Replacement Rubber Bumper For A Horse Trailer With A 81-1/2" Bumper Length

Question

Question:

I have a Corn Pro 2 horse trailer that needs a new bumper. The length of the bumper is 81 1/2 “ and I’m attaching some photos of the side sizes. Is the D3-96 the right part? Or do you have a shorter one, so we don’t have to cut it down?

asked by: Kat D

0

Rubber Bumper Width
(click to enlarge)

Rubber Bumper Height
(click to enlarge)

Expert Reply:

Hi Kat,

The rubber bumpers that we offer are all 96" in length but can come in different widths. Based on the dimensions you provided i your pictures the # D3-96 is going to be the best fit, but you will have to cut it down to size.

expert reply by: Kevin C

0

Answer 1

The bumper part #D3-96 that you referenced is our best option and could work for you but you will need to make some modifications. You would need to cut it down to the 84 inch length you need and would also need to drill new holes in it that line up…

view full answer...

Answer 2

All of our bumper strips are 96" long and have the holes pre-drilled out at 11" on center, but the nice thing is these can be cut and re-drilled to accommodate your application. You just need to choose which one has the width you're…

view full answer...

Answer 3

Hi Alan; as long as you don't have the factory OEM wheel liners you can use the WeatherTech Mud Flaps - Easy-Install, No-Drill, Digital Fit - Front and Rear Set #WT66MV on your 2025 Sierra 1500 Denali Ultimate.

view full answer...

Answer 4

The holes in the Redline #D2-96 Pre-Drilled Round Rubber Bumpers are 11-1/2 inches on center. You can see the full dimensions by looking at the photo I've edited for you.

view full answer...

Answer 5

You're right when referring to the #5 pin at the 10 o'clock opposite the ground wire when looking at the back of the trailer side connector. This should be the pin that corresponds to the brake controller output, but this will also depend on…

view full answer...

Answer 6

The only other extension option we carry besides the Torklift SuperTruss extender that does not cut your tongue weight in half is an extra long ball mount. Traditional extensions such as part #C45796 cut the tongue weight capacity of the hitch on the…

view full answer...

Answer 7

Hey Phillip. The Superwinch Terra Series ATV Winch item #SW1125230 definitely has the ability to do what you're wanting it to. It has a 50' rope and 2,500 lbs line pull. You are correct the 120v winches like item #DL25514 are going to run you…

view full answer...

Answer 8

Hi Jeff; I'm sorry to say that the Bauer Products Manger Door Lock for Horse Trailers #BA83FR does not have a keyed alike option. Each latch will be keyed unique. We do not have a product that matches and comes keyed alike either so individual…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hey Jack, If you're talking about a transition plate then you'll want the etrailer Enclosed Trailer Transition Plate #e32JR. This can be installed on either end of the ramp to help make the transition onto easier or at the hinge of the ramp…

view full answer...

Answer 11

Hello Drew, I'm glad that you wrote in. For your 2015 GMC Sierra 1500 you want part #RED26CR, this part number is the brake controller and the vehicle specific pigtail for you Sierra 1500. The #RED24FR you were looking is just the brake…

view full answer...

Answer 12

For flat towing your 2014 Chevy Silverado you would need to first start with a base plate kit. For that the Roadmaster kit part #RM-3176-1 has been confirmed as a fit and would work well. I attached an install video for you to check out as well. In…

view full answer...

Replacement Rubber Bumper For A Horse Trailer With A 81-1/2" Bumper Length

Product Page this Question was Asked From

Continue Researching