etrailer Ball Mount Kit for 2" Hitches - 2-3/4" Rise or 4" Drop - 7,500 lbs

Ask the Experts about this etrailer Trailer Hitch Ball Mount

• Recommended Trailer Hitch Ball Mount Rise for U-Haul Trailer Coupler for 2015 Mazda CX-5
  On your 2015 Mazda CX-5, the measurement you need is from the ground to the inside top of the receiver. If you look at the attached video we that measurement listed at 15-1/2 inches so it is different from the 13 inch you referenced. For your 13 inch measurement you will then need a 5 inch rise. I recommend the B&W Heavy-Duty Ball Mount - 5" Rise, 6" Drop - 10-3/4" Long - 16,000 lbs # BWBMHD30014 or the Curt # C45336 and then you will need the # A-90 hitch ball. The pin and clip...
  view full answer...
• Can Hopkins Wiring Harness for 2013 Subaru Outback be Stored in Hatch When Not in Use
  You can absolutely store the Hopkins Plug-In Simple Vehicle Wiring Harness # HM11143865 in the hatch of your 2013 Subaru Outback when you aren't using it instead of routing it outside the vehicle. The connector end will be long enough to hang outside your hatch when you need to connect it to your trailer. I have added a link to the instructions and a video install for you to check out as well of the Hopkins Plug-In Simple Vehicle Wiring Harness # HM11143865. If you also need a trailer...
  view full answer...
• Comparing Draw-Tite Trailer Hitches for 2018 Ford Edge Titanium & Edge Tongue Weight Capacity
  Let's start simple, which is the difference between the Draw-Tite Trailer Hitch # 75234 (square tube) and Draw-Tite Trailer Hitch # 75214 (round tube) that fit your 2018 Ford Edge. The difference is mostly just in the aesthetics, with the square tube hitch having a concealed crosstube, and the round tube hitch having a visible crosstube. The square tube hitch also has a higher overall capacity of 4,500 lbs towing and 675 lbs tongue weight compared to 4,000/600 of the round tube, but since...
  view full answer...
• How to Choose Correct Ball Mount for Draw-Tite Hitch on 2017 Tesla Model X
  To choose the correct ball mount you'll first need to measure from the ground to the top inside of the Draw-Tite Receiver # 76143 with it installed on your 2017 Tesla Model X, and then from the ground to the bottom of your trailer coupler with the trailer sitting level on level ground. Since the hitch receiver sits fairly low I'd imagine that your trailer coupler will be higher so you'll need a ball mount with a rise like the 2-3/4" rise ball mount that comes with the etrailer Ball...
  view full answer...
• Which Panel Needs Removal to Install Trailer Hitch on 2019 Mazda CX-5 GT
  The panel that would need removal is located between the bumper and the muffler as shown in the provided photos and install video which shows the installation of the # 76138 hitch. The placement of the trim piece would interfere with the installation of the hitch so it would need to be permanently removed. The trim piece is meant to make a slight improvement to the vehicle's aerodynamics. If you'll be towing with your CX-5, you'll also need a ball mount, trailer ball and a trailer wiring...
  view full answer...
• Will Aftermarket Trailer Hitch Installation Void Warranty on 2020 Honda Odyssey
  Absolutely not, you are protected under the Magnuson-Moss Warranty Act, which makes it illegal for companies to void your warranty or deny warranty coverage simply because you used an aftermarket product, unless they can prove the aftermarket product caused the problem. With that cleared up, the hitch I recommend for your 2020 Sorento is the etrailer.com Trailer Hitch # e98855 because its installation is pretty simple and straight forward and does not require fascia trimming. I'm...
  view full answer...
• Hitch, Ball Mount and Wiring Harness Options for 2012 Buick Enclave Without Factory Tow Package
  For your 2012 Buick Enclave the Draw-Tite 2-inch Class III hitch # 75528 is a confirmed fit. Install instructions and a complete install video are linked for you. The hitch comes with all needed hardware. You will also need a ball mount, hitch ball and pin/clip. I suggest ball mount # 989892. In terms of the wiring harness options you ask a very good question. The available products, non-powered models # 118450 and # C56027 and the powered converter model # HM11141615, differ in one...
  view full answer...
• Recommendation for a Ball Mount to Fit a Hitch on a 2014 Ford Edge
  For the Draw-Tite hitch, # 75992, that will fit your 2014 Ford Edge, I recommend the etrailer.com Ball Mount Kit for 2" Hitches - 2-3/4" Rise or 4" Drop - 7,500 lbs, # 989892. This ball mount kit will include a ball mount that will fit the 2 inch receiver opening on the Draw-Tite hitch. The ball mount will provide 2-3/4 inch rise or 4 inch drop. The kit will include a 2 inch trailer ball with a 7,500 lbs gross towing weight capacity and an 1-7/8 inch ball with a 2,000 lbs gross towing...
  view full answer...
• Will the Draw Tite Trailer Hitch Receiver # 75600 Fit a 2008 and 2015 BMW X5
  Yes, the Draw-Tite hitch # 75600 will fit a 2008 and 2015 BMW X5. On the 2015 it will not fit the M model though. This is a Class-III hitch with a gross trailer weight of 6,000 pounds and tongue weight maximum of 600 pounds. I recommend checking your owners manual or local dealership to verify your towing capacity of your 2015 BMW X5. Please note that after 2010 the plastic push rivets included won't work. You will need to obtain them from BMW for models beginning in 2011. If you...
  view full answer...