Summer Starts Here - Save up to 70%
# 1
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Works good with my snow plows.
I just had a chance to finally get it mounted to my truck. The fit is perfect. I have never had any issues with anything that I’ve ever gotten from etrailer.
# 2
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
This worked great on my F350 dually. We needed a front hitch to carry bikes while towing a 5th wheel camper. Instructions were easy to follow
I buy practically all my towing accessories from etrailer. One of the reasons why is that you can tell that they take the feedback of their customers seriously. I read a lot about previously shipped products having fell out of the box in certain areas. etrailer heard that feedback and my shipping box was reinforced in just the right areas that were talked about getting punched through in shipping. The tech notes video on the 2012 F-250 applied exactly on my 2016 F-250. All the measurement specifications were correct as well. This is a job that can be done by one person, albeit you'll have to be careful. Your second set of hands can be jack stands, as it was in my case. If you take your time in positioning everything - installation will be a breeze. I do agree with previous reviews - it would be nice to have a second fishing wire as it does get stretched out when pulling the first bolt through. That, or a heavier duty gauged wire - that's just a small detail however. If you're really concerned about it, you can buy a secondary fishing wire at around 5 bucks. I spent more time taking out and putting back in body clips than I did with the install of the hitch receiver hardware. I really like the way it looks and I'm excited to use it.
# 3
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
It was a bit harder to put on than they show in the video. Did it by myself, everything fit perfect SO OWSOME! I would recommend anybody. Truck or car should add one. Very convenient and can be use for many different purposes.the rack on the back, I now put in the front with generator gas tools and it works as steps. So now I can tow trailer, or jet ski. Having that front hitch is so cool. You could even attach a car whinch in the receiver.
Got this on my 2006 2500 Ram. I did avoid drilling the holes over 1 inch (suggested in the directions) by loosening the bumper bolts and prying out some brackets in the frame ends temporarily (just to get the bolts fished thru). I pushed the brackets back in after getting the bolts in place (and believe the bumper bolts will squeeze them to hold them), but I did bend some tabs that I can't get back to original. My bumper bolts on the driver side wouldn't go in far enough (hitting a cooler) to be totally flush for a completely vertical lift into place, so I had to swing it up there first, then do the passenger side. The first pair of bolt fishing went good, but then I had trouble getting the wires off the bolts (they were tight enough that the more I tried to twist them off, the tighter they gripped it). So instead of them coming off like twisting a nut off, I ended up peeling them off (with the bolts staying stationary and my peeling the wire around them). That slightly bent the wires so they were slightly bigger than the threads and while fishing the second set, the wire didn't stay in the threads and jammed the bolt in the hole a bit (but I still got them in place). So watch how you treat the fishing wires until done. I already have a winch mounted on a hitch bracket, but may use this for more things besides that.
# 4
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Great products, great prices, fast shipping and a great company to do business with. Easy install, and it took longer to trim the air dam than installing the hitch.
I have had this hitch installed for just over a year now on my '99 2-door Tahoe. The install was pretty straight forward, and the hitch itself has held up quite well through a year's worth of abuse. I use it to run my bike rack out the front; the receiver protrudes just below the factory front bumper, maximizing ground clearance when adding length to the front of the vehicle. And as you can see, the kit comes with two sets of hardware in case you want to maintain the factory tow hooks like I have.
# 5
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~
Relatively easy install. Just have to be mechanically inclined. We use the hitch to carry a fish rack/cooler on a 2011 Jeep Wrangler. So far so good.
# 6
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Install went perfectly. It all bolted up just how the instructions said it would. The hardest part was navigating your tools in the tight spaces. Having the deep sockets as suggested is definitely worth it. I was also able to utilize a cordless impact wrench and it helped a ton. This will work great for our bike rack.
Delivery was super fast, instructions and instructional video was excellent. Installed my new part in less than 40 minutes
# 7
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Very easy to install. works great for bike rack and generator box.
After struggling with the answering menu, Steve Z. was instrumental in locating a hitch to fit my van which was not specifically identified in any data search. Weird year, 2005, of popular Chevy Express van, my luck! Using manufacturers dimensions I purchased #31016 on 12/21 and it arrived on 12/24. It's a very well built, USA built, unit. It arrived rapidly, but was missing half of the mounting hardware. The remainder of the hardware was rolling around in the box. Zip lock baggie ripped apart spilling them. I used a hydraulic jack to elevate hitch into place, and an additional jack to push the drill up to drill the 6 mounting holes necessary. No factory hole alignment. All the nuts for the bolts were lost in transit, but by a Christmas day miracle, I found 2 metric nuts to fit supplied bolts that survived the delivery. I will acquire, and install remaining missing 4 tomorrow. The installation went smooth and easy using this technique. It took around 3 hours with much of the time searching for hardware.' Thanks Steve Z. and etrailer. .
# 8
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Great customer service and product.
The quality and fit is exceptional. So much so that this is the third hitch assembly I've purchased and installed. This one was for my brother in-laws 1999 F350. I also put a 10k winch on a slider that works perfectly with this assembly. Other vehicles I purchased and installed assemblies on are a 2011 F350 and a 2016 Class C motorhome. Very happy.
# 9
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
2007 Toyota TundraThis was one of the easiest accessories I’ve installed on my Tundra. It is a front receiver hitch so I don’t use it very often. Mostly just for bike racks when towing a trailer, but when you need it you need it.
Straight forward and perfect fit on my 2008 Toyota Tundra!!
# 10
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
How it was received; either is was mail destroyed or UPS did this in the process. No telling what parts are missing, waiting for UPS to come pick this and E-Trailer to send out replacement. I thought these product would be packaged better from the factory for shipping resilience.
This hitch was very easy to install....I had to trim the lower air dam to fit around the receiver and that gives it a clean neat look. I didn't like that I had to remove and leave the shields around the tow hooks off. But overall I'm very pleased. I plan to use this hitch for maneuvering a camper in a narrow spot beside my home, and for a bike rack when towing a camper.
# 11
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
It installed as advertised and fits perfectly. I haven't used it yet, but it will make positioning my trailer in my backyard much easier!
Would like to just take a moment To thank etrailer for getting our draw tight front mount hitch and our swagman bike rack to us. It certainly solved our problem. For sometime we have wanted to take bikes camping with us and have not had a proper place to haul them. The camper has a molded bumper and I certainly didn't want to haul them in the camper. So my hat off to you on both products
# 12
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Quality hitch and the excellent service all the way around I'm used to getting from etrailer over the years. Installed on my 2016 Sierra Denali 2500HD, note instructions say on first line down that it does not fit the Denali trim due to extensive fascia cutting required; actually it was quite simple with the aid of a 4-1/2" cutoff disk and a sawzall. Installation is much easier with two people. See attached pics for actual material removed, note the lower fascia need not be cut for the hitch to fit through the hole. Maybe more work to install than the Curt hitch, but well worth the additional ground clearance.
The hitch was easy to install. The only issue is who ever welded it put the front ring on and it's turned to one side. It functions fine but bothers my OCD.
# 13
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
1996 Chevrolet SuburbanI have had the front receiver hitch installed on my 1996 Suburban for about a year now. I have a 12000 lb winch installed using that receiver hitch. I have gotten stuck twice and had to use the winch to extract the truck. Very glad that I have the front receiver hitch as it made putting on the winch very easy. Also useful for mounting a receiver mount bicycle rack to the front as well.
Product was shipped promptly and arrived a few days later. Packing was good for a heavy item with pointy edges, no issues breaking out of the box. Installation on a lift took about 30 minutes on my 1999 K2500 Suburban. The bolts were long enough to allow for my tow hooks that were already in place. A bolt stringer to pull the rear bolts from the top (inside the frame) is provided along with nuts, the other four just replaced the stock bolts that I had that mount from the bottom into tapped frame metal through the tow hooks. Curt makes great quality stuff. Clearance was reduced a little but I'm not concerned about it.
# 14
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
The hitched arrived three days early and I was able to install it in less than 2 hrs with a little help from my wife and a floor jack. Perfect fit!! No shimms necessary Vwrry happy.
2002 Chevrolet SilveradoThe hitch installed easily on the front of my truck and has given me more versatility in using my truck. In the summer I carry 3 bikes on a hitch rack when I go camping. I also hook up a 12000 lb. winch when needed. Sometimes I use the front hitch when moving my boat. This is a very sturdy and reliable hitch. Etrailer customer service is excellent.
# 15
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Ford F-150This receiver performs well for both bicycle and motorcycle carriers. It is not obtrusive when not being used. It was easy to install with no drilling required (You do have to cut out the air dam.). I would have given 5 stars if would’ve fit a little higher. There was room for it to be at least an inch further off the ground. I ended up putting a 1 inch leveling kit on the front of my 2 wheel drive F150 and it turned out great and the truck looks better too
I am very pleased with this equipment. Bought it to carry two heavy E-bikes. Installation directions could have been clearer--but with the help of videos, I got it in just fine. Had to use a large crow bar to urge it in place though.
# 16
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Road tested 4000 miles & off-road, Solid, Great ! I always wanted a front hitch, it is rad ! We had a great experience across the board. Ordered the front hitch mount and had a mechanic (Weld Tech/San Diego) install it, because they already had our van to install their lift kit. They charged me one hour labor. I can see that it fits well and is solid. We went on a 4000 mile adventure with a small motorcycle on the front hitch. etrailer has been a good source for for a few things now.
I own a 2003 Ford E-450 RV cutaway and wanted a front hitch to carry our bicycles since our rear hitch is used for a trailer. I originally tried to mount the equivalent Curt front hitch, because of its cheaper cost, onto the vehicle. However, the Curt hitch wouldn't work because it can't adequately accommodate the slight downward hump in the truck's frame. This hump can barely be seen between the two hitch mounting bolts. The hump is on both the left and right side frame rails on my vehicle. If your frame is not totally flat (has even a small hump) you cannot use the Curt hitch. The Curt's small indentation on its mounting flange will not adequately accommodate the frame's hump. This Draw-Tite hitch, 65001, mounted perfectly on my vehicle and the installation procedures I used were exactly as depicted in the etrailer video for the E350 van. In the video, the technician uses a rotary file to expand the rearward holes to allow the insertion of the bolts. I had to do the same thing and bought a rotary file for my drill at my local home improvement store for less than $3. I did not have to use the rotary file on the forward holes. In addition, I have the larger Roadmaster front sway bar and steering stabilizer and as you can tell in the photo, there is plenty of room for the hitch.
# 17
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
1998 Ford F-150 and F-250 Light DutyGreat product,easy installation and dealing with etrailer has been a real good experience.
# 18
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Product is great! Exceeds my expectations for ease of installation and performance. I removed the 3” spoiler completely vs cutting for hitch. The key is to “dry fit” in place and use a metal punch to mark all your drill holes. Wire bolt feeder worked great for installing bolts. I used the hitch to mount my eight pole rod & cooler holder for surf fishing.
Super fast shipping,but could use better packing.Hitch actually made a large hole in box,UPS driver had me check to see if anything was missing.Easy install,but try finding a 17/32" bit. After seeing how big the front opening is I just used a 1/2" bit. I think it took longer to remove, trim and reinstall the front spoiler than the rest of the job. Looks great installed
# 19
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I am not sure that installing this hitch could have been easier. I did it on the ground on my driveway, sloped, by removing my tow hooks and supporting the receiver on some blocks and bolting it in place directly into the frame. The hardware fit perfectly in alignment and thread size etc. We've mostly used it to carry bicycles when towing, though once placed a trailer with it also. Strong, fully functional and as noted easy to install.
Haven’t had a chance to use the front hitch on our Nissan Frontier year but the installation was quick and easy. I was all set to knock the installation out in 20 minutes until one of the split lock washers failed and had to be replaced out of my spare stock. Also an additional note: the hitch showed up heavily scratched despite the packaging having been in good condition. Maybe some more careful handling at the warehouse is in order.
# 20
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Installing onto my 2014 Silverado 1500 was a breeze. The only thing that caught me off guard was that I needed to cut a portion from the center of my splash guard for the rear bracket to be able to mount. I was only expecting to trim/remove the air dam as etrailer explained in the item description, which I still had to do. Other than that it was a perfect fit and I'm happy with the results. I plan to use this for a snow plow, winch, and many more interchangeable items for it.
I installed this front hitch by myself on a 2016 Chevy Suburban in about 3.5 hours with no floor jack. I use it to carry my mountain bikes when we are towing the trailer. The hitch sits 8.25” off the ground and extends out past the air dam about 3.5”. Once installed, the hitch is not very noticeable. A couple notes on the install: 1. The most difficult part is figuring out where to make the hole in the splash shield for the rear mounting point. I removed the splash shield and determined roughly where to cut a 1.5” hole based on the existing holes in the cross member. 2. To cut the air dam, I drilled small holes the the corners then used a utility knife to score and cut out the section. 3. I mounted the rear point first which gave me leverage to install the front easier. 4. The tape method for the 9/16 hardened washer and cone washer did not work for me. I had to finagle them into position as I was tightening the bolts (huge pain) 5. I had 4 extra 9/16 hardened washers. These are apparently supplied in case you need additional washers to fill the gap in the frame. I am very satisfied with this product and would definitely recommend it to others.
What our customers are saying:
"I think that the response time to a placed order is phenominal and the site is very user friendly, also I had found a few items on the site that were impossible to find at others so good job!!!"