Summer Starts Here - Save up to 70%
# 1
Brophy Cable Camper Jacks - 67" Max Lift Height - 3,000 lbs - Qty 2
Great directions for manual assembly, quality metal and parts. Solid and exactly the heavy duty I was looking for to use with my slide in truck camper.
The Brophy jacks were strong, stable, easy to position, and easy to lift and lower my camper. it is a much better method than having four jacks to maneuver. And it cut down my time to 30 minutes total to load my camper instead of an hour and a half! I have to start from my garage and winch my camper down on a cart to the street face because of the incline driveway is so dramatic and my camper won’t fit in my garage if it is attached to the truck. I couldn’t be more happy they were great and now I have my truck loaded with my very modern camper and I’m enjoying quite the holiday! I’m using the 3 ton 67 inch trophy jacks and I’m lifting an 800 pound gross camper. The stability is outstanding.
# 2
Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 24" Lift - 3,500 lbs - White
Jack works very well. Not fast but gets the job done. Unfortunately I can't lower my tailgate fully without hitting the jack. Tried to rotate the head as I saw some jacks allowed. This one won't allow that. Very satisfied otherwise. Used less than one full season so can't offer an opinion on durability.
Mounted quick and easy. Plenty of wire for electrical hook up. Lots of power even with a full load of water in the front tank. The only change I made to installation was longer bolts to accept washers and nuts to the bottom side of hitch. I didn't trust the taped holes in the thin hitch frame. This was no fault of the new jack. Still working strong. A back saver that's worth the money. I should have bought one years ago!
# 3
Lippert Power Stance Electric Trailer Jack w/ 7-Way Plug - A-Frame - 18" Lift - 3,500 lbs
The alternate power setup makes its slow rate of rise necessary which would be good if my lithium batteries went low. To avoid battery problems be sure to add an inline battery disconnect from the trailer power when using tow vehicle power. I simple added an inline fuse that could be removed should I need to use the tow vehicle power.
I was amazed at how quickly my replacement from etrailer arrived. I was a bit worried that the installation of my new jack would be more difficult that I expected. The reverse proved to be the case, it was very simple to place the trailer tongue on jack stands, remove the old jack and install the new one. As the old saying goes "even a cave man could do it."
# 4
Lippert Electric Trailer Jack with Footplate - A-Frame - 18" Lift - 3,500 lbs - Black
The bolt pattern matched my trailer so it was very easy. No skill needed. I soldered a connection on and hooked it directly into the battery. I had to drill a hole for my foot extension. So far so good. 23 foot travel trailer.
As always a big help in getting what I need, and wanted. Good tec help, fast service. Already installed.
# 5
Electric Trailer Jack - Drop Leg - A-Frame - 22-1/2" Lift - 3,500 lbs
The CargoBuckle G3 ratchet tie-down straps and 45 degree mounting brackets worked great. Makes loading and unloading a breeze.
This jack was the perfect solution for my application. I have a new enclosed trailer that came with a manual crank and only a tiny battery to run the lights. I did not want the expense of having to buy and cable up a larger battery to just support the tongue jack. Took me 5 minutes to install this new jack using the three bolts that were already on my OEM jack. Now I just back up my truck, plug in the 7-way, and I'm able to move the tongue up and down as needed. Great!
# 6
Electric Jack w/ Footplate and 7-Way Plug - A-Frame - 25-1/8" Lift - 3.5K - Black
The 7-way plug electric jack is a great replacement for my crank handle jack. I did not want to install and maintain a 12V battery for just a jack so this is an easy plug and play solution for me.
7 pin easy hook up for trailer jack does not work on my 2020 ford ranger. Missing 12v power to jack control? any advice in Trouble shooting. Is there a compatibilty problem with ranger to your jack 7 pin config? Will use manual hook to battery rather then ask for replacement jack if possible?. Before I cut any wires and void warranty. Is all I have to do is cut and splice the fused red wire to a positive battery terminal to do this. What abount grounding? Please advise should I modify and wire direct or return jack back for refund/replace
# 7
Brophy Cable Camper Jacks - 57" Max Lift Height - 3,000 lbs - Qty 2
"Box was badly damaged on arrival. I opened the box and discovered the lift tubes were not there. After contacting customer service they let me know the missing lift tubes were in separate shipment. Customer service was kind and very friendly and got the tracking number of the separate shipment. They gave me the new delivery date and said I could call anytime for updates. Everything came as it should be despite the boxes being pretty beat up. That's really the only reason for 4 instead of five stars. etrailer's dedication to customer service is far above industry standards in my opinion and would definitely recommend them for this alone. I'll post another update with the jacks in use."
For near 600 dollers I wish more care would of been taken on packing these jacks
# 8
Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs - Black
Replaced stock Air Stream power jack which started making grinding noises. New 4,000 pound jack easy install and works fine. Using it to lift 25ft trailer and 2500hd Silverado to attach anti-sway bars. Had to mount it sideways due to propane tank cover, but it works great. Had one of these on a larger trailer that a hurricane destroyed. Nice unit and easy install.
Overall the product does exactly what it's intended for and works well. I however assumed that this would be a simple R&R for my camper and did very little installation research other that the video provided on etrailer' s website Sadly it did not fit. Not at all. I didn't take into account that have a double framed hitch toyhauler. The baseplate on the factory leg was a TRIANGLE.....this unit was ROUND. Also the primary shaft was thicker than stock and would not drop down into place I know modifying is frowned upon, but I found that ALL powered hitch legs I found have round mounting plates and it's not mentioned the leg tube is thicker than OEM? Since NOT having a power lift wasn't an option for this camper application...too heavy in the front when ATVS loaded to lift for setting the equalizer hitch tension bars, I proceeded to modify by cutting the rear rounded mounting base ... square. Took off about 1/2 inch. Then I took my metal Dremel sanding bit and increased the hitch leg hole diameter slightly. Took about 1 hr. Dropped it in. Wired it. Tested it. All good. If you can't post this I understand, but take note that some of your website descriptions may need to be enhanced. Thanks!
What our customers are saying:
"Quick processing, and delivery. reasonably priced very satisfied"