# 1
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
E-trailer’s website made it easy to find the correct trailer hitch for my 2019 Santa Fe. The videos on the site shows the easy installation. Great products and great assistance where I needed it. Thank you.
The good: It works. The not so good: 1. The lock washer on the ball stud makes it really hard to remove the nut. The lock washer cuts into the nut, essentially preventing it from unscrewing. This is good from a safety standpoint, but makes changing the configuration really hard. I had to lock it into a bench vice and use a pipe wrench to get it off. 2. Not sure what happened, but first time I used it (to pull a rental trailer), the hitch pin fell out, causing the trailer to disconnect. Best I can figure is that the cotter pin popped off. Fortunately, I wasn't on the highway, and the safety chains kept the trailer attached. But it was pretty scary. I replaced it with a locking pin, and had no further issues.
# 2
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
To be honest, I use it upside down. I needed a hitch with rise, but none were available at time of purchase, and yours, inverted, works perfectly! The welds are regularly checked and remain all secure. It's a good hitch.
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
# 3
Curt Multi-Ball Adjustable Ball Mount for 2" Trailer Hitches
Fits our VW Touareg perfectly and allows us to tow a variety of things now. As can be seen in the pictures the hitch has a +5-inch gap between the bumper and the vertical adjustment pillar and the trailer itself is out further so there's enough room to get to the rear hatch and maneuver the vehicle/trailer.
I needed a hitch that I could haul my work trailer with and still drop the tailgate without dropping the trailer. I looked on etrailer and found one that would work barely but decided to call etrailer and see if anyone had any ideas. Steve answered and looked after I told him my requirements and came up with this. This has a longer distance from ball to pin by a few inches compared to the one I found so my tailgate will still drop even if I’m at an angle to my trailer or on a hill. Also with the adjustable height it’s great. Awesome hitch. Solid for a good price. ??
# 4
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
Works as advertised. Great fit and now my boat is level traveling down the road. Fast turn-a-round. For [xx] shipping and the heavy weight, expected delivery in a week or two. Two days later it was at my doorstep, arriving late evening. Great service. Thank you.
I ordered the product as stated below and I received it in a couple of days. It is made well and fit into my hitch on my 2006 Santa Fe perfectly. I would recommend this company.
# 5
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.
Works great solid product.
# 6
Convert-A-Ball Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 10,000 lbs
Love these. This is my third one. Wouldnt pull a trailer with anything else. Trannys are expensive.
As a full-time RVer, e-shopping is very important for us. etrailer was the right place to shop. Right product, delivered on-time for a great price. You beat the local discount RV store by $25 including shipping. At the same time, I had another outfit send me a clearly inferior product to the one they displayed. Said they would e-mail a pre-paid shipping label for the return (didn't) and tried to put the blame on Amazon. Thanks etrailer for a great experience !
# 7
Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
works well brings the trailer tongue up to level. I have it on an EV so the raddle is annoying, because I just keep on forgetting to buy a anti rattler.
This is very sturdy hitch. It is made of solid steel, not tubing. It will be used on my Mazda RX-3 to tow my car dolly to the RV lot where I will swap everything around and the car will end up on the dolly behind my RV.
What our customers are saying:
"Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast."