# 1
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
Haven’t used it yet, but looks good. I’m not sure what height offset I need, so this kit gives me several options, plus two ball sizes. Really good value.
I installed the draw tite hitch onto my brand new 2018 Subaru outback. I'm 68 years old, not as strong as I was, but proud to say I did the job all by myself in about 4 hours. Here are some tips you may find useful. Watch the video-it’s pretty good. I had difficulty getting the exhaust system down and worried about getting it up again from the moment I got it down...read on-help will follow. I bought a stepup drill bit which worked great for drilling the hole in the chasis. I clamped the hitch onto a floor jack, then rolled it and raised it into position. Used metal shears to easily cut out the heat shield as per the video. Your inclination will be the screw the fishing tool provided all the way up the carriage bolt. That won’t work; just screw it on to the tip of the bolt. I couln’t get the exhaust hangars in place even after lubricating them with wd-40. I dropped the rubber hangars into undiluted liquid car wash soap which made them much more slippery than the wd-40. After that the rubber hangars slipped into place pretty easily-that’s my best tip. Finding the electric connection plug for the wiring harness was almost as hard as installing the hitch. I was very happy with how the job came out. Good luck.
# 2
etrailer Ball Mount Kit for 2" Hitches - 2-3/4" Rise or 4" Drop - 7,500 lbs
Like the product which seems very heavy-duty. The two ball mounts give me options for towing different trailers if I need it.
Nice kit. Every thing I needed. Looks good too
# 3
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Sara R was helpful helping me find the right hitch for what I described as needing. I was excited to see the hitch pin in my order details even though I didn't order it. Sadly, the picture gave me a false impression. Overall, excellent customer service and product.
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
# 4
Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
works well brings the trailer tongue up to level. I have it on an EV so the raddle is annoying, because I just keep on forgetting to buy a anti rattler.
This is very sturdy hitch. It is made of solid steel, not tubing. It will be used on my Mazda RX-3 to tow my car dolly to the RV lot where I will swap everything around and the car will end up on the dolly behind my RV.
# 5
Curt Class III Ball Mount with 2-5/16" Ball - 2" Rise or 4" Drop - 7,500 lbs
This was purchased for towing a 7k GTWR utility/landscape trailer with my 2018 Chevy Silverado 1500 WT 4x4. I measured for necessary drop before ordering, and the 4" drop is darn near perfect. It's a great help that the 2-5/16" ball comes complete, installed and torqued properly at the factory. Appears to be quality construction, fits and functions perfectly. I have no complaints or issues.
The Curt Class III ball mount arrived as promised and the product is as advertised. My whole experience with the process was top notch from ordering to delivery, installation, and use all 5 star.
# 6
Curt Class II Euro Style Drawbar with 1-7/8" Ball - 4-5/8" Rise - 3,500 lbs
Perfect for my Honda Fit as it has a low carriage, the Euro shape gave me a few extra inches to tow a small trailer across the country from Oregon to North Carolina with no issues.
Love this hitch. It looks and fits my Optima perfectly. I was really pleased to find a modern looking hitch to fit on my car. Very strong, solid construction. I don't plan to pull a large trailer with my car but this will work perfectly for my utility trailer. Very friendly and helpful customer service and it was delivered faster than I hoped for. Extremely pleased. Thanks...
# 7
Curt Class III Drawbar - 2" Rise - 4" Drop - 13" Long - 7,500 lbs
Haven't used it yet. I bought it because of CURT's quality. It was beat up in shipping though.
This 13" drawbar keeps the tailgate off the trailer jack. Being that long also keeps it I storage immediately after I disconnect the trailer. No need for a locking pin.
What our customers are saying:
"Very easy process, good prices and my products were shipped on time and were delivered on time. The instructional videos online helped make installation easy!"