Electric Jack Recommendation for Bumper Pull Horse Trailer
Published 08/07/2014
Question:
I have read all of your material and need to decide which jack to buy for my 2-horse bumper pull 4-Star trailer - I haul with Reese Equilizer bars to lift the weight off my truck as it is a bit under-powered. My tongue weight is only 1875#. There are so many to choose from it is difficult. I just need something to save my back during hookup. I am looking at either a Bulldog or the Atwood 80515.
asked by: Charmaine K
Expert Reply:
Since the Atwood Jack part # 80515 has been discontinued the decision would be pretty easy for you. The Bulldog Jack part # BD500200 is not only the obvious choice between the two you referenced, this jack is an excellent jack with plenty of power for your setup that has been reviewed highly by our customers who have bought and used it.
I attached an install and review video for this jack for you to check out as well.
Product Page this Question was Asked From
Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs - White
- Camper Jacks
- Pop Up Camper
- Teardrop Camper
- Travel Trailer
- A-Frame Jacks
- Steel
- 3001 - 4000 lbs
- Electric Jack
- 22 Inch Lift
- Bolt-On
- 1 Jack
- Bulldog
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: tongue jack
- Shop: Replacement Jack Foot for Dutton-Lainson 5,000-lb Trailer Jacks
- Shop: A-Frame Trailer Jack - Topwind - 5,000 lbs. by Dutton-Lainson
- Shop: Square A-Frame Jack w/ Footplate - Drop Leg - Sidewind - 28-3/4" Lift - 3,000 lbs
- Q&A: Troubleshooting A Roll Pin That Won't Slip Into Place In A Bulldog 10K Square Jack
- Video: Ultimate Overview of the Replacement Jack Foot for Dutton-Lainson 5,000-lb Trailer Jacks
- Video: A Closer Look at the Ultimate Trailer Jack
- Q&A: Availability of 5,000 lb Top Wind Trailer Jack with Grease Zerk Fitting
- Video: A-Frame Trailer Jack: The Breakdown
- Video: Hands-On with the Bulldog Square, A-Frame Jack
- Q&A: Trailer Jacks Manufactured in the USA
- Q&A: Are There Any American Made Trailer Tongue Jacks Available?
- Q&A: Replacement A-Frame Jack For Atwood Mobile Product Jack On Trailer With 2" Diameter Mounting Hole
- Shop: Round A-Frame Trailer Jack - Sidewind - 15-5/8" Travel - 5,000 lbs
- Shop: Ultimate Trailer Jack - A-Frame - Topwind - 27-1/2" Lift - 2,000 lbs
- Shop: Square A-Frame Jack w/ Footplate - Drop Leg - Sidewind - 28-3/4" Lift - 3,000 lbs
- Shop: Trailer Valet JXC Trailer Jack w/ Footplate and Drill Powered Option - A-Frame - Sidewind - 1.2K
- Search Results: awning
- Search Results: replacement awning
- Video: Bulldog Powered-Drive Kit Review
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2016 Dodge Journey
- Shop: Trailer Wiring
- Video: Let’s Check Out the Bulldog 2-Speed Jack
- Q&A: What Causes a Trailer Connector To Get Stuck Inside a Socket
- Q&A: How Does The etrailer Electric Trailer Jack e55ZV Hold Up In Cold Weather?
- Article: What are the Common Types of Propane Fittings Used on RVs?
- Article: The Best Electric Trailer Jacks of 2025
- Article: 5 Things to Know About Weight Distribution Hitches
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: 5 Tips to Confidently Choose Your Weight Distribution Hitch
on Camper Jacks
