Replacement Parts for Thule 600 Cargo Box to Fit Thule AeroBars

Question

Question:

Hi, I have a huge and old Thüle 600 roof cargo box that I would like to fit to my Thüle Wingbar (Aerobar) 969 set on a Saab 9-5 Estate 2004. Please tell me which replacement mounting hardware kit with rubber pads for top and bottom clamps if possible would suit such combination best. Thank you in advance!

asked by: Alfredo R

1

Helpful Expert Reply:

You will want to pick up a Replacement QM3 kit, part # TH04997 . This includes all the pads, bolts, screws and plates to completely replace the mounting hardware.

I went to our warehouse and measured the mounting bracket and screws, and they together measure wide enough to hold a 3-1/2 inch wide by 1-1/2 inch tall ( 88.9mm by 38.1mm) sized Thule Wingbar.

expert reply by: Jacob W

1

click to enlarge

Answer 1

I do not have a specific set of instructions for the Thule QM3 Quick On-Off Mounting Hardware Kit, item #TH04997, but I did come up with a drawing, see attached, that shows exactly how the parts of the kit install.

view full answer...

Answer 2

To replace the mounting hardware for your older Thule 600 Classic Cargo Box you can use the Quick Mount Hardware Kit #TH04997. This kit includes the reinforcing plates, Quick On components, carriage bolts, and hand knobs necessary to secure it to…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The parts you'd want to tow the Coachmen Clipper Ultra Lite with your 2022 Subaru Ascent would be the etrailer hitch part #e55ZR, then for trailer wiring you'd need the 7-way kit part #118290. Then for a brake controller the Curt Echo Mobile…

view full answer...

Answer 6

I can certainly help you out. The hardware used on the Thule Adventurer is #TH04997 that you have referenced. There is a specific order in which all of the parts will go on the crossbars. I have included a picture that shows how all of the parts go…

view full answer...

Answer 7

If you need replacement mounting hardware for your Thule Cascade Rooftop Cargo Box then we can help with this using the parts listed below. Unfortunately, we don't have any way to convert this mounting system over to a newer and easier to use…

view full answer...

Answer 8

We have exactly what you need for your Thule Summit! Take a look at the: -Replacement QM3 - Quick Mount Hardware - for Adventurer Cargo Box #TH04997. Even though it does not say it's for a Summit cargo box, this is the same hardware that was…

view full answer...

Answer 9

The u-bolt that you are looking for is no-longer available. We have two different options depending on what mounting hardware your Cascade has. The Replacement EasySnap Mounting Hardware #05704 if your box has the quick snap hardware or the…

view full answer...

Answer 10

The original mounting hardware for the Thule Cascade XT is no longer available. A good alternative is the Thule Replacement Quick Mount Hardware #TH04997. This fits crossbars up to 1-9/16 tall x 3-3/4-inches wide. If you end up needing to drill new…

view full answer...

Answer 11

The Thule Replacement QM3 Brackets #TH04997 has mounting holes 4" (center on center) apart, so they're going to fit much wider crossbars than your current brackets which only allow for bars around 2" wide and are designed for square…

view full answer...

Replacement Parts for Thule 600 Cargo Box to Fit Thule AeroBars

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching