Brophy Slide In Camper Tie-Downs - No Drill Bed Mount - Qty 4
(216 reviews)
Price: $206.32
In Stock
Brophy Slide In Camper Tie-Downs - No Drill Bed Mount - Qty 4
Item # HSSF
Retail:$217.64
Our Price: $206.32
You Save: $11.32
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (216)
- Q & A (0)
- Photos
- Used (2)
Brophy Camper Tie-Downs - HSSF
- Front and Rear Tie-Downs
- Brophy
- Bed-Mounted
- Powder Coated Steel
Steel brackets clamp onto the side rails of your non-dually, full-size pickup with no drilling required. Creates a dependable anchor point for securing your lightweight camper to the bed. Simple to install and to remove.
Features:
- Creates attachment points for securing your camper to your truck bed
- Wide clamps provide superior holding strength
- Turnbuckles (sold separately) required to attach camper to tie-downs
- Protects your truck's paint with neoprene pads attached to the brackets
- Resists corrosion and rust with black powder coated steel
- Clamps securely onto your bed rails - no drilling required
- Includes 4 camper tie-downs with clamp plates, 12 neoprene pads, and installation hardware
- Made in the USA
Specs:
- Application: for exact fits, enter in your vehicle's year/make/model above
- Minimum 2" needed between sidewall and lip of bed rail
- Not compatible with drop-in bed liners, aftermarket bed rails, double-walled beds, or side-step beds
- Dimensions: see diagrams below
- 1-Year limited warranty
No-Drill Installation
These clamp-on tie-downs install quickly and easily, with no drilling or modification to your truck required. Because they're mounted in the bed instead of on the frame or body of your truck, you don't need any kind of fancy mechanical background to get this job done. You just need to slide the hold downs over the rails of your truck and clamp them down with the included T-bars and hex bolts.
The fact that they simply clamp on means that you can remove these tie-downs when you're not hauling your camper, leaving no trace. Use the provided neoprene pads on the T-bolts and tie-downs where they make contact with your truck to make sure no scratches or dents will be left behind either.
It's important that the tie-downs on your truck line up with the anchors on your camper at the correct angle to ensure a secure hold. Ideally the tie-downs should be on the outside of your camper's anchor points, but they can be on the inside as well, just as long as they're not lined up with each other.
Securing your Camper
To secure your camper to your truck, you'll also need a tie-down hardware package consisting of turnbuckles, S-hooks, and chains (TDHP - sold separately). This hardware attaches the anchors on your camper to the tie-downs on your truck to keep your camper safely mounted. Once you tighten the turnbuckles to the correct level of tension (not too tight!), you'll be good to hit the road.
HSSF CR Brophy Truck Camper Tie Downs for Slide In Truck Camper - Camper Hold Down - No Drill Tie Down - 4 Pack
Installation Details
Customer Satisfaction Score:
91% were satisfied with this product
9% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- etrailer mistake
Customer Reviews
Brophy Slide In Camper Tie-Downs - No Drill Bed Mount - Qty 4 - HSSF
Average Customer Rating: 4.6 out of 5 stars (216 Customer Reviews)
Steel brackets clamp onto the side rails of your non-dually, full-size pickup with no drilling required. Creates a dependable anchor point for securing your lightweight camper to the bed. Simple to install and to remove.by: TheAvionNomad01/18/2024
I used these to mount a vintage 1970 Avion C-11 to a 1993 D250. They worked great and were much stronger than I expected - and it was a huge cost savings (and a much more attractive look) than some of the frame mounted options of more than $1000. There were some oddities that I noticed. It was impossible to mount them exactly the way the instructions suggested because of where on the wings near the cab,. The brackets also could not stay on with the camper unloaded because they would hit the jack mounts, meaning they had to me bolted in after the camper was in the truck but before lowering the jacks, making the access to the bolts a frustrating 'feel for it' experience.I'f suggest the manufacturer secure the bolt so that you don't need to hold both sides when tightening/loosening, and also refine it to need less turns to do so. It took me 2 hours to mount the first time, and not much less when removing them with the limited access. The pads also came off in the first use.
I gave it a 5 star because I realize there are limited options for older campers and anything universal is going to have issues with some thing - so that's just my input and experience. Overall pretty reasonable for the price and functionality.
by: Pat03/20/2023
The product was shipped extremely quickly, it arrived 3 days after I ordered them. As far as the product goes I was extremely pleased that they were as easy to install as the product video showed them to be. I had been looking for
a tie down system that would work for my 2018 Ford since I purchased my camper in 2020 and after much research I found these at etrailer. One word of advice is that if your camper has a shower or other design that allows the camper to extend across the bed behind the wheel wells, either move the rear tie downs forward or shorten the leveling stud before you attempt to load your camper. On mine it turned out that once the tie downs were placed and attached I had to cut off about 3 inches of the threads.
Other than that it was an easy install although the bolts that attach the tie downs to the under lip clamp are a challenge to install but take your time and they will go on. I will post an update once I have been on the road for a few trip and see how they are working.
Thank you etrailer for your super fast shipping and online product videos.
by: Jeff Smith10/22/2023
These tie downs work great. It holds my 3k lb Cabover camper in place without issues. And I live in my camper, so not losing my home is very important to me!!
by: Ed B.05/21/2019
Purchased the Brophy camper tie down set of four for the Palomino truck camper I just purchased. These are my second set as the first set were sold with my Hallmark camper. Easy to install and hold the camper in the truck with no worries.
by: Shelly12/13/2023
The products arrived on the time scale as stated. The packaging did not hold up and the box with the metal tie downs was broken open. There was too much weight for the box and it just split open. Not sure if anything is missing. Packaging of items that are heavy should be more secure and sturdy.
Jenny N.
12/14/2023
Oh no! I will have our Customer Service team reach out to you. If anything is missing we can take care of it.
by: Allen.08/22/2022
These wont work for my truck and camper. The box on a 2018 gmc 2500 short bed does not lend well to placement of these in order to get the correct geometry i needed for the tie-down points on my Palomino maverick 6601. I had high hopews of not having to buy the frame mounts, but i will have to.
Mike L.
8/31/2022
The HSSF tie downs have specific fit parameters as mentioned in the product specifications above: External bed rail width cannot exceed 5-12 Requires at least 2 of space beneath lip of bed rail Not compatible with -in bed liners, bed rails, double-walled beds, or side-step beds
Allen.
8/23/2023
In response to the etrailer comment response, they fit on the bed fine, with plenty of clearance and would work for a smaller camper. they just did not fit in the right spots for my truckcamper combo.
by: Ron W07/02/2016
As far as I'm concerned these are junk. Wasted my money. Do not mount in proper location on a 2011 Chevy Silverado 6.5' Bed. Because of the design of the bed rail the mounts cannot be installed in the proper locations for securing camper. The photos show the maximum forward and back that these can be mounted. Not at all made for the 6.5 foot bed 2007 or later Siverado. The Black Powder Coated Steel isn't that great either. Paint missing, dinged up from storage and shipping probably.
by: Brent 08/08/2019
I bought these for our brand new 2019 GMC Sierra 1/2 ton because no custom options were available. I was happy that they were easy to install, and look great. I’ve used them in the past and have been happy with how they hold campers. Sure I’d rather have custom mounts from the frame, but for the price and because these are my only option that’s what I got. These will work just fine, and I like that I can swap these out on trucks.
The one thing I wish was different was that the threaded T handle portion would have a longer option. I had to fancy up a 2”x6” to run inside the side of my p/u bed so they would touch something.
As always another great shopping experience with etrailer. They haven’t let me down yet. Especially Lori, what a great customer service rep.
by: Matt04/14/2015
These camper hold-downs appear to be manufactured from good steel stock and should do the job nicely. I did have one piece that was slightly damaged but was not caught when packaged (the damage was not due to shipping). I was able to take a hammer to the bent steel and straighten it sufficiently to use the part. It was a little disappointing however, and should have been caught prior to shipping.
Overall I am pleased with the quality and price
by: . George01/03/2024
The tie downs are great no problems.Very easy to install.I keep them on my truck all year long Thank you
by: Terry08/08/2023
Order arrived quickly, priced ok. Box was broken open by shipper NS the 4 T-bolsts bolts ere missing. Etrailer shipped ou the missing parts a few days later, but in the meantime I fashioned t-bolts I could use for my trip. Many customer comments on this camper Brophy tie-down match my experience. Etrailer follow up was great, but surely must be aware that their packing is sub-standard. Perhaps zip-tying the T-bolts to larger pieces would eliminate the loss even in case of breakage. Functionally the tie-dows were easy to install and seem quite adequate for off-road use of my in-bed camper. Will continue to use etrailer because of their excellent customer service.
by: captkirk02/15/2021
These tie-downs worked awesome for our pop up camper on our 1998 F150. Super snug, haven't loosened up or moved on the truck, camper hasn't budged either. I was leary at first not having the camper tied to the frame but now I have total faith in these tie downs.
by: Mike S05/23/2020
These Brophy tie downs have worked great over the past year. I leave the camper on the truck and it is my daily driver as well as RV. The camper weighs in at 1500 dry and about 2000 loaded. I do not do any radical 4x4 but I have taken some backwoods off road logging trails.
by: Bing09/23/2019
I received this tie downs on July, and first used it yesterday.
My Camper ‘s dry weight is about 1600 lb, and the products are good for my truck camper.
The problem was the position where tie downs were fitted on my truck. I tried several times to fitted tie downs to my truck.
by: Chuck11/13/2012
Found easy to install, I placed lock washers on the 8 3/8" bolts. Sold at Menards for 89 cents (pkg of 8) not in kit. Placement was a little restrictive with dealer installed bed liner. Takes 30 minutes to install all 4. Great buy.
by: Regan06/25/2019
Using on 2013 Ford F150 for a smaller cabover. Great quality product, shipped fast, works great. Had to turn bolts around to clear inside of bed. Held camper solidly over rough trails!
by: Patrick04/02/2020
These things are solid although i put duck tape on the T pads....installed 2014 Chevy Silverado 6.5 ft bed for 1200lb Starcraft.
Patrick
4/6/2021
Still have not moved! Great design and cost savings.
by: Bryce05/10/2022
Fits well on a First Gen Tundra. I was extremely unsure about fitment for my truck but they work great! Install only takes 5-10 minutes. I would definitely recommend. Steel is quite thick and seems very strong.
by: Neil08/04/2021
Arrived on a rainy day with the box falling apart. Too much heavy steel to be loosely packed. Fortunately, the hardware bag was still there. Some bare metal showing. I had some emails with MacKenzie B. and they were responsive and without asking they offered me a 5% refund for the damage. After my first trip, they performed well on some very bumpy roads. Held strong and didn't move. I did have to re-adjust the lower standoffs after the first week. Taking them on/off is frustrating because the 2 nuts are in the small gap behind the clamp against the inner bed wall. Too tight for all but an open end wrench. 1/6 turn times too many fumbling tries, arg! Also, I was nervous not having a locking feature (lock washer, locknut, etc). I bought 8 locknuts (pinch type) and welded them to the inner plate. Then bought 8 round head hex bolts (grade 8). So now I can install easily with an Allen socket. See pictures. Recommend eTrailer consider this modification.
Neil
8/5/2022
After my mount bolt mod, Ive used these multiple times and they are working great! Very stout and no visible marks on my F250 bed.
by: Andrew07/22/2021
If I could give a 3.5 out of 5, I would. These tie-downs serve their purpose, but definitely not recommended for a bigger camper. I would say my camper is average sized. These tie-downs hold my camper in place the majority of the time, some small movements when I'm on rough roads, but nothing too dramatic.
Negatives.
Two of the four lost the padded backing where the tie down meets the inside of the truck bed. Had to go buy some foam and create my own. They flex quite a bit with a camper the size of mine, wouldn't go down any rough roads.
by: John05/25/2020
Easy to install and have done what’s expected. Keep the camper in place!!
by: JAMES K09/24/2012
ORDER ON TUESDAY RECIEVED ON FRIDAY NOON SAME WEEK ONLY PROBLEM WAS 4 7/ 16 NUT WERE 4 1/2 NUT HAD TO BUY 4 NUTS OTHER THEN THAT I WOULD BUY OFF ETRAILER AGAIN VERY GOOD SERVICE
by: Jason S.06/05/2019
These tie downs were a great budget solution in leu of a permanent installation of my camper shell and/or frame mounted tie downs. Aside from needing to plan their placement (they can hang in front of the gas cap if you don't plan it right the first time around... no, I didn't accidentally block my gas cap... maybe I did) and take into consideration they also need a little bit of internal clearance as well, they work just fine. I haven't noticed any cargo shifting nor warping of the truck bed around where they are installed. My camper shell is under 1K lbs and it holds just fine.
Jason S.
6/8/2020
A year later & they still hold strong.
by: D Gagnon05/14/2017
Could be happier took about 15 minutes to install can't wait to go camping
by: Dayton12/15/2023
Awesome customer service my new fav pl ace
25
216
Show More Reviews
See what our Experts say about this Brophy Camper Tie-Downs
- Will Brophy Camper Tie Downs Fit a 2009 Ford F-150 STX and Not Interfere with the CamperIt is likely the hardware that sticks out into the bed that is causing some fit issues with the Brophy tie downs # HSSF. But if you have 8 inches of clearance on each side with your 2009 Ford F-150 STX then I don't see there being a problem. On the off chance that there is an issue part of the T-bolt sticking into the bed could be trimmed away. With these tie downs we also recommend hardware package # TDHP to secure the camper to the tie downs. I have linked a video featuring these products...
view full answer... - Can I Use the Brophy Clamp On Camper Tie Downs on 2019 Ram 2500 With Double Walled BedAs long as the double wall still allows for the clamp on the underside of your bed rail, the Brophy Tie-Downs # HSSF will work on your 2019 Ram 2500. The brace on the bottom is adjustable so it will account for the additional wall on the inside of the bed. If you don't have the lip under the rail then you may want to instead consider the Brophy Stake Pocket Mounted Camper Tie Downs - Bed Mount - Black Powder Coated Steel - Qty 4 # TDSF since they won't utilize that lip or the inside of...
view full answer...
- Camper Tie-Downs for 2007 GMC Sierra 2500 New Style with 6-1/2-ft BedThe correct choice of camper tie-downs for your 2007 GMC Sierra 2500 New Style with 6-1/2-ft bed will depend on whether it is equipped with running boards and on what type of hitch is installed: factory, aftermarket or Torklift. The link provided will take you to our main page for tie downs for your truck. The drop-down 'Select Vehicle Style' menu at the top of the page will let you select your particular truck's configuration to see compatible tie down kits. For example, if your truck...
view full answer... - Fitment of Tie-Downs for 2005 Dodge Ram Pickup 3500 DuallyFor your 2005 Dodge Ram Pickup, 3500 series Dually with 8 foot bed I suggest, the TorkLift Custom Frame-Mounted Camper Tie-Downs - Rear, # TLD3109 and Front, # TLD2101. The tie-down inserts can be easily removed from frame-mounted receiver brackets with included pins. The brackets fit tight to truck frame - no loss of ground clearance. All necessary hardware included. These currently have a 4.8 rating from over 700 reviews. Please note the linked installation videos below. The Brophy...
view full answer...
- Comparing Brophy Truck Bed Camper Tie DownsOn the ends of the Brophy tie downs # HSAB where you would tie off the camper the tip is turn up to be parallel with the ground. The angled design allows more clearance between hold-downs and truck fenders.On # HSSF the tips are not turn up and are at about a 45 degree angle. For either kit I also recommend the associated hardware package # TDHP.
view full answer...
- In-bed Camper Tie Down Recommendations for a 2009 Dodge Ram 1500The Extang CargoCleats Truck Bed Tie-Down Anchors - Clamp On - 500 lbs - Qty 2 # EX1932, have a weight capacity of 500 lbs each. You will have to also make sure that the straps that you use also have enough strengths for the application. The tie-downs fit underneath the bed rails like in the video I have linked for you. Provided there is nothing in the way they could fit your 2009 Dodge Ram 1500, they are a universal fit, but will not work if you have the OEM bed rail cap installed. Since...
view full answer... - Camper Tie Down Recommendation for a 1988 Chevy K2500The camper tie downs, # TDSF, will not work with 1988 and newer Chevy/GMC trucks. If your truck is not a step side, does not have a double-wall bed, and is not a dually, you can use # HSSF with hardware package # TDHP. I have included some pictures that show how the tie downs install.
view full answer...
- Recommended Stake Pocket Anchors for a 1996 Ford F-250 For your 1996 Ford F-250, I recommend going with the Brophy Stake Pocket Mounted Camper Tie Downs # TDSF. These are universal anchors that will work with your 96 F-250, can be used in any pocket, and measure 5-1/2" tall x 1-7/8" wide x 3/8" thick. These anchors do require drilling so this is going to be a permanent install, however if you'd prefer a non-permanent install the Brophy Clamp On Camper Tie-Downs # HSSF will work just as good.
view full answer... - Camper Hold Down Recommendation for a 2007 Dodge Ram 2500The Brophy Camper Hold Down Brackets, part # HSSF are a universal-fit item that will work on most full-sized trucks, including your 2007 Ram 2500. Some Dual rear wheel truck beds may interfere with the installation of the hold downs. The brackets wrap around the bed rail, instead of using the stake pockets. The brackets include the hardware for fastening the bracket to the truck, but we also offer hardware to attach the camper to the brackets, the kit is part # TDHP. The kit includes...
view full answer... - Stake Pocket Camper Shell Tie Down Recommendation for 2015 Chevy Silverado 2500For stake pocket camper tie-downs you would want the Brophy part # HSSF which would fit in the stake pockets of your 2015 Chevy Silverado 2500 and would work well for you. You would also need the part # TDHP for hardware. I attached an install video for you to check out as well.
view full answer... - Will the Brophy Camper Hold Downs # HSSF Fit on a 1996 Ford F-150Yes, the Brophy Camper Hold Downs, item # HSSF, will fit on your 1996 Ford F-150. These Hold downs do not install in the stake pockets, but wrap around the bed side. The instructions, see attached link, show the installation in detail. You may also be interested in the Camper Tie Down Hardware Package, item # TDHP.
view full answer...
- 2004 Ford F150 FX4 6.5 ft bed Camper Tie Down RecommendationWe don't have a lot of specific fit information for the Brophy Tie-Downs part # HSSF that you referenced, but we do know that they can't be installed on a 2004-2008 Ford F-150. The best option I can make for you would be the # TDSF that installs in the stake pockets. You will also want the hardware kit part # TDHP.
view full answer... - Will Brophy Camper Hold Downs # HSSF Fit a 2009 Dodge Ram 1500 With a Bed LinerThe Brophy Camper Hold Downs, part # HSSF, will fit trucks with spray-in bed liners, but if it has a slide-in bed liner the bed liner will have to be trimmed away in the shape of the hold downs. The installation does not involve any drilling or modification to the truck bed. It is installed by tightening two bolts on each clamp. I am including a link to the installation instructions for the hold downs. You may also be interested in the Camper Tie Down Hardware Package, part # TDHP.
view full answer...
- Will the Brophy Clamp On Camper Tie-Downs Work On a 2018 Ford F-150 with Aluminum BedI have spoken with Brophy in the past about using the Brophy Clamp On Camper Tie-Downs on a Ford F-150 with aluminum bed and they said so long as you use part # HSSF there won't be any issues. In order to secure the truck bed camper to these tie-downs you will also need the Brophy Basic Turnbuckles w/ Hardware for Camper Tie-Downs part # TDHP.
view full answer... - Will Brophy Camper Tie Downs Work on 2020 Chevy Silverado 2500 Long BedYes, the Brophy camper tie downs part # HSSF that you referenced can fit truck bed that have plastic bed rail covers like your 2020 Chevy Silverado 2500. I attached a picture that shows them installed on a bed rail that has the covers like you mentioned. For hardware to attach the tie downs to the camper we have the # TDHP as well.
view full answer...
- Camper Tie Down Recommendation for 2015 Chevy Silverado 3500 with Wheel to Wheel Nerf BarsSince you have wheel to wheel step nerf bars the only solution for camper tie downs would be a Brophy kit like the part # HSSF which attaches to the stake pockets. The Torklift kits would interfere. Then for a hardware kit to attach the camper to the truck bed you would also need the part # TDHP.
view full answer... - Can the Brophy Clamp On Camper Tie-Downs Be Used On a Ford F-150 with Aluminum BedWe have spoken with Brophy in the past and for a Ford F-150 with aluminum body such as your 2017 model they recommend using the Brophy Clamp On Camper Tie-Downs part # HSSF. There won't be any issues with these tie downs and an aluminum bed so long as you are not exceeding other figures such as payload capacity etc. In order to secure the truck bed camper to these tie-downs you will also need the Brophy Basic Turnbuckles w/ Hardware for Camper Tie-Downs part # TDHP. Although certainly...
view full answer...
- Will Brophy Camper Tie-Downs # HSSF Fit A 2018 GMC Sierra 2500HDHey David, The Brophy Slide In Camper Tie-Downs # HSSF could potentially work but you'll first want to ensure you have enough clearance for them to fit up against the inner lip of the bedrails and clear the side body of the bedrails. I've attached a diagram below of their dimensions so you can measure your bedrails and confirm fitment. To complete the setup Brophy also offers turnbuckles with part # TDHP.
view full answer... - Can I Use # HSSF Camper Hold Down Brakets in My 2000 Dodge Ram for my 11-1/2 ft Camper ShellThese Camper Hold Down, part # HSSF, are universal fit items made to fit most trucks. These hold downs wrap around the truck bed rails and are mounted inside the bed. Like other products, they do not fit in the stake pockets. Some dual rear wheel beds interfere with installation of the hold downs. You will want to check, however, that your vehicle manual does not state that you would be unable to use sidewall type camper hold downs. Otherwise, these should work well to secure your 11-1/2...
view full answer... - Camper Tie-Downs for a 2012 Dodge Ram Crew Cab with 5-foot, 7-inch BedTorkLift does not list any fits for your 2012 Dodge Ram Crew Cab with a five-foot, seven-inch bed. But I do have another option for you. I recommend going with Brophy Camper Hold Down Brackets, # HSSF. These are a universal-fit item that will work on most full-sized trucks, including your 2012 Ram Pickup. The brackets wrap around the bed rail, instead of using the stake pockets. The brackets include the hardware for fastening the bracket to the truck, but we also offer hardware to attach...
view full answer... - Will Brophy Camper Tie Down HSSF Fit 2011 Ford F-150While we don't have feedback for the # HSSF on your 2011 Ford F-150 positive or negative we have recommended these for several customers with F-150s similar to yours and have not heard back saying they didn't fit. Typically people are more likely to leave feedback when something doesn't work so in this case I would say that no news is, "good news." For the hardware kit to attach the camper to the tie downs you would also want the part # TDHP.
view full answer...
- Will Brophy Camper Hold Downs # HSSF Fit a 1998 Dodge Ram 2500The camper hold downs, # HSSF, will fit your 1998 Dodge Ram and hold a camper that is appropriately sized for you truck. The recommended hardware package, # TDHP, as a listed capacity of 3,000 pounds so the 2,620 pound gross weight of the camper should not be a problem. I have included a link to a video review and the instructions for you. The best option is going to be frame mounted tie downs. I have included a link to the options for the 1998 Ram. You will have to use the drop down menu...
view full answer... - What Are the Correct Camper Tie Downs for a Regular Cab Long Bed 2018 Ram 3500 SRWFor a 2018 Ram with a long bed, regular cab, diesel 4x4 in SRW configuration without running boards but with a receiver hitch, the correct TorkLift Talon Custom Frame-Mounted Camper Tie-Downs for the rear is, # TLD3109A. For the front, the TorkLift Custom Frame-Mounted Camper Tie-Downs, # TLD2129 is the recommended item but due to the compressor location this Tie Down can't be installed with factory airbags on 8 foot bed. I suggest the Brophy Clamp On Camper Tie-Downs, # HSSF in black...
view full answer... - Quantity Of the Brophy Camper Hold Downs Come with the # TDSF # HSSF and # HSABAll of the Brophy Truck Bed Camper Hold Downs like the # TDSF, HSSF, and the HSAB are sold in a quantity of 4.
view full answer...
Do you have a question about this Camper Tie-Down?
Used Items Available
Condition: Installed
Notes: Item has been installed/test fit.
Condition: Surface Scratches
Notes: Parts are scratched up, seems to be some signs of instalation, otherwise fine.
Info for this part was:
Expert Research:
Mike L
Expert Research:
Sarah L
Expert Research:
Robert G
Expert Research:
Patrick B
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Reno H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Brandon M
Expert Research:
Adam R
Expert Research:
Jeffrey L
Expert Research:
Sarah H
Video Edited:
Zack K
Video by:
Patrick B
Installed by:
Matthew K
Installed by:
Cole B
Updated by:
Rachael H
Updated by:
Amanda M
Updated by:
Manda E
Updated by:
Amanda K
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Ed B.
5/22/2020
No problems. Would buy again. Very easy to take on and off the truck.