# 1
Wet Equalizer Bolt with Locknut and Grease Zerk for Double-Eye Springs - 3" Long
The wet bolts were just fine. But the "locking nuts" with the crimped edges were aweful. The 3 dimples each nut has were not useful. Many of the nuts I could use my fingers to spin them on the bolts. Never had locking pressure. I ended up going to local hardware store for much better locking nuts.
# 2
U-Bolt Kit for Mounting 5,200-lb to 7,000-lb, Round Trailer Axles - 7-1/16" Long U-Bolts
the web site has alot of good info that will answer any questions. I recieved my order in a week and shipping was free. all parts fit well except for the u bolts being too long. I cut them to fit my axles and springs.
Working great as I had expected. Always great to deal with etrailer
# 3
2" Square Trailer U-Bolt (Qty 2)
Nice and heavy duty.
Had a leaf spring break on my off-road trailer in Mexico. Left it at a boat yard until I received the parts from trailer & returned to replace. Only took 2 hrs to replace both leafsprinhs, shackles, bolts etc. And we were back on the road.
# 4
Single-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front, 7/8" Rear
This is a great kit! It included everything we needed to replace the old, worn-out brackets on our 6'x10' trailer. The directions were helpful and the brackets and hardware are nice and solid. We've had zero issues with the leaf springs (purchased on etrailer.com, also) or the brackets. Would definitely recommend!
Excellent, had everything I needed and more for my trailer. Everything fit well!
# 5
Front/Center/Rear Hanger for Double-Eye Springs - 4-1/4" Tall - 9/16" Bolt Hole
great deal and fit to my order and fast shipping
These were purchased to assist with raising a dual-axle travel trailer. They arrived well packaged, and looked to be well made.They took readily to welding, so there was no issue with inferior material. The attached images show them being welded side-by-side to the frame rail extensions, then the entire assembly attached to the main frame.
# 6
Wet Equalizer Bolt with Castle Nut, Grease Zerk and Cotter Pin - 3-1/2" Long
This is an excellent product, but I gave it four stars because it was nearly impossible to install with ordinary tools. It was necessary to force the serrated portion into the center hanger and since I did not have access to power to run a compressor and force it into the hole using excess torque via an air wrench, I had to use a hammer to drive the serrated end into the hanger. I found an install video from etrailer that showed how the installation was to be done, but I could not accomplish it that way. Besides the amount of torque needed would probably have twisted the bolt off at the grease hole. As it was, I drove the part in with a 3# hammer after destroying ordinary white wood blocks of wood. I removed the grease zerk and used another piece of flat iron to protect the zerk's threads. I was able to bottom the head against the hanger by tightening the nut as much as I could by hand and then hitting the head with the hammer a few times, tighten again, etc., until it was completely in place. This method was used on both sides of the trailer. To torque these into position with an ordinary wrench would have exceeded 1000 lbft of torque which I am not sure that these bolts would take without damaging them more than the hammering did. To be fair, the information suggested that the hangers be replaced, but that was because many times the hangers are damaged if the other parts wore out. But it is fairly clear that the holes in the hangers are not pre-formed with matching serrations so I doubt that it would have changed the issue. In short, I don't believe that the serrated portion is necessary. And if it is, then a keying method would be more appropriate, such as a square hole.
I am rebuilding my tandem axle utility trailer and the center shackle bolts were rusted tight. Upon removing them, they were also badly worn. I went into my local auto parts store and they didn't carry nor could they get through their suppliers the replacement size. Only place I could find the 3/4" zerked bolt was eTrailer.com. I ordered two, they arrived quickly and were the exact size I needed. They installed easily and are working great!
# 7
U-Bolt Plate for 2" Square Axle - 1-3/4", 2" Springs - 9/16" Bolts
Good quality and heavy duty.
Had a leaf spring break on my off-road trailer in Mexico. Left it at a boat yard until I received the parts from trailer & returned to replace. Only took 2 hrs to replace both leafsprinhs, shackles, bolts etc. And we were back on the road.
# 8
Step Wet Bolt for 1-3/4" Double Eye Springs
I appreciate your informative response to my questions. The RV leaf spring is exactly what I needed. Thank you and I will continue doing business with you. Thanks to Dan for helping me place this order.
Exact duplicates of the stock Dexter equalizers. Removed nylon bushings and replaced with steel bushings with wet bolts.
# 9
2-3/8" Round Trailer U-Bolts (Qty 2)
I purchased these u- bolts to go along with the new 3500lb axle I purchased from etrailer for a 12’ utility trailer. Once installed the trailer tolls better than even when new. I highly recommend etrailer for all trailer needs.
Disappointed that this could be sent out like this. The one package came with one ubolt and three nuts. In undamaged packaging.
# 10
Tandem-Axle Trailer Hangers for 1-3/4" Wide Double-Eye Springs - 3-1/4" Tall Front
Worked for what I needed. No issues so far.
These are the lippert brackets, I bought for spares just in case I was to break one in travels. Alsome product.
What our customers are saying:
"Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast."