# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Ordering was easy. Arrived on time. Exactly as I expected.
2nd order from etrailer, great customer service & fast delivery! My 2" ball fit the ball mount perfectly and I installed it in a few minutes. Make sure that you use a ball with a 1" shank. It stores easily underneath my Hyundai Santa Fe cargo mat until I need it.
# 2
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Ordering was easy. Arrived on time. Exactly as I expected.
2nd order from etrailer, great customer service & fast delivery! My 2" ball fit the ball mount perfectly and I installed it in a few minutes. Make sure that you use a ball with a 1" shank. It stores easily underneath my Hyundai Santa Fe cargo mat until I need it.
# 3
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 4
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
# 5
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
Nice and heavy duty
Works as advertised. Great fit and now my boat is level traveling down the road. Fast turn-a-round. For [xx] shipping and the heavy weight, expected delivery in a week or two. Two days later it was at my doorstep, arriving late evening. Great service. Thank you.
# 6
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
Nice and heavy duty
Works as advertised. Great fit and now my boat is level traveling down the road. Fast turn-a-round. For [xx] shipping and the heavy weight, expected delivery in a week or two. Two days later it was at my doorstep, arriving late evening. Great service. Thank you.
# 7
MaxxTow Tri-Ball Mount for 2" Hitches - Hollow, Black Powder Coated Shank - Chrome Balls
Good quality part. Easy Install. Used for a year so far. No problems.
Great Hitch, reasonably priced
# 8
Curt Dual Length Ball Mount for 2" Hitches - 2-3/8" Rise, 3-5/8" Drop - 7,500 lbs
Fits my Forester dealer-installed 2 inch receiver perfectly with the pin (purchased separately) in the first hole. The gas tank is in the way so I can't push it in further to the second hole. It is impressively strong, so there is no problem with it extending rearward a bit, but ideally I would get a shorter hitch if I could have a do-over, just for ease of storage.
Purchased to extend the trailer away from the back of the vehicle, and increase the drop. Initially could not fit in to my receiver, eventually figured out that the end of the 2" square was mushroomed, had to remove excess metal with a rotary tool. now it fits as far as the first 5/8" pin hole. No issues with use - seems sturdy, metal finish seems durable. Didn't drop the trailer tongue as much as I had hoped, but that's on me - I was probably running a 3" drop before, but I thought it was 2".
What our customers are saying:
"In these days of customer "no service" I am usually disapointed when doing business with people I don't know. It was refreshing doing business with you. I'm impressed!"