Most Popular Hangers for 1989 Toyota Camry

Well constructed

Bought this to replace the shackle links and hardware for an existing aluminum trailer, did not use the brackets. Bolt shafts are "flared" on the inside head end so you need a press to push them into the bracket. Otherwise, you need to crank down the nuts as you install them to seat the bolts properly.

My 6' x 10' landscape trailer was a homemade by a prior owner. While it was mostly constructed very well, the spring hangers were not correct. The spacing for the springs was also wrong, and it had very little fender clearance. There was also evidence that the spring U-bolts had contacted the frame on occasion. (I do not carry loads anywhere near the 3500# axle rating.) I added an extra set of holes on the front hangers in case the ride height proved to be too much, but I like the way it sits with the stock holes. I don't think I'll be utilizing the extra holes. This kit was just the ticket to increase the suspension travel and fender clearance on my landscape trailer. Now it "sits right"!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

I am sorry but I can not remember names but I talked with two very helpful ladies and could not have been happier with their assistance. Thanks again, the trailer build is going great.

Worked for what I needed. No issues so far.

These are the lippert brackets, I bought for spares just in case I was to break one in travels. Alsome product.

This is a great kit! It included everything we needed to replace the old, worn-out brackets on our 6'x10' trailer. The directions were helpful and the brackets and hardware are nice and solid. We've had zero issues with the leaf springs (purchased on etrailer.com, also) or the brackets. Would definitely recommend!

Excellent, had everything I needed and more for my trailer. Everything fit well!

Click to Enlarge

Click to Enlarge

It works fine for my application.

Exactly what I needed. Great service and fast shipping. Thanks.

I used these 'front' brackets for both front and rear ends of my leaf springs, because I couldn't find a bolt-on rear bracket. I had to bend 1/4" offsets into each of my rear shackles to make the rear brackets work. I added a spacer between my shackles to keep them perpendicular. The original rear clip was 1-3/4" wide on the outside and the shackles were outside the clips. I used 3/8" bolts to attach the brackets to my 3"x1-1/2" steel tube trailer frame. The bracket mounting tabs are drilled for 7/16" bolts, and I would have preferred to use 7/16" bolts, but I couldn't find that size at my local hardware stores. I moved my axle forward to rebalance my boat trailer, because I put a smaller engine on which made tongue weight way too heavy. I went with bolt-on brackets because I could do it myself (I don't have welding equipment). Overall, I'm satsified.

Click to Enlarge

Awesome product. great delivery service... Product will be used to hang thr leafsprings on my boat trailer.

Click to Enlarge

Just as good as the ones from the big box stores but way cheaper.

This is a multiple product review. The long bracket are good. The shorter brackets are of the same good quality. The issue is using the short brackets with the shackles. The shorter brackets could be narrower so the shackle line up better with spring and other longer bracket. We used washers to make it align better. The greasing bolts are good, but could be longer. so we could only use 2 of the 6 and had to use normal grade 8 bolts.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Worked as it should. New hangers, and a new axle and back on the road.

Website was easy to navigate and price was great. Parts are exactly what I needed to repair an older trailer that gets pulled several times a week

I think etrailer is Great. I think their customer service is fantastic. My wife and I were in Arkansas, 1200 miles from our home in Ft. Myers Florida. I replaced the original springs on our trailer with new heavy duty springs, but never changed the hangers or bolts. Our trailer was riding very poorly, we needed new hangers and bolts badly because we were headed on a very long 9000-mile trip with many stops all the way to the Monterey CA. etrailer found us a UPS Store along our route to send us the parts that we needed. Many thanks to etrailer for great parts and Fantastic customer service and for helping us with our most Wonderful Adventure!

Click to Enlarge

Product was as advertised and work perfectly. I like your company and have purchased many items from you. The shipping was very good and arrived shortly after the purchase.

This kit (a dual kit) changed my view of Dexter as a quality-first manufacturer. etrailer simply sells it, they don't make it, so they aren't to blame. This kit is made specifically for mounting Dexter's General Duty 9,000 lb axles in tandem and is different from kits made for 3500 to 8000 lb axles. It provides extra axle tube to frame clearance to accommodate the 4" axle tubes used on their 9k and 10k GD axles. It uses beefy 7/8" equalizer pivot bolts and 5/8" spring eye bolts. So far, so good. Until you pay over $350 for it and receive a suspension kit with absolutely ZERO lubrication provisions! Seriously, Dexter?!! The bolts provided are all just grade 5 hardware store plain jane dry bolts. Not even grade 8. Dexter sells 7/8" greaseable "wet bolts" and even their lighter-duty hanger kits include greaseable wet bolts. But even if I paid etrailer the nearly $XX apiece they want for them (they're half that price elsewhere), there is literally no way of putting a square-shouldered carriage-style bolt, which they are, in the round roles this hanger kit was manufactured with without modification. As for the 5/8" spring eye bolts, only a great deal of internet searching will find any wet bolts the right diameter, and they'll be the wrong length. Those 4 bolts are about $20 each plus shipping. So, by the time I pay a machine shop to square the equalizer bracket holes on and buy all the wet bolts, or have them made, JUST so I can lubricate this expensive hanger kit in hopes of it lasting more than a very short time on a trailer that often grosses 20k, I'm going to have over $500 invested in it, not counting all the extra wasted down-time. This kit was supposed to solve my trailer suspension problems, not create more. FAIL!!

I purchased the 7 leaf sliper spring to replace my old ones. etrailer had all the parts needed to rebuild my trailer. The parts fit perfectly. The people there are very knowledgeable about the trailer parts and what is needed and what will fit when replacing old worn parts. I would stronly recomend etrailer for any of your trailer needs.