar's included cable). With 1,200 miles of towing behind us, I can say I am very pleased with the performance. I rarely notice any difference in braking effort or effectiveness - which is a big advantage for a proportional system. My favorite feature is the ease and speed of connecting or disconnecting the towed vehicle. I'd give this a 4.5 stars out of five if I could, because I did need to add a few parts and make a couple trips to the hardware store to complete the installation. However, the excellent performance and ease of use once installed more than makes up for the inconvenience during initial installation. Special appreciation to the people at eTrailer, especially Nicole T, who provided support and guidance from pre-sales to installation. Also, I called Brakebuddy's support line with a concern, and they immediately picked up the line, addressed my question, and offered to immediately ship any parts if needed.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

I choose the Brake Buddy Stealth for my 2021 Jeep Wrangler because I wanted a “stay in place” brake system and felt it would be a clean looking installation. I finished the toad side of the installation today and thought I’d leave some notes on what turned out to be a bigger project than I’d anticipated. Again, this is my experience on the 2021 Jeep Wrangler 2-door. Your experience on other vehicles may vary. I started this install after installing a Demco Tabless Base Plate. Right out of the blocks, there’s really no convenient location to mount the cable connector to the Demco baseplate. I chose to mount it to under side of the bumper on the driver’s side. To provide clearance and a route for the wires, I had to cut a notch into the plastic air dam. I used one of the already screw screw holes and used self tapping screws in the other three locations. For added strength I epoxied the connector to the bumper as well. Since the bumper would be unremovable if the connector were hardwired, I added a waterproof connector. The kit is stingy with wire lengths, so I substituted my own wire. The Stealth unit itself i mounted beneath the driver’s seat. Don’t be fooled into believing there is clearance when testing with the driver’s seat positioned for rear seat access. Once the seat is returned to normal operation it lowers a bit and the box keeps the seat from being move forehand aft. I solved the problem by installing 5/8” thick nylon washers under the rear end of the seat slides. I also cut away a bit of the carpet under the front, inboard corner of the box. You will need to remove the driver’s seat in order to attach the front screws of the box. Be sure to disconnect and isolate the neutral battery terminals to prevent inadvertent air bag discharge. After removing the interior trim from the A-pillar, the door sill, and the driver side foot well, The wiring and cable tucked nicely away along with the OEM wiring and wiring for my taillights. I mounted the pulley horizontally behind the brake pedal. Installing the vacuum pump was my biggest worry and challenge. Instructions are to zip tie it “somewhere”. That seemed pretty casual for a safety system. I chose, instead, to fabricate an aluminum bracket that attaches to the lip of the engine compartment and to the wheel well (this latter attachment point is necessary to keep the pump from vibrating). Finally, the kit comes with 3/8” fittings to tap into the brake booster vacuum lines. The Jeep, however, uses 8mm nylon tubing. Brake Buddy, via etrailer.com, stated that the tubing would stretch and all would be good. Again, this felt casual for a safety system. Instead, I purchased an 8mm check valve and a 8-6-8mm barbed tee through Another online retailer to do the job right. I had to heat the Jeep tubing to fit even the 8mm tee, so the is no way the larger 3/8” fittings would have worked. See photo of my finished vacuum line installation. Bottom line, it was a POA install, but looks great. Hopefully it will stop the Jeep when towing. I’ll find out soon. :D

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Kit fits great! Hooked up a 2004 Workhorse to a 2002 Jeep Liberty. It might be preferable to be handy with some advanced mechanical skills and tools to install this efficiently. Directions are great but you do need to figure out your own locations for certain items like the break-away reservoir, compressor, routing lines and wires out of harms way, but not bad at all. Parts are great, everything there but added a couple different wiring splices of my own.

Click to Enlarge

Click to Enlarge

Your customer service leaves nothing lacking, and this follow-up from you is so out of character for the many web sites I have purchased from over the years. I am impressed by you and your company. I bought the tow bar and the brake system for my Equinox, and installed them my self (I am 70 years old) - and with your provided instructions and video, I had no problems (even though I was surprised by the number of parts and detail that went into the assemblies). Both systems have worked very well, with no problems. I am completely satisfied with them, and have told my friends and traveling acquaintances about your company. Thanks for your follow-up!

Thanks to installation videos provided by etrailer, I felt confident that I could do the install myself. I had never pulled off moldings and panels in a car before, but with your videos as guidance , it was a breeze. This system was going into a 2016 Ford Edge 3.5L AWD and your (and SMI's) instructions call for installation of 2 check valves. After calling SMI to clarify the install points, it got even easier, as only one valve is required, and is ridiculously simple to install it. No cutting of original car hoses required (see photo). After everything was installed, the whole setup just simply worked, no troubleshooting required. That was fun and it is totally doable, even for the average guy like myself.

Click to Enlarge

Click to Enlarge

Click to Enlarge

One year and oner12k miles the DemcoStay-In-Play has worked flawlessly in our 2020 Ford Edge ST. This includes a trip to Colorado and PA. Highly recommend and etrailer is great to do business with.

Overall a great system, there are some intricacies to the install as it pertains to old instructions with LED light in the TOAD vs. CoachLink Wireless and also the 3 wire reed switch vs. the newer 2 wire one. But using the provided written instructions along with YouTube videos you can figure it out. My other challenge was my Jeep is a 392 model and thus the battery and fuse box are in swapped locations, as well as a different VAC line layout, but again you can figure it out…just takes some time to study and trace the routing. My only real complaint was ordering, I was quoted the wrong system for my RV (Stay and Play) vs. AF1 since I DO have air brakes. etrailer was helpful in getting the return process but wants to charge me the shipping and possibly restock fee, I am working with them on this and hope to get a good resolution.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Works great fairly easy install. It has been in use for the last 8 month's with no issues. Here may be some helpful hints that I found when installing. Use 10-12" long extension for 13mm nut (left side of opening panel that was removed). Install bracket. Adjust plunger & backing nut by feel. Remove bracket. Install switch with ring washer & nut. Crimp red & green wires on switch wires. Reinstall bracket under dash.

Click to Enlarge

Click to Enlarge

This was a little tricky to get adjusted properly, but you just have to be patient until it's in the proper place. Had to adjust the mounting bar angle slightly to get it in the right place.

The product shipped on time and has been worry free. etrailer gets 5 stars for customer service every time I order from them.

Arrived on time. Installed it myself after watching some UTube videos. Fits abs functions great on 2014 Tiffin Red with 2017 Jeep Grand Cherokee

Best decision I ever made since purchasing my motorhome. Easy, convenient to connect and disconnect. Everyone I communicated with at etrailer was so knowledgeable and patient and friendly. If you are thinking of towing a vehicle behind your RV, do not purchase a towing package before you contact etrailer.

This product worked great for me. I didn't want the brake lights in my plug-in hybrid activating my trailer brakes when all I wanted was regenerative braking. Now I can get regen by taking my foot off the gas pedal and trailer braking by putting my foot on the brake pedal.

Delivered early and everything packaged as stated

The product shipped on time and has been worry free. etrailer gets 5 stars for customer service every time I order from them.

This braking system does what it's suppose to do, smooth proportional braking between motorhome air brakes and the tow vehicle. The only reason I did not rate at 5 stars is that there is a slight misalignment of air cylinder mounting bracket and 2022 Jeep Gladiator brake pedal.