# 1
20 Ft 4-Way Trailer Wiring Harness - Wishbone Style - 30" Ground
Just what I needed for my home-built bike carrier. My wife rides an e-tricycle and by the time I loaded the trike and a couple of bikes on this platform, you could not see the car's taillights or blinkers. This harness worked perfectly!
Wiring worked perfect for my project. I replaced the wiring on my 14 foot utility trailer. If I was to do it again I would buy the next length up. I would have liked to have a little extra wiring if I was to ever need it.
# 2
35 Ft 4-Way Trailer Wiring Harness - Wishbone Style - 42" Ground
on time as stated
Replaced the wiring and lights on my 1992 boat trailer. I was able to get everything needed from etrailer. I think Optronics is of the highest quality and recommend both etrailer and Optronics product.
# 3
Pollak Black Plastic, 7-Pole, RV-Style Trailer Connector - Trailer End
Sooo, bought another one to match my truck side connection as GM uses Pollak, which are known to not play well with other brands. The design is just a wire clamp to wire it, which I did with the first one, but trying to get it secured I stripped out the screw. There are no torque specs provided. I’ll move to crimped ring terminals on this one and dial back the torque a bit.
Used as a replacement for original connector that didn't have a positive fit. This one clicks in and provides confidence of a snug fit.
# 4
Great product no issues at all. Product as described & fit properly.
Pretty straight forward. I used it to switch my European trailer's connection to be able to connect to my Wrangler's 4-pin trailer hookup. No issues. works great.
# 5
7-Way Molded Trailer Wire Connector - 3' Long
I've had this in use for over a year and they don't build them like they use to. I use this on a gooseneck trailer and the piece of plastic behind the spade connector for the clearance lights and brakes has melted, allowing the spade connector to lose contact with the plug on the pickup. So the lights would cut off in the middle of the night and would have to wiggle the connection till I could fix it. I have an older Hopkins plug and never had this problem. To fix the problem I ended up putting pieces of thin copper wire behind the spade and have done it twice since the plastic melted a 2nd time and once again the trailer clearance lights would quit working. Attached are before and after pictures.
After a year doing its job well.
# 6
Bargman 7-Way Molded Trailer Wire Connector - Double-Ended - 8' Long
This cord has much better connector than most with two sided connectors, most plugs are one sided and just don't connect over time.
As usual with E-Trailer, the connector cable that I needed arrived quickly and was the right part. When I had a question about my toad wiring, they responded with an answer and an instructional video which solved my problem. Their customer service is exceptional and I will continue to do business with E-Trailer.?? G. Rusk 2007 Fleetwood Terra LX 31-M. My toad will be a 2007 Dodge Dakota FWD.
# 7
Bargman 7-Way, RV-Style Connector w/ 6' Long Coiled Cable - Trailer End
I had to replace the old 7 wire cable because the male plug had been pulled off. I chose the WH54006-043 coiled cable. I used a 1/2 inch clamp to hold the cable up at the box and a Connect-to-Protect to hold up the male plug. The result Is clean and tidy. Thank you,
This should work great, installation is still on my to do list.
# 8
7-Way Molded Trailer Wire Connector, 6' Long
Only gave 4 stars because it was a bit confusing. I have a lot of auto wiring experience; from car stereos,amplifiers and all manner of accessories. All of the info on etrailer indicated that the color coding didn't match up. So I went into it disregarding the standard color coding, when in fact it was just as it should be.
Good thick rubber and plug works perfectly.
# 9
Hopkins 6-Way Connector with Jacketed Cable - Trailer End - 8' Long
The plug was missing the set screw and collar that compresses on the cable to prevent strain on the connectors when removing the plug. You can see the set screw clearly in the product picture.
I like this style of plug because it is molded and is important in keeping water out of the plug. It is conveint because it has the right colored wires. I have a water tight termination box with studs that it is wired into. Once I damaged the cable so I opened up the terminal box installed eyelet lugs on the spare pigtail, and installed it in a fiew minuets. I keep a spare on hand with lugs on it so if I have an accident I can quickly replace it. I also use these on some of my smaller tow behind equipment. that's why I like this size plug it isn't real bulky.
# 10
Hopkins 7-Way RV Style Trailer Connector w/ LED Test Lights - Trailer End
Easy to wire and very convenient indicator lights. Only thing to be aware of is the power light will stay lit if your trailer has a battery (e.g. a camper) and so it will put a small drain on it. Not really consequential if you're properly taking care of your battery anyway (disconnect or trickle charge when not in use).
This connecter was very easy to install, and the LED display is a great addition.
# 11
Pollak Heavy-Duty, 4-Pole, Round Pin Trailer Wiring Connector - Chrome - Trailer End
very happy with product and service
What can you say about a 4 pin connector, It was what I needed and it was a good price.
What our customers are saying:
"Your internet site is very well organized and easy to use...My order was shipped very promptly and included everything I ordered...All in all this was a simple procedure for what can be a complicated order. I would use your company again or recommend you to others. Your selection was broad and your prices fair."