Summer Starts Here - Save up to 70%
# 1
Draw-Tite Drawbar for 1-1/4" Hitches - 5" Rise - 10" Long - 3,500 lbs
This is the correct towbar for a Toyota Prius C. The towbars that are available from U-haul (3 1/8") and other hardware stores are too low to the ground for most trailers. I tow my Harley Dyna on a motorcycle trailer behind my Prius C with no problem. Save yourself the grief. I bought three readibly available tow bars until I found the right one. The 5" rise, 10" long works perfectly. This is an incredibly strong drawbar.
Worked perfectly Did have to grind off the paint and a nit of metal to fit in the reciever though.
# 2
Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-3/4" Long - 3,500 lbs
Easy ordering, fair pricing, prompt delivery...product arrived in excellent condition, very heavy duty drawbar for use with by 4ft x 8ft medium duty trailer.
Solid quality and workmanship.
# 3
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Drawbar looks great and will be using in next two days. Thanks!
# 4
Draw Tite Drawbar for 1-1/4" Hitch - 5/8" Rise, 1-1/4" Drop - 9-3/4" Long - 3.5K
Works perfectly for me. I use it to tow a motorcycle trailer behind my Mini Cooper with a concealed hitch so I need the extra length to clear the bumper. No complaints.
Excellent quality, solid steel bar and wields are excellent. The black coating is heavy and well applied. I’m Very happy with this product!
# 5
MaxxTow Ball Mount w/ 2" Accessory Receiver - 2" Hitches - 2-1/4" Drop - 5,000 lbs
Heavy duty , very good quality.
# 6
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 7
Draw-Tite Ball Mount - 6-3/4" Rise, 8" Drop - 10" Long - 5,000 lbs
Just Alright - made in CHINA I ordered this per etrailer's suggestion to use with a Curt Class III Receiver Hitch on a 1999 Ford Windstar to pull a pop-up camper. The ball mount (which is made in CHINA) is built very solidly , but there seemed to be a lot of play once inserted into the Curt receiver. There was a lot of clunking around back there while either accelerating, braking, or simply pulling. I ended up wrapping the ball mount shaft with a layer or two of duct tape to tighten things up a bit and alleviate some of the obnoxious clunking. The Ford Winstar pulls great. The Curt receiver is as good as they get (and made in the U.S.A.). The Drawtight ball mount seems to be the weak link in my setup. Next time I'd go with a CURT ball mount. Plus CURT is made in the U.S.A
Works great, a little loose in the receiver just like any other hitch I have used.
# 8
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Just Alright - made in CHINA I ordered this per etrailer's suggestion to use with a Curt Class III Receiver Hitch on a 1999 Ford Windstar to pull a pop-up camper. The ball mount (which is made in CHINA) is built very solidly , but there seemed to be a lot of play once inserted into the Curt receiver. There was a lot of clunking around back there while either accelerating, braking, or simply pulling. I ended up wrapping the ball mount shaft with a layer or two of duct tape to tighten things up a bit and alleviate some of the obnoxious clunking. The Ford Winstar pulls great. The Curt receiver is as good as they get (and made in the U.S.A.). The Drawtight ball mount seems to be the weak link in my setup. Next time I'd go with a CURT ball mount. Plus CURT is made in the U.S.A
Works great, a little loose in the receiver just like any other hitch I have used.
# 9
Curt Class III Drawbar - 2" Rise - 4" Drop - 13" Long - 7,500 lbs
Haven't used it yet. I bought it because of CURT's quality. It was beat up in shipping though.
This 13" drawbar keeps the tailgate off the trailer jack. Being that long also keeps it I storage immediately after I disconnect the trailer. No need for a locking pin.
# 10
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Works great.
Just Alright - made in CHINA I ordered this per etrailer's suggestion to use with a Curt Class III Receiver Hitch on a 1999 Ford Windstar to pull a pop-up camper. The ball mount (which is made in CHINA) is built very solidly , but there seemed to be a lot of play once inserted into the Curt receiver. There was a lot of clunking around back there while either accelerating, braking, or simply pulling. I ended up wrapping the ball mount shaft with a layer or two of duct tape to tighten things up a bit and alleviate some of the obnoxious clunking. The Ford Winstar pulls great. The Curt receiver is as good as they get (and made in the U.S.A.). The Drawtight ball mount seems to be the weak link in my setup. Next time I'd go with a CURT ball mount. Plus CURT is made in the U.S.A
# 11
Curt Drawbar for 1-1/4" Hitches - 5-3/8" Rise, 6" Drop - 5-9/16" Long - 2K
I used this on a 2014 Ford Fusion with a Reese receiver hitch made for my vehicle. Either the neck of the drop hitch is not long enough to get the ball a few inches away from the vehicle or the Reese receiver hitch sits too far under the vehicle.
Untried as of yet but looks like a quality product. It's difficult to provide an accurate review of a product one just received, but I was very impressed at how quickly my order arrived (days before the expected arrival date), as well as the ease of ordering, the price, and the follow up.
# 12
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
What our customers are saying:
"Easy place to shop. Fast delivery and great products. Very happy with my purchase."