Replacement Parts For Kar Kaddy 2 Tow Dolly

Question

Question:

I cant seem to find all the parts for my 80s model kar kaddy 2 Im trying to restore it and need to replace several parts but can not find any parts for it

asked by: Jacob J

1

Helpful Expert Reply:

I can't promise we have all the parts you need for your 80's model Kar Kaddy 2. We do have the Replacement Hub Assembly for Demco Kar Kaddy Tow Dolly - Qty 1 # DM04369 and many other parts that may work but aren't specific to your car dolly. Let me know what you are looking for and I'll see if I can help.

expert reply by: Jason S

1

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

I sure can Bob and thanks for the information! Since you have a Lippert 3,500 lbs axle you'll be able to use the Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles item #AKHD-545-35-EZ-K, you were looking at. These have a 5 on 4-1/2 lug nut…

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

I reached out to my contact at Demco and he said that the Kar Kaddy SS #DM9713045 can be assembled by 1 person and that it typically takes about 3-4 hours. If you are a retired auto mechanic then it will likely be on the lower end as you have…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 9

Demco has an interesting way to determine if the Kar Kaddy X #DM9713093 would provide enough ground clearance for a vehicle like your 2006 Mini Cooper to load. You will need to measure from where the front wheel touches the ground on front side of…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 12

Hello Jeff, The Taskmaster Steel Modular Trailer Wheel - 14" x 6" Rim - 5 on 4-1/2 - Black PVD Finish #460545MBPVD is not compatible with the Demco Kar Kaddy SS because it has a zero offset like most trailers require. We do not have the…

view full answer...

Replacement Parts For Kar Kaddy 2 Tow Dolly

Product Page this Question was Asked From

Continue Researching